Date: Sat, 28 Sep 2002 11:54:15 -0400 From: Jim Brown <jpb@sixshooter.v6.thrupoint.net> To: freebsd-qa@freebsd.org Subject: Re: 4.7-RC2 Installation comments Message-ID: <20020928155415.GA74713@sixshooter.v6.thrupoint.net> In-Reply-To: <20020927154142.320d4051.rpratt1950@earthlink.net> References: <20020927154142.320d4051.rpratt1950@earthlink.net>
next in thread | previous in thread | raw e-mail | index | archive | help
* Randy Pratt <rpratt1950@earthlink.net> [2002-09-27 15:40]:
> I was unable to locate an md5 checksum for the 4.7-RC2.iso but it
> seemed to be okay.
>
> The install went smoothly as expected.
>
> Normally, I don't install KDE or Gnome but I tried the KDE desktop.
> When I reviewed the package selection menu, I noticed that it
> had only installed some of the kde libs and the kde base. The
> meta port for KDE was not marked as already having been installed.
> I selected the meta port and it installed the remaining uninstalled
> KDE elements (games, network, multimedia, etc).
>
> Is the intended behavior? I would have thought that the entire KDE
> suite would have been installed if I had selected it as my desktop
> during the install. I can repeat the install if needed, making notes
> of the packages that do get installed when selecting the KDE desktop
> as the default.
>
> I'll try a few more fresh installs in various ways, but things seem
> to be pretty smooth.
>
> Randy
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-qa" in the body of the message
IBM Thinkpad, dmesg output at end.
I installed from the RC2 iso this afternoon. Also a smooth install.
I did not select the desktop from the initial install, but rebooted.
After booting, I ran sysinstall and added the KDE desktop from the
configure submenu. I got the standard installation without any problems.
I did note that the ERRATA page still contains 4.6.2 info, but I
assume that is the last thing updated in the release cycle.
Congratulations again to the developers, release engineering and all
contributors on an outstanding job putting 4.7 together!
Best Regards,
jpb
===
bash-2.05b# dmesg
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RC2 #0: Thu Sep 26 04:07:11 GMT 2002
root@freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1132.38-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 267780096 (261504K bytes)
avail memory = 255377408 (249392K bytes)
Preloaded elf kernel "kernel" at 0xc050f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 14 entries at 0xc00fdeb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=3576)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <S3 model 8c2e graphics accelerator> at 0.0 irq 11
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 11 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f irq 11 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pcic0: <TI PCI-1420 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 11 at device 0.0 on pci2
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <TI PCI-1420 PCI-CardBus Bridge> mem 0x51000000-0x51000fff irq 11 at device 0.1 on pci2
pcic1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard1: <PC Card 16-bit bus (classic)> on pcic1
pci2: <unknown card> (vendor=0x11c1, dev=0x0449) at 2.0 irq 11
fxp0: <Intel Pro/100 Ethernet> port 0x6400-0x643f mem 0xc0200000-0xc0200fff irq 11 at device 8.0 on pci2
fxp0: Ethernet address 00:d0:59:aa:48:77
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 11
pci0: <unknown card> (vendor=0x8086, dev=0x2485) at 31.5 irq 11
orm0: <Option ROMs> at iomem 0xc0000-0xcdfff,0xce000-0xcefff,0xcf000-0xcffff,0xdc000-0xdffff,0xe0000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: cannot reserve I/O port range
ata1-slave: ATAPI identify retries exceeded
ad0: 28615MB <IC25N030ATCS04-0> [62016/15/63] at ata0-master UDMA100
acd0: CD-RW <UJDA720 DVD/CDRW> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
cd9660: RockRidge Extension
cd9660: RockRidge Extension
stray irq 7
stray irq 7
stray irq 7
cd9660: RockRidge Extension
stray irq 7
bash-2.05b#
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-qa" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020928155415.GA74713>