Date: Mon, 30 Aug 1999 22:44:26 -0400 From: akhar <jolicom@videotron.ca> To: big-sky@altavista.net, Mark Einreinhof <mark@cx559415-a.ftwal1.fl.home.com>, Chris Cappuccio <chris@dqc.org>, "Joe \"Marcus\" Clarke" <marcus@miami.edu>, questions@FreeBSD.ORG, misc@openbsd.org Subject: Re: If I may ask for help again! Message-ID: <37CB4189.BBCB3862@videotron.ca> References: <000001bef27b$87607f60$0201010a@cmr.net>
next in thread | previous in thread | raw e-mail | index | archive | help
I have tried my bst to follow advice but it did not seem to help I did resort to doing a tcpdump of my different attempts to connect to the net via my Openbsd gateway here it goes: tetis.home.foo.1051 > sphinx.home.foo.domain: 1+ (35) sphinx.home.foo > tetis.home.foo : icmp: sphinx.home.foo udp port domain unreachable and the 1+ just gets incremented by one every time! my ipf.rules is pretty simple pass in from any to any pass out from any to any my ipnat.rules is: map xl0 192.168.0.0/24 -> 0/32 and below my other message where I list other configurations. Where did I go wrong!! Akhar (patheticly blind) > -----Original Message----- > From: akhar [mailto:jolicom@videotron.ca] > Sent: Sunday, August 29, 1999 2:39 PM > To: big-sky@altavista.net > Subject: If I may ask for help again! > > I have OpenBSD setup as my gateway and server for my network it > interfaces with the internet via cable modem on xl0 and with the > intranet on ne3. I have already inquired your help it did work! for an hour > or > so until I rebooted. Now > I'm stuck I don't know what is wrong! all I can say is that I can do a > tracert from an NT box to my ISP in 3 minutes with two hops: my gateway > and the ISP. here are listed some of my different files in /etc > resolv.conf > domain videotron.ca > nameserver 127.0.0.1 > nameserver 205.... (I can't quite remenber) > nameserver 205.... (samething) > > hosts: > 127.0.0.1 localhost > 127.0.0.1 sphinx.home.foo sphinx > 192.168.0.1 sphinx.home.foo sphinx > 192.168.0.2 tetis.home.foo sphinx #NT box > > mygate: > 192.168.0.1 > > myname: > sphinx > > sphinx# netstat -nr > Routing tables > > Internet: > Destination Gateway Flags Refs Use > Mtu Interface > default 24.200.141.1 UGS 0 44 > - xl0 > 24.200.141/24 link#2 UC 0 0 > - xl0 > 24.200.141.1 8:0:3e:16:1b:59 UHL 1 4 - > xl0 > 24.200.141.104 127.0.0.1 UGHS 0 0 - lo0 > > 127/8 127.0.0.1 UGRS 0 0 > - lo0 > 127.0.0.1 127.0.0.1 UH 3 24 > - lo0 > 192.168.0/24 link#1 UC 0 0 > - ne3 => > 192.168/16 127.0.0.0 URS 0 0 - > lo0 > 192.168.0.2 0:e0:29:39:19:db UHL 2 1408 - ne3 > 224/4 127.0.0.1 URS 0 > 0 - lo0 > > Encap: > Source address/netmask Port Destination address/netmask > Port Prot > o SA(Address/SPI/Proto) > > sphinx# ifconfig -a > lo0: flags=8009<UP,LOOPBACK,MULTICAST> > inet 127.0.0.1 netmask 0xff000000 > lo1: flags=8008<LOOPBACK,MULTICAST> > ne3: flags=8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> > media: Ethernet autoselect (10baseT) > inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 > xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> > media: Ethernet 10baseT (10baseT half-duplex) > inet 24.200.141.104 netmask 0xffffff00 broadcast 255.255.255.255 > > sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> > sl1: flags=c010<POINTOPOINT,LINK2,MULTICAST> > ppp0: flags=8010<POINTOPOINT,MULTICAST> > ppp1: flags=8010<POINTOPOINT,MULTICAST> > tun0: flags=10<POINTOPOINT> > tun1: flags=10<POINTOPOINT> > enc0: flags=8<LOOPBACK> > bridge0: flags=0<> > bridge1: flags=0<> > > What is wrong?? If possible could some give me an exemple of the content > of the different files related to networking and/or a checklist of what > to configure. > Thank you in advance > Akhar To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?37CB4189.BBCB3862>