Date: Tue, 01 Jun 2004 15:54:41 -0400 From: "D. Pageau" <dpageau@infodev.ca> To: freebsd-bugs@freebsd.org Subject: Keyboard error IBM xSeries 335 *LONG POST* Message-ID: <40BCDF01.1060600@infodev.ca>
next in thread | raw e-mail | index | archive | help
Keyboard error on IBM xSeries 335 with Freebsd 5.2.1 but work fine with 4.10 The keyboard work well in installation process (floppy install), then I reboot. Keyboard work fine at the boot manager but died as soon FreeBSD is booted. The hardware is IBM xSeries 335. I can confirm that problem with both 5.1 and 5.2.1. The keyboard work flawlessly under Freebsd 4.10 and OpenBSD 3.5. dmesg from 4.9 (working) and 5.2.1 (not working) bellow. *** Freebsd 5.2.1 *** #uname -a FreeBSD trinity3.xxx.xxx. 5.2.1-RELEASE FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004 root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC i386 #dmesg Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004 root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a35000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a351f4. ACPI APIC Table: <IBM SERONYXP> Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.72-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 536788992 (511 MB) avail memory = 511741952 (488 MB) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic2 <Version 1.1> irqs 32-47 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard ioapic0 <Version 1.1> irqs 0-15 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <IBM SERONYXP> on motherboard pcibios: BIOS version 2.10 acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x488-0x48b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib0: slot 15 INTA is routed to irq 11 pci0: <display, VGA> at device 1.0 (no driver attached) atapci0: <ServerWorks CSB5 UDMA100 controller> port 0x700-0x70f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 11 at device 15.2 on pci0 usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered isab0: <PCI-ISA bridge> at device 15.3 on pci0 isa0: <ISA bus> on isab0 pcib1: <ACPI Host-PCI bridge> on acpi0 pci1: <ACPI PCI bus> on pcib1 mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2300-0x23ff mem 0xfbfe0000-0xfbfeffff,0xfbff0000-0xfbffffff irq 22 at device 1.0 on pci1 pcib2: <ACPI Host-PCI bridge> on acpi0 pci2: <ACPI PCI bus> on pcib2 bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf9ff0000-0xf9ffffff irq 24 at device 1.0 on pci2 bge0: Ethernet address: 00:0d:60:1c:8b:64 miibus0: <MII bus> on bge0 brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: unable to set the command byte. device_probe_and_attach: atkbd0 attach returned 6 psm0: unable to set the command byte. fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A orm0: <Option ROMs> at iomem 0xc9800-0xcd7ff,0xc8000-0xc97ff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master PIO4 Waiting 15 seconds for SCSI devices to settle ses0 at mpt0 bus 0 target 8 lun 0 ses0: <IBM 25P3495a S320 1 1> Fixed Processor SCSI-2 device ses0: 3.300MB/s transfers ses0: SAF-TE Compliant Device GEOM: create disk da0 dp=0xc48b9450 da0 at mpt0 bus 0 target 0 lun 0 da0: <IBM-ESXS ST336607LC FN B25F> Fixed Direct Access SCSI-3 device da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 34715MB (71096640 512 byte sectors: 255H 63S/T 4425C) SMP: AP CPU #1 Launched! *** Freebsd 4.10 *** #uname -a FreeBSD trinity3.xxx.xxx. 4.10-RELEASE FreeBSD 4.10-RELEASE #0: Tue May 25 22:47:12 GMT 2004 root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386 #dmesg Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.10-RELEASE #0: Tue May 25 22:47:12 GMT 2004 root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.72-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 536788992 (524208K bytes) avail memory = 516829184 (504716K bytes) Preloaded elf kernel "kernel" at 0xc0551000. Warning: Pentium 4 CPU: PSE disabled Pentium Pro MTRR support enabled md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pci0: <ATI Mach64-GR graphics accelerator> at 1.0 irq 10 atapci0: <ServerWorks CSB5 ATA100 controller> port 0x700-0x70f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 11 at device 15.2 on pci0 usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered isab0: <PCI to ISA bridge (vendor=1166 device=0225)> at device 15.3 on pci0 isa0: <ISA bus> on isab0 pcib1: <Host to PCI bridge> on motherboard pci1: <PCI bus> on pcib1 mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2300-0x23ff mem 0xfbfe0000-0xfbfeffff,0xfbff0000-0xfbffffff irq 9 at device 1.0 on pci1 pcib2: <Host to PCI bridge> on motherboard pci2: <PCI bus> on pcib2 bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf9ff0000-0xf9ffffff irq 3 at device 1.0 on pci2 bge0: Ethernet address: 00:0d:60:1c:8b:64 miibus0: <MII bus> on bge0 brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xf9fe0000-0xf9feffff irq 5 at device 2.0 on pci2 bge1: Ethernet address: 00:0d:60:1c:8b:65 miibus1: <MII bus> on bge1 brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto pcib3: <Host to PCI bridge> on motherboard pci3: <PCI bus> on pcib3 pcib4: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard pci4: <PCI bus> on pcib4 pcib5: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard pci5: <PCI bus> on pcib5 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcd7ff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse Explorer, device ID 4 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: parallel port not found. acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master PIO4 Waiting 15 seconds for SCSI devices to settle pass1 at mpt0 bus 0 target 8 lun 0 pass1: <IBM 25P3495a S320 1 1> Fixed Processor SCSI-2 device pass1: 3.300MB/s transfers da0 at mpt0 bus 0 target 0 lun 0 da0: <IBM-ESXS ST336607LC FN B25F> Fixed Direct Access SCSI-3 device da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 34715MB (71096640 512 byte sectors: 255H 63S/T 4425C) Mounting root from ufs:/dev/da0s1a stray irq 7 stray irq 7 stray irq 7
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?40BCDF01.1060600>