Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 11 Oct 2004 23:14:33 +0800 (CST)
From:      Tai-hwa Liang <avatar@mmlab.cse.yzu.edu.tw>
To:        freebsd-current@freebsd.org
Subject:   Re: 5.3-BETA5/6.0-CURRENT freeze with dynamic loaded modules
Message-ID:  <0410112311337.77434@www.mmlab.cse.yzu.edu.tw>
In-Reply-To: <04092518423116.97410@www.mmlab.cse.yzu.edu.tw>
References:  <04092518423116.97410@www.mmlab.cse.yzu.edu.tw>

next in thread | previous in thread | raw e-mail | index | archive | help
I can reproduce the same lockup on another motherboard, MSI 865PE Neo2,
with 5.3-BETA7 or 6.0-CURRENT cvsup'ed 10 hours ago.

On Sat, 25 Sep 2004, Tai-hwa Liang wrote:
> Testing platforms: ASUS A7N8X and A7N8X-X, nForce2 chipset
>
>   Vanilla 5.3-BETA4/BETA5 installation booted successfully. However,
> if g_md.ko was loaded in /boot/loader.conf or was loaded manually in
> boot prompt, the system will freeze at "lo0: bpf attached" without
> panic dump.
>
>   -CURRENT kernel seems to boot on both system w/ or w/o apic compiled in
> kernel. However, if usd.ko was loaded by usbd after the kernel is booted,
> the kernel will freeze at "ehci0: [GIANT-LOCKED]." Meanwhile, the OHCI
> version turned out to be corrupted:
>
> ohci1: <OHCI (generic) USB controller> mem 0xee005000-0xee005fff irq 11 at device 2.1 on pci0
> ohci1: [GIANT-LOCKED]
> usb0: OHCI version 15.15, legacy support
> usb0: unsupported OHCI revision
> ohci1: USB init failed
> device_attach: ohci1 attach returned 5
>
>   I have no idea about why the system freeze without dumping core whilst
> loading g_md.ko(in boot prompt or in loader.conf) or usb.ko(by usbd)
> dynamically. It seems that the tentative workaround is to compile md
> device statically and load usb.ko prior before usbd was launched
> such like doing that in /boot/loader.conf.
>
>   Following are the related dmesg with -CURRENT cvsup'ed about 1 day ago.
> apic enabled, no PREEMPTION, SCHED_4BSD, all workaround applied:
>
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD 6.0-CURRENT #0: Thu Sep 23 11:10:15 CST 2004
>     root@tinderbox.localdomain:/usr/src/sys/i386/compile/tinderbox
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc072c000.
> Preloaded elf module "/boot/kernel/umass.ko" at 0xc072c244.
> Preloaded elf module "/boot/kernel/usb.ko" at 0xc072c2f0.
> Preloaded elf module "/boot/modules/if_nv.ko" at 0xc072c398.
> Preloaded elf module "/boot/kernel/miibus.ko" at 0xc072c444.
> Calibrating clock(s) ... i8254 clock: 1193189 Hz
> Timecounter "i8254" frequency 1193189 Hz quality 0
> Calibrating TSC clock ... TSC clock: 2171615263 Hz
> CPU: AMD Athlon(tm) XP 3000+ (2171.62-MHz 686-class CPU)
>   Origin = "AuthenticAMD"  Id = 0x6a0  Stepping = 0
>   Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
>   AMD Features=0xc0400000<AMIE,DSP,3DNow!>
> Data TLB: 32 entries, fully associative
> Instruction TLB: 16 entries, fully associative
> L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
> L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
> L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
> real memory  = 1073676288 (1023 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
> 0x0000000000826000 - 0x000000003edbdfff, 1046052864 bytes (255384 pages)
> avail memory = 1045307392 (996 MB)
> mptable_probe: MP Config Table has bad signature: \^E\^G
> Table 'FACP' at 0x3fff3040
> Table 'APIC' at 0x3fff74c0
> MADT: Found table at 0x3fff74c0
> APIC: Using the MADT enumerator.
> MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
> ACPI APIC Table: <Nvidia AWRDACPI>
> APIC: CPU 0 has ACPI ID 0
> bios32: Found BIOS32 Service Directory header at 0xc00fb000
> bios32: Entry = 0xfb490 (c00fb490)  Rev = 0  Len = 1
> pcibios: PCI BIOS entry at 0xf0000+0xb4c0
> pnpbios: Found PnP BIOS data at 0xc00fbf20
> pnpbios: Entry = f0000:bf50  Rev = 1.0
> Other BIOS signatures found:
> MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
> ioapic0: Routing external 8259A's -> intpin 0
> ioapic0: intpin 0 -> ExtINT (edge, high)
> ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
> ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
> ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
> ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
> ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
> ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
> ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
> ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
> ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
> ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
> ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
> ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
> ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
> ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
> ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
> ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
> ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
> ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
> ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
> ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
> ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
> ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
> ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
> MADT: intr override: source 0, irq 2
> ioapic0: Routing IRQ 0 -> intpin 2
> ioapic0: intpin 2 trigger: edge
> ioapic0: intpin 2 polarity: high
> MADT: intr override: source 9, irq 9
> ioapic0: intpin 9 trigger: level
> ioapic0: intpin 9 polarity: high
> lapic0: Routing NMI -> LINT1
> lapic0: LINT1 trigger: edge
> lapic0: LINT1 polarity: active-high
> ioapic0 <Version 1.1> irqs 0-23 on motherboard
> cpu0 BSP:
>      ID: 0x00000000   VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
>   lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> mem: <memory>
> Pentium Pro MTRR support enabled
> null: <null device, zero device>
> io: <I/O>
> random: <entropy source, Software, Yarrow>
> acpi0: <Nvidia AWRDACPI> on motherboard
> acpi0: [MPSAFE]
> pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000888
> pci_open(1a):	mode1res=0x80000000 (0x80000000)
> pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=01e010de)
> pcibios: BIOS version 2.10
> Found $PIR table, 11 entries at 0xc00fdeb0
> PCI-Only Interrupts: 5 11
> Location  Bus Device Pin  Link  IRQs
> slot 1      0    8    A   0x01  3 4 5 7 9 10 11 12 14 15
> slot 1      0    8    B   0x02  3 4 5 7 9 10 11 12 14 15
> slot 1      0    8    C   0x03  3 4 5 7 9 10 11 12 14 15
> slot 1      0    8    D   0x04  3 4 5 7 9 10 11 12 14 15
> slot 2      0   12    A   0x01  3 4 5 7 9 10 11 12 14 15
> slot 2      0   12    B   0x02  3 4 5 7 9 10 11 12 14 15
> slot 2      0   12    C   0x03  3 4 5 7 9 10 11 12 14 15
> slot 2      0   12    D   0x04  3 4 5 7 9 10 11 12 14 15
> slot 3    255   31    A   0x0f  3 4 5 7 9 10 11 12 14 15
> slot 3    255   31    B   0x0f  3 4 5 7 9 10 11 12 14 15
> slot 3    255   31    C   0x0f  3 4 5 7 9 10 11 12 14 15
> slot 3    255   31    D   0x0f  3 4 5 7 9 10 11 12 14 15
> slot 4      1    6    A   0x01  3 4 5 7 9 10 11 12 14 15
> slot 4      1    6    B   0x02  3 4 5 7 9 10 11 12 14 15
> slot 4      1    6    C   0x03  3 4 5 7 9 10 11 12 14 15
> slot 4      1    6    D   0x04  3 4 5 7 9 10 11 12 14 15
> slot 5      1    7    A   0x04  3 4 5 7 9 10 11 12 14 15
> slot 5      1    7    B   0x01  3 4 5 7 9 10 11 12 14 15
> slot 5      1    7    C   0x02  3 4 5 7 9 10 11 12 14 15
> slot 5      1    7    D   0x03  3 4 5 7 9 10 11 12 14 15
> slot 6      1    8    A   0x03  3 4 5 7 9 10 11 12 14 15
> slot 6      1    8    B   0x04  3 4 5 7 9 10 11 12 14 15
> slot 6      1    8    C   0x01  3 4 5 7 9 10 11 12 14 15
> slot 6      1    8    D   0x02  3 4 5 7 9 10 11 12 14 15
> slot 7      1    9    A   0x02  3 4 5 7 9 10 11 12 14 15
> slot 7      1    9    B   0x03  3 4 5 7 9 10 11 12 14 15
> slot 7      1    9    C   0x04  3 4 5 7 9 10 11 12 14 15
> slot 7      1    9    D   0x01  3 4 5 7 9 10 11 12 14 15
> slot 8      1   10    A   0x01  3 4 5 7 9 10 11 12 14 15
> slot 8      1   10    B   0x02  3 4 5 7 9 10 11 12 14 15
> slot 8      1   10    C   0x03  3 4 5 7 9 10 11 12 14 15
> slot 8      1   10    D   0x04  3 4 5 7 9 10 11 12 14 15
> slot 9      1   11    A   0x03  3 4 5 7 9 10 11 12 14 15
> slot 9      1   11    B   0x03  3 4 5 7 9 10 11 12 14 15
> slot 9      1   11    C   0x03  3 4 5 7 9 10 11 12 14 15
> slot 9      1   11    D   0x03  3 4 5 7 9 10 11 12 14 15
> embedded    0   30    A   0x04  3 4 5 7 9 10 11 12 14 15
> embedded    0   30    B   0x01  3 4 5 7 9 10 11 12 14 15
> embedded    0   30    C   0x02  3 4 5 7 9 10 11 12 14 15
> embedded    0   30    D   0x03  3 4 5 7 9 10 11 12 14 15
> AcpiOsDerivePciId: bus 0 dev 1 func 0
> acpi0: Power Button (fixed)
> AcpiOsDerivePciId: bus 0 dev 1 func 0
> AcpiOsDerivePciId: bus 0 dev 1 func 0
> AcpiOsDerivePciId: bus 0 dev 1 func 0
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 5, width = 2
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> ACPI timer looks GOOD min = 3, max = 4, width = 1
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> ACPI PCI link initial configuration:
> \\_SB_.PCI0.APCS irq  0: [23] 23+ high,level,sharable 0.1.0
> \\_SB_.PCI0.APCS irq  0: [23] 23+ high,level,sharable 0.1.1
> \\_SB_.PCI0.APCF irq  0: [20 21 22]  0+ high,level,sharable 0.2.0
> \\_SB_.PCI0.APCG irq  0: [20 21 22]  0+ high,level,sharable 0.2.1
> \\_SB_.PCI0.APCL irq  0: [20 21 22]  0+ high,level,sharable 0.2.2
> \\_SB_.PCI0.APCH irq  0: [20 21 22]  0+ high,level,sharable 0.4.0
> \\_SB_.PCI0.APCI irq  0: [20 21 22]  0+ high,level,sharable 0.5.0
> \\_SB_.PCI0.APCJ irq  0: [20 21 22]  0+ high,level,sharable 0.6.0
> \\_SB_.PCI0.APCK irq  0: [20 21 22]  0+ high,level,sharable 0.6.1
> \\_SB_.PCI0.APCM irq  0: [20 21 22]  0+ high,level,sharable 0.13.0
> \\_SB_.PCI0.AP3C irq  0: [20 21 22]  0+ high,level,sharable 0.12.0
> \\_SB_.PCI0.APCZ irq  0: [20 21 22]  0+ high,level,sharable 0.9.0
> pci0: <ACPI PCI bus> on pcib0
> pci0: physical bus=0
> 	map[10]: type 3, range 32, base e8000000, size 26, enabled
> found->	vendor=0x10de, dev=0x01e0, revid=0xa2
> 	bus=0, slot=0, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x01eb, revid=0xa2
> 	bus=0, slot=0, func=1
> 	class=05-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x01ee, revid=0xa2
> 	bus=0, slot=0, func=2
> 	class=05-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x01ed, revid=0xa2
> 	bus=0, slot=0, func=3
> 	class=05-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x01ec, revid=0xa2
> 	bus=0, slot=0, func=4
> 	class=05-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x01ef, revid=0xa2
> 	bus=0, slot=0, func=5
> 	class=05-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x10de, dev=0x0060, revid=0xa3
> 	bus=0, slot=1, func=0
> 	class=06-01-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x000f, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	map[10]: type 4, range 32, base 0000d000, size  5, enabled
> pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.APCS)
> pcib0: possible interrupts: 23
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCF (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCG (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCL (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCH (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCI (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCJ (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCK (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCM (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.AP3C (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCZ (references 1, priority 100):
> 	interrupts:	    22    21    20
> 	penalty:	   100   100   100
> \\_SB_.PCI0.APCS (references 2, priority 40):
> 	interrupts:	    23
> 	penalty:	    20
> ioapic0: Changing polarity for pin 23 to high
> pcib0: slot 1 INTA routed to irq 23 via \\_SB_.PCI0.APCS
> found->	vendor=0x10de, dev=0x0064, revid=0xa2
> 	bus=0, slot=1, func=1
> 	class=0c-05-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
> 	intpin=a, irq=23
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type 1, range 32, base ee004000, size 12, enabled
> pcib0: matched entry for 0.2.INTA (src \\_SB_.PCI0.APCF)
> pcib0: possible interrupts: 20 21 22
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCF (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCG (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCL (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCH (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCI (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCJ (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCK (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCM (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.AP3C (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> \\_SB_.PCI0.APCZ (references 1, priority 200):
> 	interrupts:	    22    21    20
> 	penalty:	   200   200   200
> ioapic0: Changing polarity for pin 22 to high
> pcib0: slot 2 INTA routed to irq 22 via \\_SB_.PCI0.APCF
> found->	vendor=0x10de, dev=0x0067, revid=0xa3
> 	bus=0, slot=2, func=0
> 	class=0c-03-10, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
> 	intpin=a, irq=22
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type 1, range 32, base ee005000, size 12, enabled
> pcib0: matched entry for 0.2.INTB (src \\_SB_.PCI0.APCG)
> pcib0: possible interrupts: 20 21 22
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCG (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCL (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCH (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCI (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCJ (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCK (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCM (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.AP3C (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> \\_SB_.PCI0.APCZ (references 1, priority 303):
> 	interrupts:	    21    20    22
> 	penalty:	   300   300   310
> ioapic0: Changing polarity for pin 21 to high
> pcib0: slot 2 INTB routed to irq 21 via \\_SB_.PCI0.APCG
> found->	vendor=0x10de, dev=0x0067, revid=0xa3
> 	bus=0, slot=2, func=1
> 	class=0c-03-10, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
> 	intpin=b, irq=21
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type 1, range 32, base ee000000, size  8, enabled
> pcib0: matched entry for 0.2.INTC (src \\_SB_.PCI0.APCL)
> pcib0: possible interrupts: 20 21 22
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCL (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCH (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCI (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCJ (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCK (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCM (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.AP3C (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> \\_SB_.PCI0.APCZ (references 1, priority 406):
> 	interrupts:	    20    22    21
> 	penalty:	   400   410   410
> ioapic0: Changing polarity for pin 20 to high
> pcib0: slot 2 INTC routed to irq 20 via \\_SB_.PCI0.APCL
> found->	vendor=0x10de, dev=0x0068, revid=0xa3
> 	bus=0, slot=2, func=2
> 	class=0c-03-20, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
> 	intpin=c, irq=20
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type 1, range 32, base ee001000, size 12, enabled
> 	map[14]: type 4, range 32, base 0000d400, size  3, enabled
> pcib0: matched entry for 0.4.INTA (src \\_SB_.PCI0.APCH)
> pcib0: possible interrupts: 20 21 22
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCH (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.APCI (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.APCJ (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.APCK (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.APCM (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.AP3C (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> \\_SB_.PCI0.APCZ (references 1, priority 510):
> 	interrupts:	    22    21    20
> 	penalty:	   510   510   510
> pcib0: slot 4 INTA routed to irq 22 via \\_SB_.PCI0.APCH
> found->	vendor=0x10de, dev=0x0066, revid=0xa1
> 	bus=0, slot=4, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x14 (5000 ns)
> 	intpin=a, irq=22
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type 4, range 32, base 0000d800, size  8, enabled
> 	map[14]: type 4, range 32, base 0000dc00, size  7, enabled
> 	map[18]: type 1, range 32, base ee002000, size 12, enabled
> pcib0: matched entry for 0.6.INTA (src \\_SB_.PCI0.APCJ)
> pcib0: possible interrupts: 20 21 22
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCI (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> \\_SB_.PCI0.APCJ (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> \\_SB_.PCI0.APCK (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> \\_SB_.PCI0.APCM (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> \\_SB_.PCI0.AP3C (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> \\_SB_.PCI0.APCZ (references 1, priority 613):
> 	interrupts:	    21    20    22
> 	penalty:	   610   610   620
> pcib0: slot 6 INTA routed to irq 21 via \\_SB_.PCI0.APCJ
> found->	vendor=0x10de, dev=0x006a, revid=0xa1
> 	bus=0, slot=6, func=0
> 	class=04-01-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
> 	intpin=a, irq=21
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> found->	vendor=0x10de, dev=0x006c, revid=0xa3
> 	bus=0, slot=8, func=0
> 	class=06-04-00, hdrtype=0x01, mfdev=0
> 	cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x02 (500 ns)
> 	map[20]: type 4, range 32, base 0000f000, size  4, enabled
> found->	vendor=0x10de, dev=0x0065, revid=0xa2
> 	bus=0, slot=9, func=0
> 	class=01-01-8a, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
> 	powerspec 2  supports D0 D3  current D0
> found->	vendor=0x10de, dev=0x01e8, revid=0xa2
> 	bus=0, slot=30, func=0
> 	class=06-04-00, hdrtype=0x01, mfdev=0
> 	cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
> 	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
> pci0: <memory, RAM> at device 0.1 (no driver attached)
> pci0: <memory, RAM> at device 0.2 (no driver attached)
> pci0: <memory, RAM> at device 0.3 (no driver attached)
> pci0: <memory, RAM> at device 0.4 (no driver attached)
> pci0: <memory, RAM> at device 0.5 (no driver attached)
> isab0: <PCI-ISA bridge> at device 1.0 on pci0
> isa0: <ISA bus> on isab0
> pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
> ohci0: <OHCI (generic) USB controller> mem 0xee004000-0xee004fff irq 22 at device 2.0 on pci0
> ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xee004000
> ohci0: [GIANT-LOCKED]
> usb0: OHCI version 1.0, legacy support
> usb0: SMM does not respond, resetting
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 3 ports with 3 removable, self powered
> ohci1: <OHCI (generic) USB controller> mem 0xee005000-0xee005fff irq 21 at device 2.1 on pci0
> ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xee005000
> ohci1: [GIANT-LOCKED]
> usb1: OHCI version 1.0, legacy support
> usb1: SMM does not respond, resetting
> usb1: <OHCI (generic) USB controller> on ohci1
> usb1: USB revision 1.0
> uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 3 ports with 3 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xee000000-0xee0000ff irq 20 at device 2.2 on pci0
> ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xee000000
> ehci0: [GIANT-LOCKED]
> ehci_pci_attach: companion usb0
> ehci_pci_attach: companion usb1
> usb2: EHCI version 1.0
> usb2: companion controllers, 4 ports each: usb0 usb1
> usb2: <EHCI (generic) USB 2.0 controller> on ehci0
> usb2: USB revision 2.0
> uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub2: 6 ports with 6 removable, self powered
> nv0: <NVIDIA nForce MCP2 Networking Adapter> port 0xd400-0xd407 mem 0xee001000-0xee001fff irq 22 at device 4.0 on pci0
> nv0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xee001000
> nv0: Ethernet address 00:e0:18:eb:15:ed
> miibus0: <MII bus> on nv0
> rlphy0: <RTL8201L 10/100 media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> nv0: bpf attached
> nv0: Ethernet address: 00:e0:18:eb:15:ed
> nv0: [GIANT-LOCKED]
> pci0: <multimedia, audio> at device 6.0 (no driver attached)
> pcib1: <ACPI PCI-PCI bridge> at device 8.0 on pci0
> pcib1:   secondary bus     1
> pcib1:   subordinate bus   1
> pcib1:   I/O decode        0xf000-0xfff
> pcib1:   memory decode     0xfff00000-0xfffff
> pcib1:   prefetched decode 0xfff00000-0xfffff
> ACPI PCI link initial configuration:
> \\_SB_.PCI0.APC1 irq  0: [16] 16+ high,level,sharable 1.6.0
> \\_SB_.PCI0.APC2 irq  0: [17] 17+ high,level,sharable 1.6.1
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.6.2
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 1.6.3
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 1.7.0
> \\_SB_.PCI0.APC1 irq  0: [16] 16+ high,level,sharable 1.7.1
> \\_SB_.PCI0.APC2 irq  0: [17] 17+ high,level,sharable 1.7.2
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.7.3
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.8.0
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 1.8.1
> \\_SB_.PCI0.APC1 irq  0: [16] 16+ high,level,sharable 1.8.2
> \\_SB_.PCI0.APC2 irq  0: [17] 17+ high,level,sharable 1.8.3
> \\_SB_.PCI0.APC2 irq  0: [17] 17+ high,level,sharable 1.9.0
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.9.1
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 1.9.2
> \\_SB_.PCI0.APC1 irq  0: [16] 16+ high,level,sharable 1.9.3
> \\_SB_.PCI0.APC1 irq  0: [16] 16+ high,level,sharable 1.10.0
> \\_SB_.PCI0.APC2 irq  0: [17] 17+ high,level,sharable 1.10.1
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.10.2
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 1.10.3
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.11.0
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.11.1
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.11.2
> \\_SB_.PCI0.APC3 irq  0: [18] 18+ high,level,sharable 1.11.3
> pci1: <ACPI PCI bus> on pcib1
> pci1: physical bus=1
> atapci0: <nVidia nForce2 UDMA133 controller> port 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 9.0 on pci0
> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
> ata0: channel #0 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> ata0: reset tp1 mask=03 ostat0=50 ostat1=00
> ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
> ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
> ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
> ata0: [MPSAFE]
> ata1: channel #1 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> ata1: reset tp1 mask=03 ostat0=50 ostat1=01
> ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
> ata1-slave:  stat=0x00 err=0x01 lsb=0x7f msb=0x7f
> ata1: reset tp2 stat0=10 stat1=00 devices=0x4<ATAPI_MASTER>
> ata1: [MPSAFE]
> pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pcib2:   secondary bus     2
> pcib2:   subordinate bus   2
> pcib2:   I/O decode        0xf000-0xfff
> pcib2:   memory decode     0xec000000-0xedffffff
> pcib2:   prefetched decode 0xe0000000-0xe7ffffff
> AcpiOsDerivePciId: bus 0 dev 30 func 0
> ACPI PCI link initial configuration:
> \\_SB_.PCI0.APC4 irq  0: [19] 19+ high,level,sharable 2.0.0
> pci2: <ACPI PCI bus> on pcib2
> pci2: physical bus=2
> 	map[10]: type 1, range 32, base ec000000, size 24, enabled
> pcib2: device (null) requested decoded memory range 0xec000000-0xecffffff
> 	map[14]: type 3, range 32, base e0000000, size 27, enabled
> pcib2: device (null) requested decoded memory range 0xe0000000-0xe7ffffff
> pcib2: matched entry for 2.0.INTA (src \\_SB_.PCI0.APC4)
> pcib2: possible interrupts: 19
> ACPI PCI link arbitrated settings:
> \\_SB_.PCI0.APCI (references 1, priority 616):
> 	interrupts:	    20    22    21
> 	penalty:	   610   620   620
> \\_SB_.PCI0.APCK (references 1, priority 616):
> 	interrupts:	    20    22    21
> 	penalty:	   610   620   620
> \\_SB_.PCI0.APCM (references 1, priority 616):
> 	interrupts:	    20    22    21
> 	penalty:	   610   620   620
> \\_SB_.PCI0.AP3C (references 1, priority 616):
> 	interrupts:	    20    22    21
> 	penalty:	   610   620   620
> \\_SB_.PCI0.APCZ (references 1, priority 616):
> 	interrupts:	    20    22    21
> 	penalty:	   610   620   620
> \\_SB_.PCI0.APC4 (references 6, priority 120):
> 	interrupts:	    19
> 	penalty:	    20
> \\_SB_.PCI0.APC1 (references 5, priority 0):
> 	interrupts:	     0
> 	penalty:	100000
> \\_SB_.PCI0.APC2 (references 5, priority 0):
> 	interrupts:	     0
> 	penalty:	100000
> \\_SB_.PCI0.APC3 (references 9, priority 0):
> 	interrupts:	     0
> 	penalty:	100000
> ioapic0: Changing polarity for pin 19 to high
> pcib2: slot 0 INTA routed to irq 19 via \\_SB_.PCI0.APC4
> found->	vendor=0x10de, dev=0x0110, revid=0xb2
> 	bus=2, slot=0, func=0
> 	class=03-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
> 	lattimer=0x20 (960 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
> 	intpin=a, irq=19
> 	powerspec 2  supports D0 D3  current D0
> pci2: <display, VGA> at device 0.0 (no driver attached)
> fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
> fdc0: ic_type 90 part_id 80
> fdc0: [MPSAFE]
> fdc0: [FAST]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> sio0: irq maps: 0x821 0x831 0x821 0x821
> sio0 port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1: irq maps: 0x821 0x829 0x821 0x821
> sio1 port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> unknown: not probed (disabled)
> unknown: not probed (disabled)
> ppc0: using extended I/O port range
> ppc0: ECP SPP ECP+EPP SPP
> ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/16 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> plip0: bpf attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> psmcpnp0 irq 12 on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0047
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
> atkbd0: [GIANT-LOCKED]
> psm0: current command byte:0047
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: model IntelliMouse, device ID 3-00, 3 buttons
> psm0: config:00000000, flags:00000008, packet size:4
> psm0: syncmask:08, syncbits:00
> unknown: not probed (disabled)
> unknown: not probed (disabled)
> npx0: [FAST]
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> atkbdc: atkbdc0 already exists; skipping it
> fdc: fdc0 already exists; skipping it
> ppc: ppc0 already exists; skipping it
> sio: sio0 already exists; skipping it
> sio: sio1 already exists; skipping it
> Trying Read_Port at 203
> Trying Read_Port at 243
> Trying Read_Port at 283
> Trying Read_Port at 2c3
> Trying Read_Port at 303
> Trying Read_Port at 343
> Trying Read_Port at 383
> Trying Read_Port at 3c3
> sc: sc0 already exists; skipping it
> vga: vga0 already exists; skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROMs> at iomem 0xd4000-0xd57ff,0xd0000-0xd3fff,0xc0000-0xcc7ff on isa0
> adv0: not probed (disabled)
> aha0: not probed (disabled)
> aic0: not probed (disabled)
> bt0: not probed (disabled)
> cs0: not probed (disabled)
> ed0: not probed (disabled)
> fe0: not probed (disabled)
> ie0: not probed (disabled)
> lnc0: not probed (disabled)
> pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
> pcic1: not probed (disabled)
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> sn0: not probed (disabled)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> fb0: vga0, vga, type:VGA (5), flags:0x7007f
> fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> fb0: init mode:24, bios mode:3, current mode:24
> fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> VGA parameters upon power-up
> 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80
> bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> VGA parameters in BIOS for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> EGA/VGA parameters to be used for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> vt0: not probed (disabled)
> isa_probe_children: probing PnP devices
> Device configuration finished.
> Timecounter "TSC" frequency 2171615263 Hz quality 800
> Timecounters tick every 10.000 msec
> lo0: bpf attached
> ata0-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin
> ata0-master: setting PIO4 on nVidia nForce2 chip
> ata0-master: setting UDMA133 on nVidia nForce2 chip
> ad0: <Maxtor 6Y120P0/YAR41BW0> ATA-7 disk at ata0-master
> ad0: 117246MB (240121728 sectors), 238216 C, 16 H, 63 S, 512 B
> ad0: 16 secs/int, 1 depth queue, UDMA133
> ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
> ATAPI_RESET time = 50us
> ata1-master: setting PIO4 on nVidia nForce2 chip
> ata1-master: setting UDMA33 on nVidia nForce2 chip
> acd0: <ASUS CD-S520/A5/1.0> CDROM drive at ata1 as master
> acd0: read 687KB/s (8937KB/s), 128KB buffer, UDMA33
> acd0: Reads: CDR, CDRW, CDDA stream, packet
> acd0: Writes:
> acd0: Audio: play, 255 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> (probe0:ata0:0:0:0): error 22
> (probe0:ata0:0:0:0): Unretryable Error
> (probe1:ata0:0:1:0): error 22
> (probe1:ata0:0:1:0): Unretryable Error
> (probe0:ata0:0:0:0): error 22
> (probe0:ata0:0:0:0): Unretryable Error
> (probe1:ata0:0:1:0): error 22
> (probe1:ata0:0:1:0): Unretryable Error
> (probe3:ata1:0:1:0): error 22
> (probe3:ata1:0:1:0): Unretryable Error
> (probe3:ata1:0:1:0): error 22
> (probe3:ata1:0:1:0): Unretryable Error
> (probe2:ata1:0:0:0): error 22
> (probe2:ata1:0:0:0): Unretryable Error
> (probe2:ata1:0:0:0): error 6
> (probe2:ata1:0:0:0): Unretryable Error
> (probe2:ata1:0:0:0): error 22
> (probe2:ata1:0:0:0): Unretryable Error
> pass0 at ata1 bus 0 target 0 lun 0
> pass0: <ASUS CD-S520/A5 1.0> Removable CD-ROM SCSI-0 device
> pass0: 33.000MB/s transfers
> pass0 at ata1 bus 0 target 0 lun 0
> pass0: <ASUS CD-S520/A5 1.0> Removable CD-ROM SCSI-0 device
> pass0: 33.000MB/s transfers
> ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
> ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
> ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
> ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
> ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
> ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
> ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
> ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0
> ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
> ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
> ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
> ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
> ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
> ioapic0: routing intpin 22 (PCI IRQ 22) to cluster 0
> GEOM: new disk ad0
> [0] f:00 typ:12 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:20964762
> [1] f:00 typ:15 s(CHS):1023/255/63 e(CHS):1023/254/63 s:20964825 l:201326580
> [2] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:222291405 l:17816085
> [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> GEOM: Configure ad0s1, start 32256 length 10733958144 end 10733990399
> GEOM: Configure ad0s2, start 10733990400 length 103079208960 end 113813199359
> GEOM: Configure ad0s3, start 113813199360 length 9121835520 end 122935034879
> MBREXT Slice 5 on ad0s2:
> [0] f:00 typ:11 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:201326517
> [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> GEOM: Configure ad0s5, start 32256 length 103079176704 end 103079208959
> GEOM: Configure ad0s3a, start 0 length 268435456 end 268435455
> GEOM: Configure ad0s3b, start 268435456 length 2121048064 end 2389483519
> GEOM: Configure ad0s3c, start 0 length 9121835520 end 9121835519
> GEOM: Configure ad0s3d, start 2389483520 length 16777216 end 2406260735
> GEOM: Configure ad0s3e, start 2406260736 length 1476395008 end 3882655743
> GEOM: Configure ad0s3f, start 3882655744 length 5239179776 end 9121835519
> Mounting root from ufs:/dev/ad0s3a
> start_init: trying /sbin/init
> Linux ELF exec handler installed
> procfs registered
> linprocfs registered



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?0410112311337.77434>