Date: Sat, 27 Feb 1999 08:22:41 +0100 (MET) From: Martin Husemann <martin@rumolt.teuto.de> To: freebsd-stable@freebsd.org Subject: Install doesn't work Message-ID: <199902270722.IAA03994@rumolt.teuto.de>
next in thread | raw e-mail | index | archive | help
Hello!
I tried to boot FreeBSD 3.1 stable (fetched form ftp.releng3 about February
20) on a machine here where I usualy run NetBSD on.
It didn't work, as during the "Probing for devices" phase there is a
kernel panic (integer divide) after a lot of ILLEGAL REQUEST messages
apparently from the SCSI driver probing the QIC tape. This tape device
has a quirks entry on NetBSD because it responds to all LUN's (without
that quirk it would attach as eight devices).
I can't disbale EISA devices in the kernel configuration, and can't block
SCSI devices, so is there any way around this?
Martin
P.S.: just for reference, this particualr machine runs NetBSD just fine,
dmesg output follows:
NetBSD 1.3I (RUMOLT) #0: Fri Feb 26 16:41:34 MET 1999
martin@asprian.teuto.de:/usr/src/sys-i4b/arch/i386/compile/RUMOLT
cpu0: Intel 486DX (486-class)
real mem = 33161216
avail mem = 29143040
using 430 buffers containing 1761280 bytes of memory
mainbus0 (root)
eisa0 at mainbus0
ahb0 at eisa0 slot 1: Adaptec AHA-1742A SCSI
ahb0: interrupting at irq 11
scsibus0 at ahb0: 8 targets, 8 luns per target
sd0 at scsibus0 targ 0 lun 0: <QUANTUM, LPS525S, 3100> SCSI2 0/direct fixed
sd0: 501MB, 2448 cyl, 6 head, 69 sec, 512 bytes/sect x 1027548 sectors
st0 at scsibus0 targ 3 lun 0: <CALIPER, CP150, 1.17> SCSI1 1/sequential removable
st0: drive empty
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-3501TA, 2694> SCSI2 5/cdrom removable
sd1 at scsibus0 targ 6 lun 0: <IBM, DCAS-34330, S65A> SCSI2 0/direct fixed
sd1: 4134MB, 8205 cyl, 6 head, 171 sec, 512 bytes/sect x 8467200 sectors
device ATI4400 at eisa0 slot 3 not configured
ep0 at eisa0 slot 4: 3Com 3Com 3C597 Fast Etherlink TX
ep0: interrupting at irq 10
ep0: address 00:10:4b:24:be:a8, 64KB word-wide FIFO, 3:1 Rx:Tx split
ep0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX (default 10baseT)
isa0 at mainbus0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns8250 or ns16450, no fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
we0 at isa0 port 0x300-0x31f iomem 0xe0000-0xe3fff irq 15
we0: WD8013EP Ethernet (16-bit)
we0: Ethernet address 00:00:c0:11:48:2d
npx0 at isa0 port 0xf0-0xff: using exception 16
vt0 at isa0 port 0x60-0x6f irq 1
vt0: generic, 80 col, color, 8 scr, mf2-kbd, [R3.32]
vt0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isic0 at isa0 port 0x340-0x347 irq 5
isic0: AVM A1 or AVM Fritz!Card
isic0: ISAC 2085 Version V2.3 (B3) (IOM-2)
isic0: HSCX 82525 Version A3
isic1 at isa0 port 0xd80-0xd87 irq 12
isic1: Teles S0/16.3
isic1: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
isic1: HSCX 82525 or 21525 Version 2.1
biomask 840 netmask 9c60 ttymask 9ce2
i4b: ISDN call control device attached
i4btrc: 2 ISDN trace device(s) attached
i4bctl: ISDN system control port attached
i4brbch: 4 raw B channel access device(s) attached
i4btel: 2 ISDN telephony interface device(s) attached
i4bipr: 2 IP over raw HDLC ISDN device(s) attached (VJ header compression)
i4bisppp: 2 ISDN SyncPPP device(s) attached
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
IP Filter: initialized. Default = pass all, Logging = disabled
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199902270722.IAA03994>