Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 27 Apr 2011 15:06:26 +0300
From:      =?iso-8859-7?B?xOfs5/Tx/PDv9evv8iDT8P3x7/I=?= <sdimitr@otenet.gr>
To:        <freebsd-questions@freebsd.org>
Subject:   FreeBSD 8.2 AHCI Timeouts
Message-ID:  <000001cc04d3$8ac15b80$a0441280$@gr>

Next in thread | Raw E-Mail | Index | Archive | Help
Hello all,

 

I'm a new Unix user and I'm having the same problem with the user below.
I've bought the same netbook (Toshiba NB250) and tried to install the
FreeBSD i386 distribution. 

 

Please let me know if you need further information.

 

Thanks in advance for your reply.

                

 

Dimitropoulos Spiros

 

 

 

 



FreeBSD 8.1 AHCI Timeouts


Mak Kolybabi
<mailto:freebsd-questions%40freebsd.org?Subject=FreeBSD%208.1%20AHCI%20Timeo
uts&In-Reply-To=> mak at kolybabi.com 
Sun Jul 25 05:42:26 UTC 2010 

*	Previous message:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/219245.html>;
searching INDEX in .sh 
*	Next message:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/219246.html>;
TexLive on FreeBSD 8.1 
*	Messages sorted by:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/date.html#21
9239> [ date ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/thread.html#
219239> [ thread ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/subject.html
#219239> [ subject ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/author.html#
219239> [ author ] 

  _____  

I bought a netbook today, and am trying to get FreeBSD 8.1 amd64 
installed on it. As is my custom, I'm trying to back up the default 
system image the device came with. But no matter what I do, FreeBSD 
seems unable to properly interact with the hard drive.
 
The netbook is a Toshiba NB250.
The hard drive is listed by the BIOS as TOSHIBA MK1665GSXV-(S1).
The BIOS version is V1.30.
 
The first thing I did was boot the FreeBSD 8.1 amd64 USB install image, 
move to a fixit session using the live USB filesystem, and try and dd 
the hard drive to a USB stick. When I did that, the dd went terribly 
slow (a few KB a minute, before stalling), while dmesg was printing out:
 > ad0: FAILURE - READ_DMA status=51<READY, DSC, ERROR> error=0 LBA=20530
These DMA failures occur regardless of whether the drive is in 
compatibility or AHCI mode.
 
The next thing I did was boot again, changed the drive to AHCI mode, and 
did a "load ahci.ko" in the bootloader command prompt. The dd caused:
 > ahcich0: Timeout on slot 0
 > ahcich0: is 00000000 cs 00000000 ss 00000000 rs 00000000 tfd 40 serr 
00000000
 
The next thing I did was boot again, with the drive in AHCI mode, and 
did a "load ataahci.ko" in the bootloader command prompt. The dd caused:
 > ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=2048
 
Doing some searches on the Internet for this problem, people often asked 
for verbose dmesg, pciconf, and vmstat output. I have attached them all.
 
Any assistance would be greatly appreciated.
 
-------------- next part --------------
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE #0: Mon Jul 19 02:36:49 UTC 2010
     <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; root at
mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff8127c000.
Preloaded mfs_root "/boot/mfsroot" at 0xffffffff8127c230.
Preloaded elf obj module "/boot/kernel/ahci.ko" at 0xffffffff8127c280.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1662690860 Hz
CPU: Intel(R) Atom(TM) CPU N455   @ 1.66GHz (1662.69-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x106ca  Family = 6  Model = 1c  Stepping =
10
 
Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA
,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
 
Features2=0x40e39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE
>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 1073741824 (1024 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x0000000000099fff, 626688 bytes (153 pages)
0x00000000012aa000 - 0x000000003d7cbfff, 1012015104 bytes (247074 pages)
avail memory = 1004281856 (957 MB)
ACPI APIC Table: <TOSCPL TOSCPL00>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP/HT): APIC ID:  1
x86bios:   IVT 0x000000-0x0004ff at 0xffffff0000000000
x86bios:  SSEG 0x010000-0x01ffff at 0xffffff800000e000
x86bios:  EBDA 0x09d000-0x09ffff at 0xffffff000009d000
x86bios:   ROM 0x0a0000-0x0effff at 0xffffff00000a0000
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP 0xf7ca0 00024 (v2 TOSCPL)
ACPI: XSDT 0x3f5d7ae1 00074 (v1 TOSCPL TOSCPL00 06040000  LTP 00000000)
ACPI: FACP 0x3f5dfc60 000F4 (v3 TOSCPL TOSCPL00 06040000 PTL  00000002)
ACPI: DSDT 0x3f5d8c77 06F75 (v1 TOSCPL TOSCPL00 06040000 MSFT 03000000)
ACPI: FACS 0x3f5e2fc0 00040
ACPI: TCPA 0x3f5dfd54 00032 (v1 Phoeni  x       06040000  TL  00000000)
ACPI: HPET 0x3f5dfd86 00038 (v1 DELL   M09      06040000 LOHR 0000005A)
ACPI: MCFG 0x3f5dfdbe 0003C (v1 INTEL  CRESTLNE 06040000 LOHR 0000005A)
ACPI: SLIC 0x3f5dfdfa 00176 (v1 TOSCPL TOSCPL00 06040000 LOHR 00000000)
ACPI: APIC 0x3f5dff70 00068 (v1 TOSCPL TOSCPL00 06040000  LTP 00000000)
ACPI: BOOT 0x3f5dffd8 00028 (v1 TOSCPL TOSCPL00 06040000  LTP 00000001)
ACPI: SSDT 0x3f5d80d7 0025F (v1  PmRef  Cpu0Tst 00003000 INTL 20050624)
ACPI: SSDT 0x3f5d8031 000A6 (v1  PmRef  Cpu1Tst 00003000 INTL 20050624)
ACPI: SSDT 0x3f5d7b55 004DC (v2  PmRef    CpuPm 00003000 INTL 20050624)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00000200 err: 0x000000f0 pmc: 0x00010400
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
null: <null device, zero device>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <TOSCPL TOSCPL00> on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.MPCE -> bus 0 dev 0 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xffffff8000003000 pa 0x4000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.REGS -> bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.IGD0.IGDP -> bus 0 dev 2 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.REGS -> bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.MMTO -> bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.PIRX -> bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.LPC0.PIRY -> bus 0 dev 31 func 0
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
ACPI: SSDT 0x3f5d89a0 00203 (v2  PmRef  Cpu0Ist 00003000 INTL 20050624)
ACPI: SSDT 0x3f5d8336 005E5 (v2  PmRef  Cpu0Cst 00003001 INTL 20050624)
cpu1: <ACPI CPU> on acpi0
ACPI: SSDT 0x3f5d8ba3 000D4 (v2  PmRef  Cpu1Ist 00003000 INTL 20050624)
ACPI: SSDT 0x3f5d891b 00085 (v2  PmRef  Cpu1Cst 00003000 INTL 20050624)
acpi_ec0: <Embedded Controller: GPE 0x19> port 0x62,0x66 on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    7   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0    7   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   11   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    5   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0    5   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   10   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   10   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 6 7 10 11 12 14 15
  Validation          0   11   N     0  3 4 5 6 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 6 7 10 11 12 14 15
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
64-bit
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->  vendor=0x8086, dev=0xa010, revid=0x00
         domain=0, bus=0, slot=0, func=0
         class=06-00-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->  vendor=0x8086, dev=0xa011, revid=0x00
         domain=0, bus=0, slot=2, func=0
         class=03-00-00, hdrtype=0x00, mfdev=1
         cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=7
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message
         map[10]: type Memory, range 32, base 0xf0200000, size 19, enabled
         map[14]: type I/O Port, range 32, base 0x18d0, size  3, enabled
         map[18]: type Prefetchable Memory, range 32, base 0xd0000000, size
28, enabled
         map[1c]: type Memory, range 32, base 0xf0000000, size 20, enabled
pcib0: matched entry for 0.2.INTA
pcib0: slot 2 INTA hardwired to IRQ 16
found->  vendor=0x8086, dev=0xa012, revid=0x00
         domain=0, bus=0, slot=2, func=1
         class=03-80-00, hdrtype=0x00, mfdev=1
         cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         powerspec 2  supports D0 D3  current D0
         map[10]: type Memory, range 32, base 0xf0280000, size 19, enabled
found->  vendor=0x8086, dev=0x27d8, revid=0x02
         domain=0, bus=0, slot=27, func=0
         class=04-03-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=10
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message, 64 bit
         map[10]: type Memory, range 64, base 0xf0500000, size 14, enabled
pcib0: matched entry for 0.27.INTA
pcib0: slot 27 INTA hardwired to IRQ 22
found->  vendor=0x8086, dev=0x27d0, revid=0x02
         domain=0, bus=0, slot=28, func=0
         class=06-04-00, hdrtype=0x01, mfdev=1
         cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=7
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found->  vendor=0x8086, dev=0x27d2, revid=0x02
         domain=0, bus=0, slot=28, func=1
         class=06-04-00, hdrtype=0x01, mfdev=1
         cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
         intpin=b, irq=11
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 17
found->  vendor=0x8086, dev=0x27d4, revid=0x02
         domain=0, bus=0, slot=28, func=2
         class=06-04-00, hdrtype=0x01, mfdev=1
         cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
         intpin=c, irq=5
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message
pcib0: matched entry for 0.28.INTC
pcib0: slot 28 INTC hardwired to IRQ 18
found->  vendor=0x8086, dev=0x27c8, revid=0x02
         domain=0, bus=0, slot=29, func=0
         class=0c-03-00, hdrtype=0x00, mfdev=1
         cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=11
         map[20]: type I/O Port, range 32, base 0x1820, size  5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1820
found->  vendor=0x8086, dev=0x27c9, revid=0x02
         domain=0, bus=0, slot=29, func=1
         class=0c-03-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=b, irq=10
         map[20]: type I/O Port, range 32, base 0x1840, size  5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 19
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1840
found->  vendor=0x8086, dev=0x27ca, revid=0x02
         domain=0, bus=0, slot=29, func=2
         class=0c-03-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=c, irq=5
         map[20]: type I/O Port, range 32, base 0x1860, size  5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1860
found->  vendor=0x8086, dev=0x27cb, revid=0x02
         domain=0, bus=0, slot=29, func=3
         class=0c-03-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=d, irq=7
         map[20]: type I/O Port, range 32, base 0x1880, size  5, enabled
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 16
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1880
found->  vendor=0x8086, dev=0x27cc, revid=0x02
         domain=0, bus=0, slot=29, func=7
         class=0c-03-20, hdrtype=0x00, mfdev=0
         cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=11
         powerspec 2  supports D0 D3  current D0
         map[10]: type Memory, range 32, base 0xf0504000, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xf0504000
found->  vendor=0x8086, dev=0x2448, revid=0xe2
         domain=0, bus=0, slot=30, func=0
         class=06-04-01, hdrtype=0x01, mfdev=0
         cmdreg=0x0005, statreg=0x0010, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->  vendor=0x8086, dev=0x27bc, revid=0x02
         domain=0, bus=0, slot=31, func=0
         class=06-01-00, hdrtype=0x00, mfdev=1
         cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->  vendor=0x8086, dev=0x27c1, revid=0x02
         domain=0, bus=0, slot=31, func=2
         class=01-06-01, hdrtype=0x00, mfdev=0
         cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=b, irq=10
         powerspec 2  supports D0 D3  current D0
         MSI supports 1 message
         map[10]: type I/O Port, range 32, base 0x18e8, size  3, enabled
         map[14]: type I/O Port, range 32, base 0x18dc, size  2, enabled
         map[18]: type I/O Port, range 32, base 0x18e0, size  3, enabled
         map[1c]: type I/O Port, range 32, base 0x18d8, size  2, enabled
         map[20]: type I/O Port, range 32, base 0x18c0, size  4, enabled
         map[24]: type Memory, range 32, base 0xf0504400, size 10, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 19
found->  vendor=0x8086, dev=0x27da, revid=0x02
         domain=0, bus=0, slot=31, func=3
         class=0c-05-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=b, irq=10
         map[20]: type I/O Port, range 32, base 0x18a0, size  5, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 19
vgapci0: <VGA-compatible display> port 0x18d0-0x18d7 mem
0xf0200000-0xf027ffff,0xd0000000-0xdfffffff,0xf0000000-0xf00fffff irq 16 at
device 2.0 on pci0
agp0: <Intel Pineview (M) SVGA controller> on vgapci0
vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0xd0000000
vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xf0200000
vgapci0: Reserved 0x100000 bytes for rid 0x1c type 3 at 0xf0000000
agp0: detected 8188k stolen memory
agp0: aperture size is 256M
vgapci1: <VGA-compatible display> mem 0xf0280000-0xf02fffff at device 2.1 on
pci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     5
pcib1:   subordinate bus   5
pcib1:   I/O decode        0x0-0x0
pcib1:   no prefetched decode
pci5: <ACPI PCI bus> on pcib1
pci5: domain=0, physical bus=5
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pcib2:   domain            0
pcib2:   secondary bus     7
pcib2:   subordinate bus   7
pcib2:   I/O decode        0xf000-0xfff
pcib2:   memory decode     0xf0100000-0xf01fffff
pcib2:   no prefetched decode
pci7: <ACPI PCI bus> on pcib2
pci7: domain=0, physical bus=7
found->  vendor=0x168c, dev=0x002b, revid=0x01
         domain=0, bus=7, slot=0, func=0
         class=02-80-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=11
         powerspec 3  supports D0 D1 D3  current D0
         MSI supports 1 message
         map[10]: type Memory, range 64, base 0xf0100000, size 16, enabled
pcib2: requested memory range 0xf0100000-0xf010ffff: good
pcib2: matched entry for 7.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 17
ath0: <Atheros 9285> mem 0xf0100000-0xf010ffff irq 17 at device 0.0 on pci7
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf0100000
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 49
ath0: [MPSAFE]
ath0: [ITHREAD]
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps
36Mbps 48Mbps 54Mbps
ath0: 11ng MCS: 15Mbps 30Mbps 45Mbps 60Mbps 90Mbps 120Mbps 135Mbps 150Mbps
30Mbps 60Mbps 90Mbps 120Mbps 180Mbps 240Mbps 270Mbps 300Mbps
ath0: AR9285 mac 192.2 RF5133 phy 14.0
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
ath0: using multicast key search
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pcib3:   domain            0
pcib3:   secondary bus     9
pcib3:   subordinate bus   9
pcib3:   I/O decode        0x2000-0x2fff
pcib3:   prefetched decode 0xf0500000-0xf05fffff
pci9: <ACPI PCI bus> on pcib3
pci9: domain=0, physical bus=9
found->  vendor=0x10ec, dev=0x8136, revid=0x05
         domain=0, bus=9, slot=0, func=0
         class=02-00-00, hdrtype=0x00, mfdev=0
         cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
         intpin=a, irq=5
         powerspec 3  supports D0 D1 D2 D3  current D0
         MSI supports 1 message, 64 bit
         MSI-X supports 4 messages in map 0x20
         map[10]: type I/O Port, range 32, base 0x2000, size  8, enabled
pcib3: requested I/O range 0x2000-0x20ff: in range
         map[18]: type Prefetchable Memory, range 64, base 0xf050c000, size
12, enabled
pcib3: requested memory range 0xf050c000-0xf050cfff: good
         map[20]: type Prefetchable Memory, range 64, base 0xf0508000, size
14, enabled
pcib3: requested memory range 0xf0508000-0xf050bfff: good
pcib3: matched entry for 9.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 18
re0: <RealTek 8101E/8102E/8102EL/8103E PCIe 10/100baseTX> port 0x2000-0x20ff
mem 0xf050c000-0xf050cfff,0xf0508000-0xf050bfff irq 18 at device 0.0 on pci9
re0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xf050c000
re0: MSI count : 1
re0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 50
re0: using IRQ 256 for MSI
re0: Using 1 MSI messages
re0: Chip rev. 0x2c000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
re0: bpf attached
re0: Ethernet address: 88:ae:1d:46:55:36
re0: [MPSAFE]
re0: [FILTER]
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0x1820-0x183f irq 23
at device 29.0 on pci0
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 51
uhci0: [MPSAFE]
uhci0: [ITHREAD]
usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0x1840-0x185f irq 19
at device 29.1 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 52
uhci1: [MPSAFE]
uhci1: [ITHREAD]
usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0x1860-0x187f irq 18
at device 29.2 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 53
uhci2: [MPSAFE]
uhci2: [ITHREAD]
usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0x1880-0x189f irq 16
at device 29.3 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 54
uhci3: [MPSAFE]
uhci3: [ITHREAD]
usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xf0504000-0xf05043ff
irq 23 at device 29.7 on pci0
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib4:   domain            0
pcib4:   secondary bus     17
pcib4:   subordinate bus   17
pcib4:   I/O decode        0xf000-0xfff
pcib4:   no prefetched decode
pcib4:   Subtractively decoded bridge.
pci17: <ACPI PCI bus> on pcib4
pci17: domain=0, physical bus=17
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel ICH7 AHCI SATA controller> port
0x18e8-0x18ef,0x18dc-0x18df,0x18e0-0x18e7,0x18d8-0x18db,0x18c0-0x18cf mem
0xf0504400-0xf05047ff irq 19 at device 31.2 on pci0
ahci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xf0504400
ahci0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 55
ahci0: using IRQ 257 for MSI
ahci0: [MPSAFE]
ahci0: [ITHREAD]
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
ahci0: Caps: 64bit NCQ ALP AL CLO 3Gbps PMD SSC PSC 32cmd 4ports
ahci0: Caps2:
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich0: [MPSAFE]
ahcich0: [ITHREAD]
ahcich0: Caps:
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich1: [MPSAFE]
ahcich1: [ITHREAD]
ahcich1: Caps:
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich2: [MPSAFE]
ahcich2: [ITHREAD]
ahcich2: Caps:
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich3: [MPSAFE]
ahcich3: [ITHREAD]
ahcich3: Caps:
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 56
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 57
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
ex_isa_identify()
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xce000-0xcefff,0xdc000-0xdffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
isa_probe_children: probing PnP devices
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 83134550 Hz
Timecounter "TSC" frequency 1662690860 Hz quality -100
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
hptrr: no controller detected.
ahcich0: AHCI reset...
ahcich0: SATA connect time=0ms status=00000123
ahcich0: ready wait time=0ms
ahcich0: AHCI reset done: device found
ahcich1: AHCI reset...
ahcich1: SATA offline status=00000004
ahcich1: AHCI reset done: phy reset found no device
ahcich2: AHCI reset...
ahcich2: SATA offline status=00000004
ahcich2: AHCI reset done: phy reset found no device
ahcich3: AHCI reset...
ahcich3: SATA offline status=00000004
ahcich3: AHCI reset done: phy reset found no device
(aprobe0:ahcich0:0:0:0): SIGNATURE: 0000
md0: Preloaded image </boot/mfsroot> 4194304 bytes at
0xffffffff80e6aa98usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
 
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <TOSHIBA MK1665GSXV GH011M> ATA-8 SATA 2.x device
ada0: Serial Number 50KBB02ZB
ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
pass0 at ahcich0 bus 0 scbus0 target 0 lun 0
pass0: <TOSHIBA MK1665GSXV GH011M> ATA-8 SATA 2.x device
pass0: Serial Number 50KBB02ZB
pass0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
pass0: Command Queueing enabled
acpi_acad0: acline initialization start
battery0: battery initialization start
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
GEOM: new disk ada0
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
GEOM: ada0: partition 4 does not start on a track boundary.
GEOM: ada0: partition 4 does not end on a track boundary.
GEOM: ada0: partition 3 does not start on a track boundary.
GEOM: ada0: partition 3 does not end on a track boundary.
GEOM: ada0: partition 2 does not start on a track boundary.
GEOM: ada0: partition 2 does not end on a track boundary.
GEOM: ada0: partition 1 does not start on a track boundary.
GEOM: ada0: partition 1 does not end on a track boundary.
uhub4: 8 ports with 8 removable, self powered
ugen4.2: <Generic> at usbus4
umass0: <Bulk-In, Bulk-Out, Interface> on usbus4
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:4:0:-1: Attached to scbus4
(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:umass-sim0:0:0:0): SCSI status error
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not
present)
(probe0:umass-sim0:0:0:0): Error 6, Unretryable error
pass1 at umass-sim0 bus 0 scbus4 target 0 lun 0
pass1: <Generic- Multi-Card 1.00> Removable Direct Access SCSI-0 device 
pass1: Serial Number 20090516388200000
pass1: 40.000MB/s transfers
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
da0 at umass-sim0 bus 0 scbus4 target 0 lun 0
da0: <Generic- Multi-Card 1.00> Removable Direct Access SCSI-0 device 
da0: Serial Number 20090516388200000
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
ugen4.3: <CBM> at usbus4
umass1: <CBM Flash Disk, class 0/0, rev 2.00/1.00, addr 3> on usbus4
umass1:  SCSI over Bulk-Only; quirks = 0x4000
umass1:5:1:-1: Attached to scbus5
pass2 at umass-sim1 bus 1 scbus5 target 0 lun 0
pass2: <CBM Flash Disk 5.00> Removable Direct Access SCSI-2 device 
pass2: Serial Number 2821200085074C11
pass2: 40.000MB/s transfers
da1 at umass-sim1 bus 1 scbus5 target 0 lun 0
da1: <CBM Flash Disk 5.00> Removable Direct Access SCSI-2 device 
da1: Serial Number 2821200085074C11
da1: 40.000MB/s transfers
da1: 1985MB (4065280 512 byte sectors: 255H 63S/T 253C)
ugen4.4: <SuYin> at usbus4
ahcich0: Timeout on slot 0
ahcich0: is 00000000 cs 00000000 ss 00000000 rs 00000001 tfd 40 serr
00000000
ahcich0: AHCI reset...
ahcich0: SATA connect time=0ms status=00000123
ahcich0: ready wait time=0ms
ahcich0: AHCI reset done: device found
(ada0:ahcich0:0:0:0): Command timed out
(ada0:ahcich0:0:0:0): Retrying command
GEOM: new disk da0
GEOM: new disk da1
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
GEOM: da1: media size does not match label.
Trying to mount root from ufs:/dev/md0
ct_to_ts([2010-07-25 12:44:09]) = 1280061849.000000000
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /rescue/init
start_init: trying /stand/sysinstall
battery0: battery initialization failed, giving up
ugen4.5: <SanDisk> at usbus4
umass2: <SanDisk Cruzer Micro, class 0/0, rev 2.00/2.00, addr 5> on usbus4
umass2:  SCSI over Bulk-Only; quirks = 0x0000
umass2:6:2:-1: Attached to scbus6
(probe0:umass-sim2:2:0:0): Down reving Protocol Version from 2 to 0?
(probe0:umass-sim2:2:0:0): SCSI status error
(probe0:umass-sim2:2:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim2:2:0:0): CAM status: SCSI Status Error
(probe0:umass-sim2:2:0:0): SCSI status: Check Condition
(probe0:umass-sim2:2:0:0): SCSI sense: UNIT ATTENTION asc:3a,0 (Medium not
present)
(probe0:umass-sim2:2:0:0): Retrying command (per sense data)
pass3 at umass-sim2 bus 2 scbus6 target 0 lun 0
pass3: <SanDisk Cruzer Micro 8.02> Removable Direct Access SCSI-0 device 
pass3: Serial Number 35145307E35347F3
pass3: 40.000MB/s transfers
GEOM: new disk da2
da2 at umass-sim2 bus 2 scbus6 target 0 lun 0
da2: <SanDisk Cruzer Micro 8.02> Removable Direct Access SCSI-0 device 
da2: Serial Number 35145307E35347F3
da2: 40.000MB/s transfers
da2: 7663MB (15695871 512 byte sectors: 255H 63S/T 977C)
GEOM: da2s1: geometry does not match label (128h,63s != 255h,63s).
ugen4.5: <SanDisk> at usbus4 (disconnected)
umass2: at uhub4, port 1, addr 5 (disconnected)
(da2:umass-sim2:2:0:0): lost device
(da2:umass-sim2:2:0:0): removing device entry
(pass3:umass-sim2:2:0:0): lost device
(pass3:umass-sim2:2:0:0): removing device entry
ugen4.5: <SanDisk> at usbus4
umass2: <SanDisk Cruzer Micro, class 0/0, rev 2.00/2.00, addr 5> on usbus4
umass2:  SCSI over Bulk-Only; quirks = 0x0000
umass2:6:2:-1: Attached to scbus6
(probe0:umass-sim2:2:0:0): Down reving Protocol Version from 2 to 0?
(probe0:umass-sim2:2:0:0): SCSI status error
(probe0:umass-sim2:2:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim2:2:0:0): CAM status: SCSI Status Error
(probe0:umass-sim2:2:0:0): SCSI status: Check Condition
(probe0:umass-sim2:2:0:0): SCSI sense: UNIT ATTENTION asc:3a,0 (Medium not
present)
(probe0:umass-sim2:2:0:0): Retrying command (per sense data)
(probe0:umass-sim2:2:0:0): SCSI status error
(probe0:umass-sim2:2:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim2:2:0:0): CAM status: SCSI Status Error
(probe0:umass-sim2:2:0:0): SCSI status: Check Condition
(probe0:umass-sim2:2:0:0): SCSI sense: UNIT ATTENTION asc:3a,0 (Medium not
present)
(probe0:umass-sim2:2:0:0): Retrying command (per sense data)
pass3 at umass-sim2 bus 2 scbus6 target 0 lun 0
pass3: <SanDisk Cruzer Micro 8.02> Removable Direct Access SCSI-0 device 
pass3: Serial Number 35145307E35347F3
pass3: 40.000MB/s transfers
GEOM: new disk da2
da2 at umass-sim2 bus 2 scbus6 target 0 lun 0
da2: <SanDisk Cruzer Micro 8.02> Removable Direct Access SCSI-0 device 
da2: Serial Number 35145307E35347F3
da2: 40.000MB/s transfers
da2: 7663MB (15695871 512 byte sectors: 255H 63S/T 977C)
ugen4.2: <Generic> at usbus4 (disconnected)
umass0: at uhub4, port 4, addr 2 (disconnected)
(da0:umass-sim0:0:0:0): lost device
(da0:umass-sim0:0:0:0): removing device entry
(pass1:umass-sim0:0:0:0): lost device
(pass1:umass-sim0:0:0:0): removing device entry
ugen4.2: <Generic> at usbus4
umass0: <Bulk-In, Bulk-Out, Interface> on usbus4
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:4:0:-1: Attached to scbus4
(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:umass-sim0:0:0:0): SCSI status error
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not
present)
(probe0:umass-sim0:0:0:0): Error 6, Unretryable error
pass1 at umass-sim0 bus 0 scbus4 target 0 lun 0
pass1: <Generic- Multi-Card 1.00> Removable Direct Access SCSI-0 device 
pass1: Serial Number 20090516388200000
pass1: 40.000MB/s transfers
GEOM: new disk da0
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
da0 at umass-sim0 bus 0 scbus4 target 0 lun 0
da0: <Generic- Multi-Card 1.00> Removable Direct Access SCSI-0 device 
da0: Serial Number 20090516388200000
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
-------------- next part --------------
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; hostb0 at
pci0:0:0:0:     class=0x060000 card=0xff601179 chip=0xa0108086 rev=0x00
hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; vgapci0 at
pci0:0:2:0:    class=0x030000 card=0xff601179 chip=0xa0118086 rev=0x00
hdr=0x00
    class      = display
    subclass   = VGA
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; vgapci1 at
pci0:0:2:1:    class=0x038000 card=0xff601179 chip=0xa0128086 rev=0x00
hdr=0x00
    class      = display
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; none0 at
pci0:0:27:0:     class=0x040300 card=0xff601179 chip=0x27d88086 rev=0x02
hdr=0x00
    class      = multimedia
    subclass   = HDA
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; pcib1 at
pci0:0:28:0:     class=0x060400 card=0xff601179 chip=0x27d08086 rev=0x02
hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; pcib2 at
pci0:0:28:1:     class=0x060400 card=0xff601179 chip=0x27d28086 rev=0x02
hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; pcib3 at
pci0:0:28:2:     class=0x060400 card=0xff601179 chip=0x27d48086 rev=0x02
hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; uhci0 at
pci0:0:29:0:     class=0x0c0300 card=0xff601179 chip=0x27c88086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = USB
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; uhci1 at
pci0:0:29:1:     class=0x0c0300 card=0xff601179 chip=0x27c98086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = USB
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; uhci2 at
pci0:0:29:2:     class=0x0c0300 card=0xff601179 chip=0x27ca8086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = USB
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; uhci3 at
pci0:0:29:3:     class=0x0c0300 card=0xff601179 chip=0x27cb8086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = USB
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; ehci0 at
pci0:0:29:7:     class=0x0c0320 card=0xff601179 chip=0x27cc8086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = USB
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; pcib4 at
pci0:0:30:0:     class=0x060401 card=0xff601179 chip=0x24488086 rev=0xe2
hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; isab0 at
pci0:0:31:0:     class=0x060100 card=0xff601179 chip=0x27bc8086 rev=0x02
hdr=0x00
    class      = bridge
    subclass   = PCI-ISA
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; ahci0 at
pci0:0:31:2:     class=0x010601 card=0xff601179 chip=0x27c18086 rev=0x02
hdr=0x00
    class      = mass storage
    subclass   = SATA
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; none1 at
pci0:0:31:3:     class=0x0c0500 card=0xff601179 chip=0x27da8086 rev=0x02
hdr=0x00
    class      = serial bus
    subclass   = SMBus
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; ath0 at
pci0:7:0:0:       class=0x028000 card=0xe8111113 chip=0x002b168c rev=0x01
hdr=0x00
    class      = network
 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; re0 at
pci0:9:0:0:        class=0x020000 card=0xff601179 chip=0x813610ec rev=0x05
hdr=0x00
    class      = network
    subclass   = ethernet
-------------- next part --------------
interrupt                          total       rate
irq1: atkbd0                        1572          1
irq9: acpi0                          572          0
irq23: uhci0 ehci0                  2111          1
cpu0: timer                      2916673       1999
irq256: re0                         2868          1
irq257: ahci0                        126          0
cpu1: timer                      2916486       1998
Total                            5840408       4003
  _____  


*	Previous message:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/219245.html>;
searching INDEX in .sh 
*	Next message:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/219246.html>;
TexLive on FreeBSD 8.1 
*	Messages sorted by:
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/date.html#21
9239> [ date ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/thread.html#
219239> [ thread ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/subject.html
#219239> [ subject ]
<http://lists.freebsd.org/pipermail/freebsd-questions/2010-July/author.html#
219239> [ author ] 

  _____  

 <http://lists.freebsd.org/mailman/listinfo/freebsd-questions>; More
information about the freebsd-questions mailing list  " 




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?000001cc04d3$8ac15b80$a0441280$>