Date: Mon, 18 Jun 2001 12:55:30 -0700 (PDT) From: shailesh sheoran <shailesh@ece.ubc.ca> Cc: FreeBSD-Questions <freebsd-questions@freebsd.org> Subject: d-link 530TX + cards still dysfunctional Message-ID: <Pine.GSO.4.33.0106181239520.12268-100000@shannon.ece.ubc.ca> In-Reply-To: <032401c0f5d4$dd015da0$3200000a@Intranet>
next in thread | previous in thread | raw e-mail | index | archive | help
hi,
i am trying to setup 2 dlink dfe530tx+ cards on my PIII
750MHz freebsd 4.3 Release system.
despite all efforts I still can't get them working. i have tried
looking for information everywhere but
the standard procedure of adding the lines
device miibus
device rl
isn't working for me. I know the card is not damaged because i can access
internet from windows98 but Freebsd still can't get the card working.
i am sure it should use the realtek 8139 driver because that's the
driver that came with the card too. (but there is no FreeBSD version of it
on the floppy, only linux and windows)
Following is the output i get from dmesg:
-------------------------------------------------------------------------
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-RELEASE #13: Mon Jun 18 12:34:08 PDT 2001
root@:/usr/src/sys/compile/MKERNEL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (757.46-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 134131712 (130988K bytes)
config> di sn0
config> di lnc0
config> di ie0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 126275584 (123316K bytes)
APreloaded elf kernel "kernel" at 0xc043c000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc043c09c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=1131)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <NVidia model 0110 graphics accelerator> at 0.0 irq 11
pcib2: <PCI to PCI bridge (vendor=8086 device=244e)> at device 30.0 on
pci0
pci2: <PCI bus> on pcib2
pcm0: <AudioPCI ES1371> port 0xd800-0xd83f irq 9 at device 11.0 on pci2
**************************DLINK DFE 530TX+ CARDS**********************
pci2: <unknown card> (vendor=0x1186, dev=0x1300) at 12.0 irq 9
pci2: <unknown card> (vendor=0x1186, dev=0x1300) at 13.0 irq 9
**********************************************************************
isab0: <PCI to ISA bridge (vendor=8086 device=2440)> at device 31.0 on
pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0xb800-0xb80f at device 31.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <UHCI (generic) USB controller> port 0xb400-0xb41f irq 5 at device
31.2 on pci0
uhci0: (New UHCI DeviceId=0x24428086)
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: (0x24428086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10
uhci1: <UHCI (generic) USB controller> port 0xb000-0xb01f irq 9 at device
31.4 on pci0
uhci1: (New UHCI DeviceId=0x24448086)
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: (0x24448086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 19546MB <FUJITSU MPG3204AT E> [39714/16/63] at ata0-master UDMA100
acd0: DVD-ROM <DVDROM 10X> at ata1-slave using PIO4
Mounting root from ufs:/dev/ad0s2a
WARNING: / was not properly dismounted
------------------------------------------------------------------------
I have a few points of confusion also. Hopefully someone could
enlighten me.
1. In file /usr/src/sys/i386/conf/LINT , it says "include files
'device miibus0' in kernel configuration for mii devices to
work"
Is that same as the line "device miibus" in GENERIC/MKERNEL ?
2. Do i need to tamper with BIOS PNP settings?
3. Do i need to add something to the /boot/kernel.conf file?
Could someone please please help me out.
Thanks,
Shailesh Sheoran
M.ASc.
Department of Electrical Engineering
University of British Columbia
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.33.0106181239520.12268-100000>