Date: Sun, 27 Jan 2008 19:30:02 GMT From: Kenneth <kennethcf@earthlink.net> To: freebsd-usb@FreeBSD.org Subject: Re: kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G memory, works with 512 M Message-ID: <200801271930.m0RJU2UD033432@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR usb/120034; it has been noted by GNATS. From: Kenneth <kennethcf@earthlink.net> To: Remko Lodder <remko@FreeBSD.org> Cc: freebsd-gnats-submit@FreeBSD.org Subject: Re: kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G memory, works with 512 M Date: Sun, 27 Jan 2008 14:12:20 -0500 (GMT-05:00) ------------OIMQJV4d8WPYIxnea41D38 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 7bit OK..more info. Seems like disabling USB when 1.5G is plugged in works, but then I loose my working USB which I use for my working memory stick and floppy drive. Enabling and disableing ACPI had no effect. When I enable usb, dmesg is the same up to the point of hanging with the exception of the mem and iomem fields in the "atapci0" and "atapci1" lines. With 1.5G and usb enabled, my hung kernel says: atapci0: ...mem 0x80207600 - 0x802077ff... the port locations are the same atapci1: ...mem 0x80207400 - 0x802075ff... the port locations are the same Attached are full dmesg outputs of configurations that work, i.e. no hang: "dmesg_0.5G" - 0.5G memory, full usb, full ACPI (6.3 .iso kernel) "dmesg_1.0G" - 1.0G memory, full usb, full ACPI (6.3 .iso kernel) "dmesg_1.5G_nousb" - 1.5G memory, no usb, full ACPI (6.3 .iso kernel) I also tried 6.2 .iso kernel from the install CD and it still hangs with 1.5G. I do not know how I can provide you with a full dmesg when the system hangs. Can you tell me how I can log output of a boot sequence that hangs for later analysis? I have no shells in which to run dmesg. Extended logging does not help as I still do not know how to log it. -----Original Message----- >From: Remko Lodder <remko@FreeBSD.org> >Sent: Jan 27, 2008 5:44 AM >To: Kenneth Freidank <kennethcf@earthlink.net> >Cc: freebsd-gnats-submit@FreeBSD.org >Subject: Re: kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G memory, works with 512 M > >Kenneth Freidank wrote: > >Could you disable USB support in the bios and see where that leads >up to? could it be that the additional memory kicks in the USB >controller? and/or perhaps any other region? > >You did not provide a full boot dmesg btw; just giving parts of >it makes it very hard to see what might be going on, in addition >it could be interesting to start the freebsd installation without >acpi support, and doing a boot verbose (that's 2 additional things >we might like to see). > >Thanks, >remko > >-- >/"\ Best regards, | remko@FreeBSD.org >\ / Remko Lodder | remko@EFnet > X http://www.evilcoder.org/ | >/ \ ASCII Ribbon Campaign | Against HTML Mail and News ------------OIMQJV4d8WPYIxnea41D38 Content-Disposition: attachment; filename="dmesg_0.5G" Content-Type: application/octet-stream; name=dmesg_0.5G Content-Transfer-Encoding: 7bit Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008 root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.12-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf4a Stepping = 10 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR> AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF> Logical CPUs per core: 2 real memory = 468365312 (446 MB) avail memory = 444076032 (423 MB) ACPI APIC Table: <INTEL D11020M > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 4 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12) acpi0: <INTEL D11020M> on motherboard acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21 acpi0: Power Button (fixed) unknown: I/O range not supported Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_throttle0: <ACPI CPU Throttling> on cpu0 cpu1: <ACPI CPU> on acpi0 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 5.0 (no driver attached) atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x30207600-0x302077ff irq 23 at device 17.0 on pci0 ata2: <ATA channel 0> on atapci0 ata3: <ATA channel 1> on atapci0 atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x30207400-0x302075ff irq 22 at device 18.0 on pci0 ata4: <ATA channel 0> on atapci1 ata5: <ATA channel 1> on atapci1 ohci0: <ATI SB400 USB Controller> irq 19 at device 19.0 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: <ATI SB400 USB Controller> on ohci0 usb0: USB revision 1.0 uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered ohci1: <ATI SB400 USB Controller> irq 19 at device 19.1 on pci0 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0, legacy support usb1: <ATI SB400 USB Controller> on ohci1 usb1: USB revision 1.0 uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 4 ports with 4 removable, self powered ehci0: <ATI SB400 USB 2.0 controller> irq 19 at device 19.2 on pci0 ehci0: [GIANT-LOCKED] usb2: waiting for BIOS to give up control usb2: timed out waiting for BIOS usb2: EHCI version 1.0 usb2: companion controllers, 4 ports each: usb0 usb1 usb2: <ATI SB400 USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 8 ports with 8 removable, self powered pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci2 ata1: <ATA channel 1> on atapci2 pci0: <multimedia> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci2: <ACPI PCI bus> on pcib2 rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x30010000-0x300100ff irq 21 at device 2.0 on pci2 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:19:d1:16:5f:fb pci2: <simple comms> at device 4.0 (no driver attached) atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 umass0: vendor 0x058f USB Reader, rev 1.10/1.00, addr 2 Timecounters tick every 1.000 msec hptrr: no controller detected. ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133 ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100 acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33 SMP: AP CPU #1 Launched! da0 at umass-sim0 bus 0 target 0 lun 0 da0: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device da0: 1.000MB/s transfers da0: Attempt to query device size failed: NOT READY, Medium not present da1 at umass-sim0 bus 0 target 0 lun 1 da1: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device da1: 1.000MB/s transfers da1: Attempt to query device size failed: NOT READY, Medium not present da2 at umass-sim0 bus 0 target 0 lun 2 da2: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device da2: 1.000MB/s transfers da2: Attempt to query device size failed: NOT READY, Medium not present da3 at umass-sim0 bus 0 target 0 lun 3 da3: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device da3: 1.000MB/s transfers da3: Attempt to query device size failed: NOT READY, Medium not present Trying to mount root from ufs:/dev/ad1s2a ------------OIMQJV4d8WPYIxnea41D38 Content-Disposition: attachment; filename="dmesg_1.0G" Content-Type: application/octet-stream; name=dmesg_1.0G Content-Transfer-Encoding: 7bit Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008 root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.13-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf4a Stepping = 10 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR> AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF> Logical CPUs per core: 2 real memory = 938127360 (894 MB) avail memory = 904040448 (862 MB) ACPI APIC Table: <INTEL D11020M > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 4 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12) acpi0: <INTEL D11020M> on motherboard acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21 acpi0: Power Button (fixed) unknown: I/O range not supported Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_throttle0: <ACPI CPU Throttling> on cpu0 cpu1: <ACPI CPU> on acpi0 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 5.0 (no driver attached) atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x60207600-0x602077ff irq 23 at device 17.0 on pci0 ata2: <ATA channel 0> on atapci0 ata3: <ATA channel 1> on atapci0 atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x60207400-0x602075ff irq 22 at device 18.0 on pci0 ata4: <ATA channel 0> on atapci1 ata5: <ATA channel 1> on atapci1 ohci0: <ATI SB400 USB Controller> irq 19 at device 19.0 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: <ATI SB400 USB Controller> on ohci0 usb0: USB revision 1.0 uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered ohci1: <ATI SB400 USB Controller> irq 19 at device 19.1 on pci0 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0, legacy support usb1: <ATI SB400 USB Controller> on ohci1 usb1: USB revision 1.0 uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 4 ports with 4 removable, self powered ehci0: <ATI SB400 USB 2.0 controller> irq 19 at device 19.2 on pci0 ehci0: [GIANT-LOCKED] usb2: waiting for BIOS to give up control usb2: timed out waiting for BIOS usb2: EHCI version 1.0 usb2: companion controllers, 4 ports each: usb0 usb1 usb2: <ATI SB400 USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 8 ports with 8 removable, self powered pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci2 ata1: <ATA channel 1> on atapci2 pci0: <multimedia> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci2: <ACPI PCI bus> on pcib2 rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x60010000-0x600100ff irq 21 at device 2.0 on pci2 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:19:d1:16:5f:fb pci2: <simple comms> at device 4.0 (no driver attached) atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 umass0: vendor 0x058f USB Reader, rev 1.10/1.00, addr 2 Timecounters tick every 1.000 msec hptrr: no controller detected. ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133 ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100 acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33 SMP: AP CPU #1 Launched! da0 at umass-sim0 bus 0 target 0 lun 0 da0: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device da0: 1.000MB/s transfers da0: Attempt to query device size failed: NOT READY, Medium not present da1 at umass-sim0 bus 0 target 0 lun 1 da1: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device da1: 1.000MB/s transfers da1: Attempt to query device size failed: NOT READY, Medium not present da2 at umass-sim0 bus 0 target 0 lun 2 da2: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device da2: 1.000MB/s transfers da2: Attempt to query device size failed: NOT READY, Medium not present da3 at umass-sim0 bus 0 target 0 lun 3 da3: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device da3: 1.000MB/s transfers da3: Attempt to query device size failed: NOT READY, Medium not present Trying to mount root from ufs:/dev/ad1s2a ------------OIMQJV4d8WPYIxnea41D38 Content-Disposition: attachment; filename="dmesg_1.5G_nousb" Content-Type: application/octet-stream; name=dmesg_1.5G_nousb Content-Transfer-Encoding: 7bit Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008 root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.13-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf4a Stepping = 10 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR> AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF> Logical CPUs per core: 2 real memory = 1474998272 (1406 MB) avail memory = 1431105536 (1364 MB) ACPI APIC Table: <INTEL D11020M > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 4 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12) acpi0: <INTEL D11020M> on motherboard acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21 acpi0: Power Button (fixed) unknown: I/O range not supported Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_throttle0: <ACPI CPU Throttling> on cpu0 cpu1: <ACPI CPU> on acpi0 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_perf1: <ACPI CPU Frequency Control> on cpu1 acpi_perf1: failed in PERF_STATUS attach device_attach: acpi_perf1 attach returned 6 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 5.0 (no driver attached) atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x80204600-0x802047ff irq 23 at device 17.0 on pci0 ata2: <ATA channel 0> on atapci0 ata3: <ATA channel 1> on atapci0 atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x80204400-0x802045ff irq 22 at device 18.0 on pci0 ata4: <ATA channel 0> on atapci1 ata5: <ATA channel 1> on atapci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci2 ata1: <ATA channel 1> on atapci2 pci0: <multimedia> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci2: <ACPI PCI bus> on pcib2 rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x80010000-0x800100ff irq 21 at device 2.0 on pci2 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:19:d1:16:5f:fb pci2: <simple comms> at device 4.0 (no driver attached) atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec hptrr: no controller detected. ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133 ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100 acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33 SMP: AP CPU #1 Launched! Trying to mount root from ufs:/dev/ad1s2a ------------OIMQJV4d8WPYIxnea41D38--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200801271930.m0RJU2UD033432>