Date: Fri, 9 Jun 2000 11:13:47 -0700 (PDT) From: nxiv@my-deja.com To: freebsd-gnats-submit@FreeBSD.org Subject: kern/19148: Tape retensioning renders tape unusable on Archive 4586NP Message-ID: <20000609181347.C84B837C479@hub.freebsd.org>
next in thread | raw e-mail | index | archive | help
>Number: 19148 >Category: kern >Synopsis: Tape retensioning renders tape unusable on Archive 4586NP >Confidential: no >Severity: serious >Priority: high >Responsible: freebsd-bugs >State: open >Quarter: >Keywords: >Date-Required: >Class: sw-bug >Submitter-Id: current-users >Arrival-Date: Fri Jun 09 11:20:00 PDT 2000 >Closed-Date: >Last-Modified: >Originator: John C. Archambeau >Release: 3.4-RELEASE >Organization: >Environment: FreeBSD phirewall 3.4-RELEASE FreeBSD 3.4-RELEASE #3: Sun May 28 17:59:25 PDT 2000 nxiv@phirewall:/usr/src/sys/compile/THEWALL-SMP i386 >Description: An mt -f /dev/rsa0 retention causes the drive to fast forward the tape to the end then abort with an the following SCSI message and flashing amber drive light after a rewind is attempted; (sa0:ahc0:0:0:0): LOAD UNLOAD. CDB: 1b 0 0 0 3 0 (sa0:ahc0:0:0:0): HARDWARE FAILURE asc:44,af (sa0:ahc0:0:0:0): Vendor Specific ASCQ (sa0:ahc0:0:0:0): REWIND. CDB: 1 0 0 0 0 0 (sa0:ahc0:0:0:0): HARDWARE FAILURE asc:44,af (sa0:ahc0:0:0:0): Vendor Specific ASCQ -- output from camcontrol devlist -- phirewall# camcontrol devlist -v scbus-1 on xpt0 bus 0: < > at scbus-1 target -1 lun -1 (xpt0) scbus0 on ahc0 bus 0: <ARCHIVE Python 28849-XXX 4.CM> at scbus0 target 0 lun 0 (pass0,sa0) <ARCHIVE Python 28849-XXX 4.CM> at scbus0 target 0 lun 1 (pass1,ch0) < > at scbus0 target -1 lun -1 () scbus1 on ahc0 bus 1: < > at scbus1 target -1 lun -1 () scbus2 on bt0 bus 0: < > at scbus2 target -1 lun -1 () scbus3 on ahc1 bus 0: <QUANTUM FIREBALL ST6.4S 0F0C> at scbus3 target 0 lun 0 (pass2,da0) <PLEXTOR CD-ROM PX-6XCS 1.02> at scbus3 target 4 lun 0 (pass3,cd0) < > at scbus3 target -1 lun -1 () phirewall# -- output from dmesg -- Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.4-RELEASE #3: Sun May 28 17:59:25 PDT 2000 nxiv@phirewall:/usr/src/sys/compile/THEWALL-SMP Timecounter "i8254" frequency 1193182 Hz CPU: Pentium Pro (686-class CPU) Origin = "GenuineIntel" Id = 0x617 Stepping = 7 Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV> real memory = 67108864 (65536K bytes) config> di ed0 config> di wt0 No such device: wt0 Invalid command or syntax. Type `?' for help. config> di wdc0 No such device: wdc0 Invalid command or syntax. Type `?' for help. config> di wdc1 No such device: wdc1 Invalid command or syntax. Type `?' for help. avail memory = 61726720 (60280K bytes) Programming 16 pins in IOAPIC #0 EISA INTCONTROL = 00004c00 FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x000f0011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc02fe000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc02fe09c. Preloaded elf module "if_ef.ko" at 0xc02fe0ec. Preloaded elf module "nwfs.ko" at 0xc02fe18c. Pentium Pro MTRR support enabled eisa0: <MIC60 (System Board)> Probing for devices on the EISA bus ahc0: <Adaptec 274X SCSI host adapter> at 0x3c00-0x3cff irq 9 on eisa0 slot 3 ahc0: aic7770 >= Rev E, Twin Channel, A SCSI Id=7, B SCSI Id=7, primary A, 4/255 SCBs bt0: <Buslogic 74xC SCSI host adapter> at 0x330-0x333, 0x4c00-0x4cff irq 15 bt0: on eisa0 slot 4 bt0: BT-75xC FW Rev. 4.28A Wide SCSI Host Adapter, SCSI ID 7, 100 CCBs fea0: <DEC DEFEA EISA FDDI Controller> at 0x5000-0x51ff at 0xd2000-0xd23ff fea0: irq 11 on eisa0 slot 5 fea0: DEC DEFEA EISA FDDI DAS Controller fea0: FDDI address 08:00:2b:b6:90:2c, FW=3.10, HW=1, SMT V7.2 fea0: FDDI Port[A] = A (PMD = ANSI Multi-Mode), FDDI Port[B] = B (PMD = ANSI Mul ti-Mode) Probing for devices on PCI bus 0: chip0: <Intel 82440FX (Natoma) PCI and memory controller> rev 0x02 on pci0.0.0 chip1: <Intel 82375EB PCI-EISA bridge> rev 0x15 on pci0.7.0 ahc1: <Adaptec aic7880 Ultra SCSI adapter> rev 0x00 int a irq 14 on pci0.8.0 ahc1: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs vga0: <Cirrus Logic GD5436 SVGA controller> rev 0x00 on pci0.9.0 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 10 on pci0.19 .0 fxp0: Ethernet address 00:90:27:1f:80:4a Probing for PnP devices: Probing for devices on the ISA bus: sc0 on isa sc0: VGA color <16 virtual consoles, flags=0x0> atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa psm0 not found sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in fd1: 1.2MB 5.25in ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 plip0: <PLIP network interface> on ppbus 0 bt: unit number (1) too high bt1 not found at 0x334 vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa npx0 on motherboard npx0: INT 16 interface APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via pin 2 ncp_load: [210-213] Waiting 7 seconds for SCSI devices to settle SMP: AP CPU #1 Launched! sa0 at ahc0 bus 0 target 0 lun 0 sa0: <ARCHIVE Python 28849-XXX 4.CM> Removable Sequential Access SCSI-2 device sa0: 5.000MB/s transfers (5.000MHz, offset 15) da0 at ahc1 bus 0 target 0 lun 0 da0: <QUANTUM FIREBALL ST6.4S 0F0C> Fixed Direct Access SCSI-2 device da0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled da0: 6180MB (12657717 512 byte sectors: 255H 63S/T 787C) ch0 at ahc0 bus 0 target 0 lun 1 ch0: <ARCHIVE Python 28849-XXX 4.CM> Removable Changer SCSI-2 device ch0: 5.000MB/s transfers (5.000MHz, offset 15) ch0: 0 slots, 1 drive, 1 picker, 0 portals changing root device to da0s3a cd0 at ahc1 bus 0 target 4 lun 0 cd0: <PLEXTOR CD-ROM PX-6XCS 1.02> Removable CD-ROM SCSI-2 device cd0: 5.000MB/s transfers (5.000MHz, offset 15) cd0: Attempt to query device size failed: NOT READY, Medium not present fea0: Link Unavailable >How-To-Repeat: Install an Archive 4586NP and perform an mt -f /dev/rsa0 retension >Fix: >Release-Note: >Audit-Trail: >Unformatted: To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-bugs" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000609181347.C84B837C479>