Skip site navigation (1)Skip section navigation (2)
Date:      Wed,  4 May 2005 19:00:45 -0400
From:      benash@eecs.umich.edu
To:        Wilko Bulte <wb@freebie.xs4all.nl>
Cc:        freebsd-alpha@freebsd.org
Subject:   Re: FreeBSD 5.3 on Digital Personal Workstation 500au
Message-ID:  <1115247645.4279541da60e0@mail.eecs.umich.edu>
In-Reply-To: <20050504210854.GA82595@freebie.xs4all.nl>
References:  <1115240233.42793729bff3f@mail.eecs.umich.edu> <20050504210854.GA82595@freebie.xs4all.nl>

next in thread | previous in thread | raw e-mail | index | archive | help
OK, it looks like I fixed the problem.  I needed to have the SCSI card in a
64-bit slot WHILE the other two cards were removed (so that nothing was plugged
into a 32-bit slot).  The 5.3 installation seemed to complete without trouble,
and I am able to login as root.

Any ideas as to why this fixed things?

Ben Nash
benash@eecs.umich.edu



Quoting Wilko Bulte <wb@freebie.xs4all.nl>:

> Sounds similar (IIRC) to the problem reported for the PWS and
> 5.4-RC
>
> No resolution that I have seen though :-(
>
> W/
>
>
> On Wed, May 04, 2005 at 04:57:13PM -0400, benash@eecs.umich.edu wrote..
> >
> >
> > Hi,
> >
> > I am trying to install FreeBSD 5.3 onto a Digital Personal Workstation
> 500au.
> > However, when booting from the CD (or floppies), the CPU halts and attempts
> to
> > boot again.  The output of this loop is shown below, along with some
> > configuration info below that.  I have tried moving the SCSI card from the
> > 32-bit slot to a 64-bit slot, and I also tried removing the other two PCI
> > devices (a NIC and a graphics card).  Neither action made any difference.
> >
> > All the firmware has just been updated to the latest version.  Also, I am
> able
> > to install version 4.11 from CD without any problem.
> >
> > I would really apreciate any hints or ideas that people have on this.
> >
> > *** keyboard not plugged in ...
> >
> > ff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.CPU 0 speed is 2.00 ns (500MHz)
> >
> > Digital Personal WorkStation 500au5.e4.
> > Console V7.2-1 Mar  6 2000 14:47:02
> >
> > CPU 0 booting
> >
> > >>>^C
> > >>>b dka0
> > (boot dka0.0.0.4.0 -flags a)
> > block 0 of dka0.0.0.4.0 is a valid boot block
> > reading 410 blocks from dka0.0.0.4.0
> > bootstrap code read in
> > base = 1d8000, image_start = 0, image_bytes = 33400
> > initializing HWRPB at 2000
> > initializing page table at 1ca000
> > initializing machine state
> > setting affinity to the primary CPU
> > jumping to bootstrap code
> > Console: SRM firmware console
> > VMS PAL rev: 0x1000000010114
> > OSF PAL rev: 0x1000000020116
> > Switch to OSF PAL code succeeded.
> >
> > FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> > (root@ds10.wbnet, Fri Nov  5 04:07:45 UTC 2004)
> > Memory: 655360 k
> > Loading /boot/defaults/loader.conf
> > /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> > |
> > Hit [Enter] to boot immediately, or any other key for command prompt.
> > Booting [/boot/kernel/kernel]...
> > Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> > Copyright (c) 1992-2004 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> >         The Regents of the University of California. All rights reserved.
> > FreeBSD 5.3-RELEASE #0: Fri Nov  5 11:30:09 UTC 2004
> >     root@ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
> > Digital Personal Workstation (Miata)
> > Digital Personal WorkStation 500au, 500MHz
> > 8192 byte page size, 1 processor.
> > CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
> > OSF PAL rev: 0x1000000020116
> > real memory  = 669147136 (638 MB)
> > avail memory = 641531904 (611 MB)
> > cia0: <2117x Core Logic chipset>
> > cia0: Pyxis, pass 1
> > cia0: extended capabilities: 1<BWEN>
> > cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
> > pcib0: <2117x PCI host bus adapter> on cia0
> > pci0: <PCI bus> on pcib0
> > dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem
> 0x80140000-0x8014007f irq
> > 0 at device 3.0 on pci0
> > miibus0: <MII bus> on dc0
> > nsphy0: <DP83840 10/100 media interface> on miibus0
> > nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > dc0: Ethernet address: 00:00:f8:75:af:31
> > dc0: if_start running deferred for Giant
> > dc0: interrupting at CIA irq 0
> > dc0: [GIANT-LOCKED]
> > atapci0: <CMD 646 WDMA2 controller> port
> > 0x9080-0x908f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 1 at device 4.0 on
> pci0
> > atapci0: interrupting at CIA irq 1
> > ata0: channel #0 on atapci0
> > ata0: interrupting at ISA irq 14
> > ata1: channel #1 on atapci0
> > ata1: interrupting at ISA irq 15
> > isab0: <PCI-ISA bridge> at device 7.0 on pci0
> > isa0: <ISA bus> on isab0
> > pcib1: <PCI-PCI bridge> at device 20.0 on pci0
> > pci1: <PCI bus> on pcib1
> > pci1: <display> at device 8.0 (no driver attached)
> > isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem
> > 0x80070000-0x80070fff irq 16 at device 9.0 on pci1
> > isp0: interrupting at CIA irq 16
> > isp0: [GIANT-LOCKED]
> > xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x8100-0x817f mem
> > 0x80071000-0x8007107f irq 20 at device 10.0 on pci1
> > miibus1: <MII bus> on xl0
> > xlphy0: <3Com internal media interface> on miibus1
> > xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > xl0: Ethernet address: 00:10:4b:95:ab:ac
> > xl0: interrupting at CIA irq 20
> >
> > halted CPU 0
> >
> > halt code = 5
> > HALT instruction executed
> > PC = 1f00
> >
> > CPU 0 booting
> >
> > (boot dka0.0.0.4.0 -flags a)
> > block 0 of dka0.0.0.4.0 is a valid boot block
> > reading 410 blocks from dka0.0.0.4.0
> > bootstrap code read in
> > base = 1d8000, image_start = 0, image_bytes = 33400
> > initializing HWRPB at 2000
> > initializing page table at 1ca000
> > initializing machine state
> > setting affinity to the primary CPU
> > jumping to bootstrap code
> > Console: SRM firmware console
> > VMS PAL rev: 0x1000000010114
> > OSF PAL rev: 0x1000000020116
> > Switch to OSF PAL code succeeded.
> >
> > FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> > (root@ds10.wbnet, Fri Nov  5 04:07:45 UTC 2004)
> > Memory: 655360 k
> > Loading /boot/defaults/loader.conf
> > /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> > |
> > Hit [Enter] to boot immediately, or any other key for command prompt.
> > Booting [/boot/kernel/kernel]...
> > Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> > Copyright (c) 1992-2004 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> >         The Regents of the University of California. All rights reserved.
> > FreeBSD 5.3-RELEASE #0: Fri Nov  5 11:30:09 UTC 2004
> >     root@ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
> >
> > /* THIS PROCESS REPEATS FOREVER . . . */
> >
> > >>>show dev
> > dka0.0.0.4.0               DKA0        TOSHIBA CD-ROM XM-6102B  1106
> > dkc0.0.0.1009.0            DKC0       QUANTUM ATLAS10K2-TY184L  DA40
> > dva0.0.0.0.1               DVA0
> > ewa0.0.0.3.0               EWA0              00-00-F8-75-AF-31
> > pkc0.7.0.1009.0            PKC0                  SCSI Bus ID 7  5.57
> > pqa0.0.0.4.0               PQA0                       PCI EIDE
> > pqb0.0.1.4.0               PQB0                       PCI EIDE
> > >>>show conf
> >
> > Firmware
> > SRM Console:    V7.2-1          Mar  6 2000 14:47:02
> > ARC Console:    5.70
> > PALcode:        OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
> > SROM Version:   v5.90
> >
> > Processor
> > DECchip (tm) 21164A-2   Pass   500 MHz  96 KBytes SCache
> > 2 MB BCache
> > PYXIS ASIC Pass 257
> >
> > MEMORY
> >
> >
> > Memory Size = 640Mb
> >
> > Bank      Size/Sets   Base Addr
> > ------    ----------  ---------
> >    0        512Mb      00000000
> >    1         64Mb      20000000
> >    2         64Mb      24000000
> >
> >
> > BCache Size = 2Mb
> >
> > Tested Memory =  640Mbytes
> >
> > PCI Bus
> >      Bus 00  Slot 03: Digital Semiconductor 21143 Network Controller
> >                                    ewa0.0.0.3.0          00-00-F8-75-AF-31
> >
> >      Bus 00  Slot 04: PCI IDE
> >                                    pqa0.0.0.4.0          PCI EIDE
> >                                    dka0.0.0.4.0           TOSHIBA CD-ROM
> XM-61
> >
> >      Bus 00  Slot 07: Intel SIO 82378
> >
> >
> >      Bus 00  Slot 20: DECchip 21052 PCI to PCI Bridge
> >        Bus 01  Slot 08: Digital ZLXp Graphics Controller
> >        Bus 01  Slot 09: ISP1040 Scsi Controller
> >                                    pkc0.7.0.1009.0       SCSI Bus ID 7
> >                                    dkc0.0.0.1009.0        QUANTUM
> ATLAS10K2-TY
> >
> >        Bus 01 Slot 10: Vendor: 10b7 Device: 9055 Sub_id: 905510b7
> > ISA
> > Slot    Device  Name            Type         Enabled  BaseAddr  IRQ     DMA
> > 0
> >         0       MOUSE           Embedded        Yes     60      12
> >         1       KBD             Embedded        Yes     60      1
> >         2       COM1            Embedded        Yes     3f8     4
> >         3       COM2            Embedded        Yes     2f8     3
> >         4       LPT1            Embedded        Yes     3bc     7
> >         5       FLOPPY          Embedded        Yes     3f0     6       2
> >         6       EIDE            Embedded        Yes     1f0     14
> >                                                         3f6     15
> >                                                         170
> >                                                         376
> >         7       ES1888          Embedded        Yes     220     5       1
> > >>>show
> > adv_diag                off
> > auto_action             BOOT
> > boot_dev                dka0.0.0.4.0
> > boot_file
> > boot_osflags            a
> > boot_reset              OFF
> > bootdef_dev             dkc0.0.0.1009.0
> > booted_dev              dka0.0.0.4.0
> > booted_file
> > booted_osflags          a
> > char_set                0
> > console                 graphics
> > controlp                on
> > d_bell                  off
> > d_cleanup               on
> > d_complete              off
> > d_eop                   off
> > d_group                 field
> > d_harderr               halt
> > d_loghard               on
> > d_logsoft               off
> > d_oper                  off
> > d_passes                1
> > d_quick                 off
> > d_report                full
> > d_runtime               0
> > d_softerr               continue
> > d_startup               off
> > d_status                off
> > d_trace                 off
> > dma_prefetch            ON
> > dump_dev
> > enable_audit            ON
> > ewa0_arp_tries          3
> > ewa0_bootp_file
> > ewa0_bootp_server
> > ewa0_bootp_tries        3
> > ewa0_def_ginetaddr      0.0.0.0
> > ewa0_def_inetaddr       0.0.0.0
> > ewa0_def_inetfile
> > ewa0_def_sinetaddr      0.0.0.0
> > ewa0_def_subnetmask     0.0.0.0
> > ewa0_ginetaddr          0.0.0.0
> > ewa0_inet_init          bootp
> > ewa0_inetaddr           0.0.0.0
> > ewa0_inetfile
> > ewa0_loop_count         3e8
> > ewa0_loop_inc           a
> > ewa0_loop_patt          ffffffff
> > ewa0_loop_size          2e
> > ewa0_lp_msg_node        1
> > ewa0_mode               Twisted-Pair
> > ewa0_protocols          BOOTP
> > ewa0_sinetaddr          0.0.0.0
> > ewa0_tftp_tries         3
> > ffauto                  OFF
> > ffnext                  OFF
> > graphics_page           0
> > graphics_type           VIDEO
> > kbd_hardware_type       PCXAL
> > language                36
> > language_name           English(American)
> > license                 MU
> > mop_debug               OFF
> > mop_password            00-00000000-00000000
> > mop_version             1
> > mopv3_boot              OFF
> > os_type                 UNIX
> > pal                     OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode
> V1.22-18
> > pci_device_override     0
> > pci_parity              off
> > pkc0_host_id            7
> > pkc0_mode               ultra
> > pkc0_soft_term          diff
> > quick_start             OFF
> > scsi_poll               ON
> > srm2ctrl
> > srm2dev
> > sys_serial_num
> > tt_allow_login          1
> > tta0_page               0
> > tta0_type               VIDEO
> > tty_dev                 0
> > version                 V7.2-1 Mar  6 2000 14:47:02
> > >>>
> >
> >
> >
> > Thanks for looking at this.
> >
> > Ben Nash
> > benash@eecs.umich.edu
> >
> >
> >
> > _______________________________________________
> > freebsd-alpha@freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-alpha
> > To unsubscribe, send any mail to "freebsd-alpha-unsubscribe@freebsd.org"
> --- end of quoted text ---
>
> --
> Wilko Bulte				wilko@FreeBSD.org
>






Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1115247645.4279541da60e0>