From owner-freebsd-questions Mon May 1 18: 4:35 2000 Delivered-To: freebsd-questions@freebsd.org Received: from gull.prod.itd.earthlink.net (gull.prod.itd.earthlink.net [207.217.121.85]) by hub.freebsd.org (Postfix) with ESMTP id E487E37B982; Mon, 1 May 2000 18:04:18 -0700 (PDT) (envelope-from eakeyson@earthlink.net) Received: from dell (ip232.stamford19.ct.pub-ip.psi.net [38.32.134.232]) by gull.prod.itd.earthlink.net (8.9.3/8.9.3) with SMTP id SAA13266; Mon, 1 May 2000 18:04:13 -0700 (PDT) From: "Edward W. Akeyson" To: Cc: Subject: 3.4-STABLE on IOPENER, no console output Date: Mon, 1 May 2000 21:04:12 -0400 Message-ID: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit X-Priority: 3 (Normal) X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook IMO, Build 9.0.2416 (9.0.2910.0) X-MimeOLE: Produced By Microsoft MimeOLE V5.00.2314.1300 Importance: Normal Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hello all: I am trying to get FreeBSD running on an Iopener, and am getting some strange behavior. I am running 3.4-STBLE, but during boot the screen and keyboard stop responding. It gets to "Booting [kernel]..." and then stops responding. However, it boots fine (I can hear the hard drive spin) and I can telnet and FTP into it from the server to which it is attached by PLIP. I have included the dmesg output and my kernel config file below. It is as if it is sending output to the serial console, and I do not want this. I haven't hooked up anything to the serial line, as this requires some interface circuitry first, so I don't know if this is the case really. I have tried "boot -h" at the boot: prompt trying to toggle it back to console output. Interestingly, in dmesg it says vga and sc0 not found although I know they are there and seen elsewhere in 4.0-STABLE on the same hardware(dmesg output for 4.0-stable can be seen here: http://www.kenseglerdesigns.com/cgi-bin/UltraBoard/UltraBoard.pl?Action=Show Post&Board=technical&Post=115&Idle=0&Sort=0&Order=Descend&Page=0&Session= ). I downloaded a Linux image to the Sandisk and it works the console fine. I will go to 4.0 if necessary, but I just want to know if this is a hardware problem (did I get a bum unit?) or a version problem. Could it be something else? Anyone know how I can solve this problem so that I can get on with my life!!! Script started on Mon May 1 20:54:02 2000 twinhead# uname -a FreeBSD twinhead.podunk.net 3.4-STABLE FreeBSD 3.4-STABLE #2: Mon May 1 18:49:32 GMT 2000 root@twinhead.podunk.net:/usr/src/sys/compile/IOPENER i386 twinhead# dmesg Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.4-STABLE #2: Mon May 1 18:49:32 GMT 2000 root@twinhead.podunk.net:/usr/src/sys/compile/IOPENER Timecounter "i8254" frequency 1193182 Hz CPU: IDT WinChip C6 (200.46-MHz 586-class CPU) Origin = "CentaurHauls" Id = 0x541 Stepping = 1 Features=0x8000b5 real memory = 31457280 (30720K bytes) avail memory = 28164096 (27504K bytes) Preloaded elf kernel "kernel" at 0xc028e000. Probing for devices on PCI bus 0: chip0: rev 0x03 on pci0.0.0 chip1: rev 0x00 on pci0.1.0 chip2: rev 0x1b on pci0.7.0 ide_pci0: rev 0x06 on pci0.7.1 chip3: rev 0x20 on pci0.7.4 Probing for devices on PCI bus 1: vga0: rev 0x5c int a irq 15 on pci1.0.0 Probing for PnP devices: CSN 1 Vendor ID: YMH0020 [0x2000a865] Serial 0xffffffff Comp ID: @@@0000 [0x00000000] Probing for devices on the ISA bus: sc0 not found atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa psm0 not found sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A, console sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): wd0: 2145MB (4394880 sectors), 4360 cyls, 16 heads, 63 S/T, 512 B/S wdc0: unit 1 (wd1): wd1: 15MB (31360 sectors), 490 cyls, 2 heads, 32 S/T, 512 B/S wdc1 not found at 0x170 ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode lpt0: on ppbus 0 lpt0: Interrupt-driven port ppi0: on ppbus 0 plip0: on ppbus 0 vga0 not found npx0 on motherboard npx0: INT 16 interface changing root device to wd0s1a twinhead# cat /sys/i386/conf/IOPENER # # IOPENER- ide disks, etc # # For more information read the handbook part System Administration -> # Configuring the FreeBSD Kernel -> The Configuration File. # The handbook is available in /usr/share/doc/handbook or online as # latest version from the FreeBSD World Wide Web server # # # An exhaustive list of options and more detailed explanations of the # device lines is present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $Id: GENERIC,v 1.143.2.12 1999/05/14 15:12:26 jkh Exp $ machine "i386" #cpu "I386_CPU" cpu "I486_CPU" cpu "I586_CPU" cpu "I686_CPU" ident GENERIC maxusers 32 options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options MFS_ROOT #MFS usable as root device, "MFS" req'ed options NFS #Network Filesystem options NFS_ROOT #NFS usable as root device, "NFS" req'ed options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on wd0 # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=24 # number of INTs controller isa0 controller pnp0 controller eisa0 controller pci0 #controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 #disk fd0 at fdc0 drive 0 #disk fd1 at fdc0 drive 1 options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 disk wd2 at wdc1 drive 0 disk wd3 at wdc1 drive 1 options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM #device acd0 #IDE CD-ROM #device wfd0 #IDE Floppy (e.g. LS-120) # A single entry for any of these controllers (ncr, ahb, ahc) is # sufficient for any number of installed devices. #controller ncr0 #controller ahb0 #controller ahc0 #controller isp0 # This controller offers a number of configuration options, too many to # document here - see the LINT file in this directory and look up the # dpt0 entry there for much fuller documentation on this. #controller dpt0 #controller adv0 at isa? port ? cam irq ? #controller adw0 #controller bt0 at isa? port ? cam irq ? #controller aha0 at isa? port ? cam irq ? #controller scbus0 #device da0 #device sa0 #device pass0 #device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 #device mcd0 at isa? port 0x300 bio irq 10 #controller matcd0 at isa? port 0x230 bio #device scd0 at isa? port 0x230 bio # atkbdc0 controlls both the keyboard and the PS/2 mouse controller atkbdc0 at isa? port IO_KBD tty device atkbd0 at isa? tty irq 1 device psm0 at isa? tty irq 12 device vga0 at isa? port ? conflicts # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? tty # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? tty #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std device npx0 at isa? port IO_NPX irq 13 # # Laptop support (see LINT for more options) # device apm0 at isa? disable flags 0x31 # Advanced Power Management # PCCARD (PCMCIA) support #controller card0 #device pcic0 at card? #device pcic1 at card? device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" tty irq 3 #device sio2 at isa? disable port "IO_COM3" tty irq 5 #device sio3 at isa? disable port "IO_COM4" tty irq 9 # Parallel port device ppc0 at isa? port? flags 0x40 net irq 7 controller ppbus0 device lpt0 at ppbus? device plip0 at ppbus? device ppi0 at ppbus? #controller vpo0 at ppbus? # # The following Ethernet NICs are all PCI devices. # #device ax0 # ASIX AX88140A #device de0 # DEC/Intel DC21x4x (``Tulip'') #device fxp0 # Intel EtherExpress PRO/100B (82557, 82558) #device mx0 # Macronix 98713/98715/98725 (``PMAC'') #device pn0 # Lite-On 82c168/82c169 (``PNIC'') #device rl0 # RealTek 8129/8139 #device tl0 # Texas Instruments ThunderLAN #device tx0 # SMC 9432TX (83c170 ``EPIC'') #device vr0 # VIA Rhine, Rhine II #device vx0 # 3Com 3c590, 3c595 (``Vortex'') #device wb0 # Winbond W89C840F #device xl0 # 3Com 3c90x (``Boomerang'', ``Cyclone'') # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. #device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 #device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000 #device ep0 at isa? port 0x300 net irq 10 #device ex0 at isa? port? net irq? #device fe0 at isa? port 0x300 net irq ? #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 #device lnc0 at isa? port 0x280 net irq 10 drq 0 #device ze0 at isa? port 0x300 net irq 10 iomem 0xd8000 #device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 #device cs0 at isa? port 0x300 net irq ? pseudo-device loop pseudo-device ether pseudo-device sl 1 pseudo-device ppp 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory and message queues. # options SYSVSHM options SYSVMSG options SYSVSEM # The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be # aware of the legal and administrative consequences of enabling this # option. The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. #pseudo-device bpfilter 4 #Berkeley packet filter twinhead# exit Script done on Mon May 1 20:54:51 2000 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message