Date: Fri, 1 Apr 2016 13:02:26 +0000 (UTC) From: istvan konya <cielo_white@yahoo.com> To: <freebsd-questions@freebsd.org> Subject: FreeBSD 9.1 with two RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet cards stop to work after heavy traffic Message-ID: <2132386933.803891.1459515746288.JavaMail.yahoo@mail.yahoo.com> References: <2132386933.803891.1459515746288.JavaMail.yahoo.ref@mail.yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hello, my FreeBSD 9.1 with two RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet cards stop to work after heavy traffic the server work fine from about 2 years, If the traffic don't exceed 100M everything is fine, in the past, the traffic can be up to 300M, but in the last 2 weeks the network cards stops to work after a few seconds of heavy traffic. No another changes was made in this last 2 weeks. re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3000-0x30ff mem 0xd0100000-0xd01000ff irq 17 at device 5.0 on pci2 re0: Chip rev. 0x10000000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-ma ster, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: b0:48:7a:80:0b:1d re1: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3400-0x34ff mem 0xd0100400-0xd01004ff irq 18 at device 7.0 on pci2 re1: Chip rev. 0x10000000 re1: MAC rev. 0x00000000 miibus1: <MII bus> on re1 rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-ma ster, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re1: Ethernet address: 64:66:b3:04:bb:13 ifconfig re0 re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether b0:48:7a:80:0b:1d inet 81.196.63.57 netmask 0xfffffff8 broadcast 81.196.63.63 inet6 fe80::b248:7aff:fe80:b1d%re0 prefixlen 64 scopeid 0x5 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (1000baseT <full-duplex>) status: active ifconfig re1 re1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 64:66:b3:04:bb:13 inet 82.77.49.188 netmask 0xffffffc0 broadcast 82.77.49.255 inet6 fe80::6666:b3ff:fe04:bb13%re1 prefixlen 64 scopeid 0x6 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (1000baseT <full-duplex,master>) status: active /etc/rc.conf ipv6_network_interfaces="none" # Default is auto ipv6_activate_all_interfaces="NO" # this is the default ifconfig_re1=" inet 82.77.49.188 netmask 255.255.255.192 broadcast 82.77.49.255" ifconfig_re0=" inet 81.196.63.57 netmask 255.255.255.248" gateway_enable="YES" static_routes="lan0" route_lan0="-net 81.196.63.56/29 81.196.63.57" defaultrouter="82.77.49.129" After reboot, everything is fine, when the traffic don't exceed 100M. Anyone can help me pls Thanks
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?2132386933.803891.1459515746288.JavaMail.yahoo>