Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 22 May 2013 19:34:05 +0530
From:      hrkesh sahu <hrisikeshsahu@gmail.com>
To:        =?ISO-8859-1?Q?Trond_Endrest=F8l?= <Trond.Endrestol@fagskolen.gjovik.no>
Cc:        FreeBSD questions <freebsd-questions@freebsd.org>
Subject:   Re: Fresh installation 9.1
Message-ID:  <CAMB42mww6yFFTip9isMxUirH92Yh+V_RS4QMJgi3qwcMh20g1A@mail.gmail.com>
In-Reply-To: <alpine.BSF.2.00.1305221505550.72982@mail.fig.ol.no>
References:  <CAMB42mzLT_T7UEsCASZg6AvQ67=6QwVqrtWy_roWPohK4jO1bw@mail.gmail.com> <CAMB42myZvcABC0p167RtDMxF=Qv0rXxpYi_B9EiVz9HQe-niDg@mail.gmail.com> <alpine.BSF.2.00.1305091019190.72982@mail.fig.ol.no> <CAMB42mzFdMrDqFbRXW5rj8NyK2rwmTKP4C_UOiMirq7YpAMc0A@mail.gmail.com> <alpine.BSF.2.00.1305220825560.72982@mail.fig.ol.no> <CAMB42mwjMoOsjdDVUyo8dazym63atBfySFt4E38Kbd2vq0e9Gw@mail.gmail.com> <alpine.BSF.2.00.1305220925560.72982@mail.fig.ol.no> <CAMB42mws6LXAWSnwT56Hjf91qrCLJhFbB+=SZRMebfG5v_3zCA@mail.gmail.com> <alpine.BSF.2.00.1305221505550.72982@mail.fig.ol.no>

Next in thread | Previous in thread | Raw E-Mail | Index | Archive | Help
Hi Trond,
Thanks a lot for a clear reply.
Could you please tell me Laptop1 ipv6 configuration details?
as laptop auto configuration will generate the LL address for a auto ipv6
configuration.
For Interface rl0 ipv6 address
ifconfig_rl0_ipv6=3D"inet6 fd8f:d6d0:e6e7:100::101 prefixlen 64" ,

what will be laptop ipv6 address?

Regards




On Wed, May 22, 2013 at 6:54 PM, Trond Endrest=F8l <
Trond.Endrestol@fagskolen.gjovik.no> wrote:

> On Wed, 22 May 2013 18:21+0530, hrkesh sahu wrote:
>
> > Hi Trond ,
> > Thanks a lot.
> > Now i am able to ping to other network with IPv4 address.
> >
> > For IPv6 I added these lines in rc.conf -
> > first I included -
> > ipv6_gateway_enable=3D"YES"
> >
> > ++> Laptop1( Ipv6 address fe80::224:7eff:fee0:6b51) is connected to
> > interface rl0 ( ipv6 address - fe80::21f:b5ff:fe48:9f73)
> > While doing ping6 from "fe80::224:7eff:fee0:6b51" to
> > "fe80::21f:b5ff:fe48:9f73" - it is working. Neighbor advertisement from
> > "fe80::21f:b5ff:fe48:9f73" is happening.
> > while doing from ping6 from "fe80::224:7eff:fee0:6b51" to other interfa=
ce
> > "fe80::21f:d0ff:fe40:8bbd" , then there is no Neighbor advertisement.
> >
> > After this I included these two lines to rc.conf -
> >
> > rtadvd_enable=3D"YES"
> > rtadvd_interfaces=3D"rl0"
> >
> > I have not created any file like /etc/rtadvd.conf . Do i need to create
> > this configuration file?
> > if yes, what should be the input to rtadvd.conf for  link local address=
?
> >
> > please find Ipv6 interface details.
> >
> >
> > Ifconfig
> > --------------------
> > re0: flags=3D8843<UP,Broadcast,
> > Running,Simplex,Multicast> Metric 0 mtu 1500
> > options=3D8209b<RXCSUM,TXCSUM,
> > VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
> > ether 00:1f:d0:40:8b:bd
> > inet6 fe80::21f:d0ff:fe40:8bbd%re0 prefixlen 64 scopeid 0x5
> > inet 192.168.200.101 netmask 0xffffff00         broadcast 192.168.200.2=
55
> > nd6 options=3D21<PERFORMNUD,AUTO_
> > LINKLOCAL>
> > media:Enthernet autoselect (none)
> > status:active
> >
> > rl0: flags=3D8843<UP,Broadcast,
> > Running,Simplex,Multicast> Metric 0 mtu 1500
> > options=3D2008<VLAN_MTU,WOL_MAGIC>
> > ether 00:10:b5:48:9f:73
> > inet6 fe80::21f:b5ff:fe48:9f73%rl0 prefixlen 64 scopeid 0xa
> > inet 192.168.100.101 netmask 0xffffff00         broadcast 192.168.100.2=
55
> > nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
> > media:Enthernet autoselect (none)
> > status: active
>
> Congratz on achieving active carrier wave on your NICs.
>
> Right now your system is running with link-local IPv6 addresses. You
> may view LL addresses as VLAN local. Packets to such addresses will
> never ever be forwarded by a router.
>
> Instead set up either official IPv6 addresses/subnets or create your
> own Unique Local Addresses (ULA) as I wrote previously about.
>
> Augment your /etc/rc.conf file with, say:
>
> ifconfig_rl0_ipv6=3D"inet6 fd8f:d6d0:e6e7:100::101 prefixlen 64"
>
> You may assign the IPv6 address manually to avoid restarting the
> networking subsystem or the whole machine:
>
> ifconfig rl0 inet6 fd8f:d6d0:e6e7:100::101 prefixlen 64
>
> Next, create /etc/rtadvd.conf with the following contents:
>
> rl0:\
>         :addr=3D"fd8f:d6d0:e6e7:100::":prefixlen#64:
>
> If you want IPv6 routing on the re0 interface, you need, say this, in
> /etc/rc.conf:
>
> ifconfig_re0_ipv6=3D"inet6 fd44:13de:a366:200::1 prefixlen 64"
>
> Assign the IPv6 address manually using:
>
> ifconfig re0 inet6 fd44:13de:a366:200::1 prefixlen 64
>
> And add this to /etc/rtadvd.conf:
>
> re0:\
>         :addr=3D"fd44:13de:a366:200::":prefixlen#64:
>
> You'll need to restart rtadvd by issuing /etc/rc.d/rtadvd restart.
>
> Happy hacking.
>
> > Regards
> > Hrisikesh
> >
> > On Wed, May 22, 2013 at 1:03 PM, Trond Endrest=F8l <
> > Trond.Endrestol@fagskolen.gjovik.no> wrote:
> >
> > > On Wed, 22 May 2013 12:38+0530, hrkesh sahu wrote:
> > >
> > > > Hi ,
> > > > Thanks a lot for this quick reply.
> > > > Sorry i missed the " in the end while typing. It's a typo.
> > > > I provided the ouput of " nestat -r " and "ifconfig".
> > > >
> > > > > netstat -r
> > > > --------------
> > > > routing tables  -
> > > >
> > > > internet :
> > > > -----------
> > > > destination                   Gateway
> > > > Flags                       Refs
> > > > Use                               Netif Expire
> > > > default                         192.168.200.1
> > > > UGS                       0
> > > > 0                                  re0
> > > > localhost                      link#12
> > > > UH                         0
> > > > 148                               lo0
> > > > 192.168.100.0              link#10
> > > > U                           0
> > > > 0                                   rl0
> > > > 192.168.100.101           link#10                      UHS
> > > >                      0
> > > > 0                                   lo0
> > > > 192.168.200.0              link#5
> > > > U                           0
> > > > 0                                   re0
> > > > 192.168.200.101           link#5                      UHS
> > > >                        0
> > > > 0                                   lo0
> > > >
> > > > Internet6:
> > > > -------------------
> > > > Ipv6 details
> > > >
> > > > > Ifconfig
> > > > --------------------
> > > > re0: flags=3D8843<UP,Broadcast,Running,Simplex,Multicast> Metric 0 =
mtu
> 1500
> > > >
> > >
> options=3D8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAG=
IC,LINKSTATE>
> > > > ether 00:1f:d0:40:8b:bd
> > > > inet6 fe80::21f:d0ff:fe40:8bbd%re0 prefixlen 64 scopeid 0x5
> > > > inet 192.168.200.101 netmask 0xffffff00         broadcast
> 192.168.200.255
> > > > nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
> > > > media:Enthernet autoselect (none)
> > > > status: no carrier
> > > >
> > > > rl0: flags=3D8843<UP,Broadcast,Running,Simplex,Multicast> Metric 0 =
mtu
> 1500
> > > > options=3D2008<VLAN_MTU,WOL_MAGIC>
> > > > ether 00:10:b5:48:9f:73
> > > > inet6 fe80::21f:b5ff:fe48:9f73%rl0 prefixlen 64 scopeid 0xa
> > > > inet 192.168.100.101 netmask 0xffffff00         broadcast
> 192.168.100.255
> > > > nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
> > > > media:Enthernet autoselect (none)
> > > > status: no carrier
> > > >
> > > > there is a plip0 and lo0.
> > >
> > > Neither NIC is connected to any equipment, e.g. switch, hub, or
> > > computer (status: no carrier). Make sure you can use a straight
> > > network cable, else you'll need to get a couple of cross wired networ=
k
> > > cables and use those instead.
> > >
> > > Next, confirm the sysctl net.inet.ip.forwarding is set to 1 by
> > > running the sysctl net.inet.ip.forwarding command.
> > >
> > > If not, you can set the sysctl to 1 by running the sysctl
> > > net.inet.ip.forwarding=3D1 command, and you probably should inspect t=
he
> > > /etc/rc.conf file one more time.
> > >
> > > Once you connect the computer to the two networks, the IPv4 routing
> > > should work. If not, come back.
> > >
> > > > Regards
> > > > Hrisikesh
> > > >
> > > > On Wed, May 22, 2013 at 12:02 PM, Trond Endrest=F8l <
> > > > Trond.Endrestol@fagskolen.gjovik.no> wrote:
> > > >
> > > > > On Wed, 22 May 2013 11:10+0530, hrkesh sahu wrote:
> > > > >
> > > > > > Hi All,
> > > > > > IPv4 Routing  -
> > > > > > ------------------------
> > > > > > I disabled the DHCP from rc.conf for both the interface. but
> still I
> > > am
> > > > > not
> > > > > > able to route trafic from one interface to another.
> > > > > >
> > > > > > rc.conf
> > > > > > ---------------
> > > > > > hostname=3D"idc-freebsd"
> > > > > > keymap=3D"hy.armscii-8.kbd"
> > > > > > #ifconfig_re0=3D"DHCP"
> > > > > > #ifconfig_rl0=3D"DHCP"
> > > > > > dumpdev=3D"NO"
> > > > >
> > > > > > ifconfig_rl0=3D"inet 192.168.100.101 netmask 255.255.255.0
> > > > > > ifconfig_re0=3D"inet 192.168.200.101 netmask 255.255.255.0
> > > > >
> > > > > Are the two lines above copied straight from your rc.conf file?
> > > > > If so, both lines are missing a " at the end. Please check to see
> if
> > > > > this is needed.
> > > > >
> > > > > Next, the outputs of the ifconfig command and the netstat -r
> command
> > > > > should reveal something interesting. Would you please post the
> > > > > results from these two commands?
> > > > >
> > > > > > ipv6_activate_all_interfaces=3D"YES"
> > > > > > gateway_enable=3D"YES"
> > > > > > default_router=3D"192.168.200.1"
> > > > > >
> > > > > > I am using FreeBSD - 9.1 Release version
> > > > > >
> > > > > > I need to communicate between two different subnets.
> > > > > >
> > > > > > Am i missing anything to enable freebsd as router?
> > > > > > Do i need to add a route entry?
> > > > > >
> > > > > > If possible could you please share rc.conf file with IPv4
> routing?
> > > > > >
> > > > > > Regards
> > > > > > Hrisikesh
> > > > > >
> > > > > > On Thu, May 9, 2013 at 2:04 PM, Trond Endrest=F8l <
> > > > > > Trond.Endrestol@fagskolen.gjovik.no> wrote:
> > > > > >
> > > > > > > On Thu, 9 May 2013 12:18+0530, hrkesh sahu wrote:
> > > > > > >
> > > > > > > > > HI All,
> > > > > > > > >
> > > > > > > > I have a FreeBSD 9.1 Release installed with TWO NIC cards. =
I
> was
> > > > > trying
> > > > > > > to
> > > > > > > > make this FreeBSD machine as a router .
> > > > > > > > This is my rc.conf
> > > > > > > > --------------------------------
> > > > > > > > ifconfig_rl0 =3D "inet 192.168.100.101 netmask 255.255.255.=
0"
> > > > > > > > ifconfig_re0=3D"inet 192.168.200.101 netmask 255.255.255.0"
> > > > > > > >
> > > > > > > > gateway_enable =3D "YES"
> > > > > > > > ifconfig_rl0 =3D "DHCP"
> > > > > > > > ifconfig_re0 =3D "DHCP"
> > > > > > > >
> > > > > > > > defaultrouter =3D "192.168.100.1"
> > > > > > > > ipv6_activate_all_interfaces =3D "YES"
> > > > > > > > sshd_enable =3D "YES"
> > > > > > > > synchronous_dhclient=3D"YES"
> > > > > > > >
> > > > > > > > Please help me to establish a IPv4 router.
> > > > > > > > Both the interfaces are connected to to different laptops
> with a
> > > > > static
> > > > > > > IP
> > > > > > > > address.
> > > > > > >
> > > > > > > You should place a # in front of the two lines:
> > > > > > >
> > > > > > > > ifconfig_rl0 =3D "DHCP"
> > > > > > > > ifconfig_re0 =3D "DHCP"
> > > > > > >
> > > > > > > Next, you probably shouldn't place spaces before and after th=
e
> > > equal
> > > > > > > signs.
> > > > > > >
> > > > > > > > Laptop 1 =3D 192.168.100.102  ( connected to interface rl0)
> > > gateway  -
> > > > > > > > 192.168.100.1
> > > > > > > >
> > > > > > > > Laptop 2 =3D 192.168.200.102 ( connected to interface re0)
> > > > > > > > ping from Laptop1 -> rl0 is successful
> > > > > > > > but ping from Laptop1 -> re0 is not successful.
> > > > > > > >
> > > > > > > > After this I want to know also How to make this as IPv6
> router?
> > > > > > >
> > > > > > > See
> > > > > > >
> > > > >
> > >
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/network-ipv6.ht=
ml
> > > > > > > .
> > > > > > >
> > > > > > > You probably should create a ULA prefix or two, and assign
> these to
> > > > > > > your router interfaces. http://www.sixxs.net/tools/grh/ula/mi=
ght
> > > help
> > > > > > > you.
> > > > > > >
> > > > > > > Something along these lines might help you achieve what you
> want:
> > > > > > >
> > > > > > > ifconfig_rl0_ipv6=3D"inet6 fd8f:d6d0:e6e7:100::1 prefixlen 64=
"
> > > > > > > ifconfig_re0_ipv6=3D"inet6 fd44:13de:a366:200::1 prefixlen 64=
"
> > > > > > > ipv6_gateway_enable=3D"YES"
> > > > > > >
> > > > > > > Finally you probably should configure and enable Router
> > > Advertisement
> > > > > > > and Host Auto Configuration as explained in section 32.11.6 o=
f
> > > > > > >
> > > > >
> > >
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/network-ipv6.ht=
ml
> > > > > > > .
>
> --
> +-------------------------------+------------------------------------+
> | Vennlig hilsen,               | Best regards,                      |
> | Trond Endrest=F8l,              | Trond Endrest=F8l,                   =
|
> | IT-ansvarlig,                 | System administrator,              |
> | Fagskolen Innlandet,          | Gj=F8vik Technical College, Norway,  |
> | tlf. mob.   952 62 567,       | Cellular...: +47 952 62 567,       |
> | sentralbord 61 14 54 00.      | Switchboard: +47 61 14 54 00.      |
> +-------------------------------+------------------------------------+
>



Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?CAMB42mww6yFFTip9isMxUirH92Yh+V_RS4QMJgi3qwcMh20g1A>