Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 5 Jul 2018 10:20:29 -0700 (PDT)
From:      "Rodney W. Grimes" <freebsd-rwg@pdx.rh.CN85.dnsmgr.net>
To:        Linus Sundqvist <linus.sundqvist@loopia.se>
Cc:        Toomas Soome <tsoome@me.com>, freebsd-current@freebsd.org, imp@freebsd.org
Subject:   Re: Unable to UEFI boot 11.2 ISO (latest 12.0 as well)
Message-ID:  <201807051720.w65HKTe4048658@pdx.rh.CN85.dnsmgr.net>
In-Reply-To: <aa47a1d4-64bb-5c57-8be7-203533eb6d16@loopia.se>

next in thread | previous in thread | raw e-mail | index | archive | help
> Here's the output, variable 'currdev' not found:
> https://imgur.com/LlBygfr

Hum, currdev didnt get set, but I see the loaddevice looks to be
cd1:  Toomas is right, we have an edge case here that is failing
to set currdev properly.

> 
> And to answer Rodneys question from before, this is the emulated CD drive from a Dell iDRAC (remote console thingy).

Thanks, that helps.  I'll try to duplicate this failure mode since I have Dells,
IIRC this virtual emulated CD drive shows up as a USB device.

> Med v?nlig h?lsning/Best Regards
> Linus Sundqvist
> System Engineer, Loopia AB
> 
> On 05/07/18 09:17, Toomas Soome wrote:
> > Could you check, show currdev from OK prompt before setting it.
> > 
> > Somehow the boot device path is shown but we fail to recognize it (as seen by error message). However, the lsdev -v does show the path, so the efipart.c seems to do its work correctly. I feel, there should be some corner case in efi/loader/main.c where we detect the boot device.
> > 
> > Rgds,
> > Toomas
> > 
> > Sent from my iPhone
> > 
> >> On 5 Jul 2018, at 09:32, Linus Sundqvist <linus.sundqvist@loopia.se> wrote:
> >>
> >> Running these commands makes the boot menu show up, and then takes me to the BSD installer!

Good, so there is a work around....


> >> Med v?nlig h?lsning/Best Regards
> >> Linus Sundqvist
> >> System Engineer, Loopia AB
> >>
> >>> On 04/07/18 16:50, Toomas Soome wrote:
> >>> set currdev=cd1:
> >>> include /boot/loader.rc
> >>>
> >>> This should give menu/boot.
> >>>
> >>> Rgds,
> >>> Toomas
> >>>
> >>> Sent from my iPhone
> >>>
> >>>> On 4 Jul 2018, at 16:25, Linus Sundqvist <linus.sundqvist@loopia.se> wrote:
> >>>>
> >>>> Hi,
> >>>>
> >>>> Sure, while using the 12.0 ISO here is lsdev -v and ls cd0:
> >>>> https://imgur.com/RmYpg7u
> >>>>
> >>>> and here is ls cd1:
> >>>> https://imgur.com/FPsixOw
> >>>>
> >>>> Med v?nlig h?lsning/Best Regards
> >>>> Linus Sundqvist
> >>>> System Engineer, Loopia AB
> >>>>
> >>>>> On 04/07/18 15:08, Toomas Soome wrote:
> >>>>> Can you post lsdev -v output?
> >>>>>
> >>>>> Also, could you try ls command? Like, ls cd0:   
> >>>>>
> >>>>> Rgds,
> >>>>> Toomas
> >>>>>
> >>>>> Sent from my iPhone
> >>>>>
> >>>>>> On 4 Jul 2018, at 12:28, Linus Sundqvist <linus.sundqvist@loopia.se> wrote:
> >>>>>>
> >>>>>> Hi,
> >>>>>>
> >>>>>> I'm unable to boot up the amd64 11.2 disk1 ISO as well as the latest amd64 12.0 disk1 ISO (20180628) using UEFI on a Dell PowerEdge R430 by getting this error:
> >>>>>> https://imgur.com/a/Idljfhm
> >>>>>>
> >>>>>> The bootonly ISOs seems to show the same error message.
> >>>>>>
> >>>>>> Changing the server to boot via BIOS loads the setup correctly, however, I want to use UEFI on all our servers, which I have done before.
> >>>>>>
> >>>>>> The 11.1 ISO boots without any trouble at all using both UEFI and BIOS.
> >>>>>>
> >>>>>> I was helped by koobs in #freebsd @ Freenode who asked me to send an e-mail this way and linking to these commits as a reference:
> >>>>>>
> >>>>>> https://reviews.freebsd.org/D13784
> >>>>>> https://svnweb.freebsd.org/base?view=revision&revision=332416
> >>>>>>
> >>>>>> So far I've tried to UEFI boot the 11.2 ISO and 12.0 ISO with the following Dell PowerEdge models without success:
> >>>>>>
> >>>>>> R440
> >>>>>> R630
> >>>>>> R430
> >>>>>> FC430
> >>>>>> R330
> >>>>>> R620
> >>>>>> R420
> >>>>>> R610
> >>>>>>
> >>>>>> -- 
> >>>>>> Med v?nlig h?lsning/Best Regards
> >>>>>> Linus Sundqvist
> >>>>>> System Engineer, Loopia AB
> >>>>>>
> >>>>> _______________________________________________
> >>>>> freebsd-current@freebsd.org mailing list
> >>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-current
> >>>>> To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
> >>>>>
> >>>>
> >>> _______________________________________________
> >>> freebsd-current@freebsd.org mailing list
> >>> https://lists.freebsd.org/mailman/listinfo/freebsd-current
> >>> To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
> >>>
> >>
> > _______________________________________________
> > freebsd-current@freebsd.org mailing list
> > https://lists.freebsd.org/mailman/listinfo/freebsd-current
> > To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
> > 
> 
-- End of PGP section, PGP failed!

-- 
Rod Grimes                                                 rgrimes@freebsd.org



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201807051720.w65HKTe4048658>