From owner-freebsd-current Tue Feb 22 3:16:50 2000 Delivered-To: freebsd-current@freebsd.org Received: from picalon.gun.de (picalon.gun.de [192.109.159.1]) by hub.freebsd.org (Postfix) with ESMTP id DB1C737B65C for ; Tue, 22 Feb 2000 03:16:46 -0800 (PST) (envelope-from andreas@klemm.gtn.com) Received: (from uucp@localhost) by picalon.gun.de (8.9.3/8.9.3) id MAA19282; Tue, 22 Feb 2000 12:16:31 +0100 (MET) >Received: (from andreas@localhost) by klemm.gtn.com (8.9.3/8.9.3) id MAA07579; Tue, 22 Feb 2000 12:07:29 +0100 (CET) (envelope-from andreas) Date: Tue, 22 Feb 2000 12:07:29 +0100 From: Andreas Klemm To: Soren Schmidt Cc: current@FreeBSD.ORG Subject: Re: timeout problems HighPoint HPT366 ATA66 controller && 40 GB Diamond Max Plus Message-ID: <20000222120729.A5646@titan.klemm.gtn.com> References: <20000221235518.A998@titan.klemm.gtn.com> <200002220832.JAA00330@freebsd.dk> Mime-Version: 1.0 X-Mailer: Mutt 1.0.1i In-Reply-To: <200002220832.JAA00330@freebsd.dk>; from sos@freebsd.dk on Tue, Feb 22, 2000 at 09:32:43AM +0100 X-Operating-System: FreeBSD 4.0-CURRENT SMP X-Disclaimer: A free society is one where it is safe to be unpopular Content-Type: text/plain; charset=us-ascii Sender: owner-freebsd-current@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG On Tue, Feb 22, 2000 at 09:32:43AM +0100, Soren Schmidt wrote: > You have a config problem.... Oh ... > Now where did this come form: > > ata4: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000 > > ata4: mask=00 status0=ff status1=ff > > ata4: probe allocation failed > > > ata2-master: success setting up UDMA4 mode on HPT366 chip > > ad4: ATA-5 disk at ata2 as master > > ad4: 39082MB (80041248 sectors), 79406 cyls, 16 heads, 63 S/T, 512 B/S > > ad4: 16 secs/int, 1 depth queue, UDMA66 > > ad4: piomode=4 dmamode=2 udmamode=4 cblid=1 Hmmm... > > # ATA and ATAPI devices > > device ata0 at isa? port IO_WD1 irq 14 Thought, this would be necessary. > > #device ata1 at isa? port IO_WD2 irq 15 > > device ata > > device atadisk # ATA disk drives > > #device atapicd # ATAPI CDROM drives > > #device atapifd # ATAPI floppy drives > > #device atapist # ATAPI tape drives > > options ATA_STATIC_ID #Static device numbering > > #options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices > > make that: > > device ata > device atadisk > options ATA_STATIC_ID Will try that. BTW, I tried this night (til 5am *sigh*) to make the device run under the Boards IDE controller. To make that happen I did the (probably mistake), to set a cylinder limitation jumper and install a special BIOS on the disk using the MaxBlast software from Maxtors ftp site. Since then the disk only had 4111cyl/255heads/64sectors =66043215 sectors. Now the drive ran fine under Windows and FreeBSD, but when I removed the jumper on the disk and tried again the abit EIDE controller, the disk wasn't recognized anymore. O.k. at 5am I was f***ing tired... Did I do something wrong to my disk using this maxtor utility ? Does somebody know, if there is a magic trick, to remove the BIOS ? I'll now try, what FreeBSD says to the drive, when I install the new kernel and if I remove the jumpers... Andreas /// -- Andreas Klemm http://www.FreeBSD.ORG/~andreas http://www.freebsd.org/~fsmp/SMP/SMP.html powered by Symmetric MultiProcessor FreeBSD Get new songs from our band: http://www.freebsd.org/~andreas/64bits/index.html To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message