Date: Tue, 1 Jun 1999 12:03:05 +0100 (BST) From: lundman@argonaut.com Message-ID: <3753BF41.809ADE9@argonaut.com>
next in thread | raw e-mail | index | archive | help
Hello ISDNers :)
We are running NetBSD-1.4 (i386) here, and have just installed your ISDN
package .81 May '99. This is a long message, we appologise.
The ISDN card is asyscom isdnlink.
After patching the kernel and installed the ISDN package the kernel boot
up message was that of:
May 22 08:38:30 spoongate /netbsd: isapnp0: <ISDN CARD, ASU1690, , >
port 0x100/8 irq 3 not configured
But we spotted the kernel had support for asus 1688, so we modified
layer1/isapnp_isic.c to look for ASU1690 instead of ASU1688, and we got
further, however, it was expecting version 1.2 and slightly different
HSC0 and 1. Like:
May 27 10:06:06 spoongate /netbsd: isic0 at isapnp0 port 0x100/8 irq 3:
Dynalink IS64PH
May 27 10:06:06 spoongate /netbsd: isic0: HSCX VSTR test failed for
Dynalink PnP
May 27 10:06:06 spoongate /netbsd: isic0: HSC0: VSTR: 0x82
May 27 10:06:06 spoongate /netbsd: isic0: HSC1: VSTR: 0x82
May 27 10:06:06 spoongate /netbsd: isic0: ISAC 2085 Version V2.3 (B3)
(IOM-2)
May 27 10:06:06 spoongate /netbsd: isic0: HSCX 82525 Version A2
So to layer1/i4b_dynalink.c.c we went, and changed the compare for HSC0
and HSC1 to:
/* Read HSCX A/B VSTR. Expected value is 0x05 (V2.1). */
if( ((HSCX_READ(0, H_VSTR) & 0xf) != 0x2) || ((HSCX_READ(1,
H_VSTR) & 0xf) != 0x2) )
Rebooted once again, and finally we got:
Jun 1 02:39:18 spoongate /netbsd: isic0 at isapnp0 port 0x100/8 irq 3:
Dynalink IS64PH
Jun 1 02:39:18 spoongate /netbsd: isic0: ISAC 2085 Version V2.3 (B3)
(IOM-2)
Jun 1 02:39:18 spoongate /netbsd: isic0: HSCX 82525 Version A2
Jun 1 02:39:18 spoongate /netbsd: biomask 4040 netmask 4448 ttymask
444a
Jun 1 02:39:18 spoongate /netbsd: i4b: ISDN call control device
attached
Jun 1 02:39:18 spoongate /netbsd: i4btrc: 2 ISDN trace device(s)
attached
Jun 1 02:39:18 spoongate /netbsd: i4bctl: ISDN system control port
attached
Jun 1 02:39:18 spoongate /netbsd: i4brbch: 4 raw B channel access
device(s) attached
Jun 1 02:39:18 spoongate /netbsd: i4btel: 2 ISDN telephony interface
device(s) attached
Jun 1 02:39:18 spoongate /netbsd: i4bipr: 2 IP over raw HDLC ISDN
device(s) attached (VJ header compression)
Jun 1 02:39:18 spoongate /netbsd: i4bisppp: 2 ISDN SyncPPP device(s)
attached
Which we thought was encouraging :)
So, we created the PPP script like the handbook suggests, which executes
the following commands:
+ ifconfig isp0 delete -link1 down
+ spppcontrol isp0 myauthproto=pap
+ spppcontrol isp0 myauthname=uk,ppp,rbeswick
+ spppcontrol isp0 myauthsecret=craft-75trident
+ ifconfig isp0 0.0.0.0 XXX.XXX.XXX.XXX netmask 0xffffffff link1
^^^ remote ISPs gate IP
Then we go ifconfig isp0 up and try to telnet to XXX.XXX.XXX.XXX above.
We've started isdnd -d 1023 -F -l -L log
and the following is in the log file:
<OURPHONE> and <REMOTE> has the actualy phone numbers, not those strings
:) Tripple checked they are correct (what was called from Win95 etc)
01.06.1999 04:19:03 DBG init_controller_state: controller 0 is Dynalink
IS64PH
01.06.1999 04:19:03 DBG init_controller: found 1 ISDN controller(s)
01.06.1999 04:19:03 DBG entry 0: name = I4BPPP
01.06.1999 04:19:03 DBG entry 0: usrdevicename = isp
01.06.1999 04:19:03 DBG entry 0: usrdeviceunit = 0
01.06.1999 04:19:03 DBG entry 0: isdncontroller = 0
01.06.1999 04:19:03 DBG entry 0: isdnchannel = any
01.06.1999 04:19:03 DBG entry 0: local_phone_incoming = *
01.06.1999 04:19:03 DBG entry 0: remote_phone_incoming #0 = *
01.06.1999 04:19:03 DBG entry 0: local_phone_dialout = <OURPHONE>
01.06.1999 04:19:03 DBG entry 0: remote_phone_dialout #0 = <REMOTE>
01.06.1999 04:19:03 DBG entry 0: remdial_handling = first
01.06.1999 04:19:03 DBG entry 0: dialin_reaction = reject
01.06.1999 04:19:03 DBG entry 0: dialouttype = normal
01.06.1999 04:19:03 DBG entry 0: b1protocol = hdlc
01.06.1999 04:19:03 DBG entry 0: idle_time_in = 240
01.06.1999 04:19:03 DBG entry 0: idle_time_out = 60
01.06.1999 04:19:03 DBG entry 0: ratetype = 0
01.06.1999 04:19:03 DBG entry 0: unitlength = 90
01.06.1999 04:19:03 DBG entry 0: unitlengthsrc = rate
01.06.1999 04:19:03 DBG entry 0: dialretries = 3
01.06.1999 04:19:03 DBG entry 0: dialrandincr = 1
01.06.1999 04:19:03 DBG entry 0: recoverytime = 25
01.06.1999 04:19:03 DBG entry 0: usedown = 0
01.06.1999 04:19:03 DBG entry 0: downtries = 2
01.06.1999 04:19:03 DBG entry 0: downtime = 30
01.06.1999 04:19:03 DBG rates: NO entry for day 0 !!
(etc for all days)
01.06.1999 04:19:03 DBG ratesfile /etc/isdn/isdnd.rates read
successfully
01.06.1999 04:19:03 DMN i4b isdn daemon started (pid = 1335)
01.06.1999 04:19:04 DBG time < 1 - last 928235944:760066 now
928235944:760071
01.06.1999 04:19:05 DBG time OK! - last 928235944:760066 now
928235945:760025
01.06.1999 04:19:06 DBG time OK! - last 928235945:760188 now
928235946:760033
01.06.1999 04:19:07 DBG time OK! - last 928235946:760233 now
928235947:760027
01.06.1999 04:19:08 DBG time OK! - last 928235947:760200 now
928235948:760036
01.06.1999 04:19:09 DBG time OK! - last 928235948:760237 now
928235949:760028
01.06.1999 04:19:10 DBG time OK! - last 928235949:760214 now
928235950:760035
01.06.1999 04:19:11 DBG time OK! - last 928235950:760227 now
928235951:760035
(etc on the time lines, until I issued the telnet command and this
appears)
01.06.1999 04:19:28 DBG msg_dialout: dial req from isp, unit 0
01.06.1999 04:19:28 DBG setup_dialout: entry I4BPPP ok!
01.06.1999 04:19:28 DBG find_by_device_for_dialout: found entry 0!
01.06.1999 04:19:28 DBG FSM event [msg-dialout]: [idle => dialing]
01.06.1999 04:19:28 DBG F_DIAL: local dial out request
01.06.1999 04:19:28 DBG select_first_dialno: only one no, no =
08450798555
01.06.1999 04:19:28 CHD 00006 I4BPPP rate 60 sec/unit (ratescan fail)
01.06.1999 04:19:28 DBG sendm_connect_req: ctrl = 0, chan = -1
01.06.1999 04:19:28 DBG decr_free_channels: ctrl 0, now 1 chan free
01.06.1999 04:19:28 CHD 00006 I4BPPP dialing out from 01392444369 to
08450798555
01.06.1999 04:19:28 DBG time < 900000us - last 928235967:760231 now
928235968:43
7709
01.06.1999 04:19:29 DBG time OK! - last 928235967:760231 now
928235969:430035
Meanwhile, in the syslog, the following errors occur:
Jun 1 04:19:30 spoongate /netbsd: i4b-L2-i4b_T202_timeout: unit 0, N202
= 3
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-ph_data_req: No Space in TX
FIFO, state = F4 Awaiting Signal
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-timer3_expired: state = F4
Awaiting Signal
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: HSCX B: ISTA =
0x0
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: ISAC: ISTA =
0xff
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: ISAC: EXIR =
0xff
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: ISAC: CISQ =
0xff
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: ISAC: SQRR =
0xff
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: HSCX B: IMASK =
0xff
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: HSCX A: IMASK =
0xf8
Jun 1 04:19:30 spoongate /netbsd: i4b-L1-isic_recover: ISAC: IMASK =
0x2a
Jun 1 04:19:32 spoongate /netbsd: i4b-L3-T303_timeout: SETUP not
answered, cr = 121
Jun 1 04:19:32 spoongate /netbsd: i4b-L3-next_l3state: FSM illegal
state, state = ST_OW - Out Wait EST, event = EV_T303EXP - T303 timeout!
and we are stuck :(
Can any help or give a hint at which direction we should go?
Anything would be appreciated!
Lund
--
Jorgen Lundman <lundman@argonaut.com>
Programmer & Unix Administrator
http://www.whiterose.net/users/lundman/
"It is easy to be wise in hindsight"
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-isdn" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3753BF41.809ADE9>