Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 23 Feb 2009 18:13:53 -0200
From:      Gonzalo Nemmi <gnemmi@gmail.com>
To:        freebsd-questions@freebsd.org
Subject:   Re: broadcom wireless card BCM94311MCG on FreeBSD 7.1
Message-ID:  <200902231813.53482.gnemmi@gmail.com>
In-Reply-To: <9a52b1190902230851j32a91ea3n130af1d780945ec3@mail.gmail.com>
References:  <9a52b1190902230851j32a91ea3n130af1d780945ec3@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Monday 23 February 2009 2:51:05 pm Saifi Khan wrote:
> Hi all:
>
> Compaq C301TU laptop has a Broadcom chipset based wireless card and
> i'm unable to make it work on FreeBSD 7.1
>
> Using the ndisgen approach with bcm5wls.sys and bcm5wls.inf files
> creates a driver file which on kldload causes a kernel panic.
>
> Interestingly on the same laptop, there is a ethernet card of RTL
> 8139, which is also not detected by FreeBSD 7.1 . However, lets not
> worry about that for the time being.
>
> With Gentoo Linux, i've configured the Linux kernel to use the native
> bcm43xx driver and using the bcm43xx-fwcutter, i've been able to
> install the firmware and get the wireless card to work.
>
> Here is the lspci -v -nn details as collected from the Linux side.
>
> 06:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan
> mini-PCI (rev 01)
>         Subsystem: Hewlett-Packard Company Unknown device 1364
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
>         Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0, Cache Line Size: 64 bytes
>         Interrupt: pin A routed to IRQ 17
>         Region 0: Memory at 88000000 (32-bit, non-prefetchable) [size=16K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>         Capabilities: [58] Message Signalled Interrupts: Mask- 64bit-
> Queue=0/0 Enable-
>                 Address: 00000000  Data: 0000
>         Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00
>                 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1 unlimited
>                         ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>                 DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
>                         RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
>                         MaxPayload 128 bytes, MaxReadReq 128 bytes
>                 DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
>                 LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s,
> Latency L0 <4us, L1 <64us
>                         ClockPM- Suprise- LLActRep- BwNot-
>                 LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
>                         ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>                 LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive- BWMgmt- ABWMgmt-
>         Capabilities: [100] Advanced Error Reporting <?>
>         Capabilities: [13c] Virtual Channel <?>
>         Kernel driver in use: bcm43xx
>         Kernel modules: bcm43xx
>
> i don't intend to buy another wireless add-on card or another old laptop.
>
> Would be thankful, if anybody can suggest how i can get the Wireless
> card work to with FreeBSD 7.1 or FreeBSD 8.0 snapshot.
> Additional tips for getting the ethernet card to work will also be
> appreciated.

You should take a look in here if your trying to get the BCM4311 up and 
running: http://forums.freebsd.org/showthread.php?t=170&highlight=BCM

RTL 8139 seems to be fully supported on 7.1 .. just take a look 
at: /sys/dev/re/if_re.c

Regards
-- 
Blessings
Gonzalo Nemmi



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200902231813.53482.gnemmi>