Date: Mon, 2 Jul 2007 11:14:57 GMT From: Keve Nagy <wforms@safe-mail.net> To: freebsd-gnats-submit@FreeBSD.org Subject: kern/114213: optical drive not detected in the 6.x series of FreeBSD/i386 Message-ID: <200707021114.l62BEvSq008426@www.freebsd.org> Resent-Message-ID: <200707021120.l62BK3np086034@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
>Number: 114213
>Category: kern
>Synopsis: optical drive not detected in the 6.x series of FreeBSD/i386
>Confidential: no
>Severity: non-critical
>Priority: low
>Responsible: freebsd-bugs
>State: open
>Quarter:
>Keywords:
>Date-Required:
>Class: sw-bug
>Submitter-Id: current-users
>Arrival-Date: Mon Jul 02 11:20:02 GMT 2007
>Closed-Date:
>Last-Modified:
>Originator: Keve Nagy
>Release: FreeBSD/i386 6.2-RELEASE-p4
>Organization:
>Environment:
FreeBSD/i386 6.2-RELEASE, 6.1-RELEASE, 6.0-RELEASE with generic kernel.
>Description:
Something seems to be seriously messed up with the handling/detection of optical disc drives in the 6.x series of FreeBSD (at least on intel PII/PIII type hardware configurations).
I discovered this a few weeks ago when I tried to update a FreeBSD 5.4 system to 6.2R.
This is a VIA chipset Slot-1 PIII/800 system, with two 40 pin ide connectors integrated on the motherboard. The system supports UATA133 mode with 80 wire cables. I have my 80 Gigabyte Samsung harddisk on primary-master and there is no device installed for primary-slave (an empty mobile rack is connected). Secondary-master is a Pioneer DVD-ROM (read only) and secondary-slave is an older 52x speed LG CD-ROM (also read only).
I had absolutely no problems under my old FreeBSD 5.4, but when I tried to install 6.2R I had to realize that my DVD drive is not detected. I asked help in comp.unix.bsd.freebsd.misc but no reply arrived for weeks, so I am reporting this as a defect.
Please see my included dmesg outputs from various systems and see how they detect the two optical drives!
All these dmesg outputs were generated on the same day and on the same hardware using the default (GENERIC) minimal install, with the only difference being the disk or partition (slice) where the actual test system was installed and run from.
* FreeBSD 4.11R identifies both the DVD-ROM and the CD-ROM fine. I was able to do the installation from the DVD-ROM as acd0.
* FreeBSD 5.5R identifies both the DVD-ROM and the CD-ROM fine. I was able to do the installation from the DVD-ROM as acd0.
* FreeBSD 6.2R could not identify the DVD-ROM, but it identified the CD-ROM as acd0. The install CD did boot from the DVD drive and the first few steps of the installation seem to work, up until I select installation media as CD/DVD. After newfs running on the disk, reading selected packages from source fails. Interestingly, it also fails if I move the installation CD from the DVD drive (which was not detected by the system) to the CD-ROM drive (which is supposed to be acd0). The test system had to be installed via FTP.
* FreeBSD 6.1R and FreeBSD 6.0R both behave the same way as 6.2R. None of the 6.x series "see" the DVD-ROM drive, and they set the CD-ROM as acd0.
Another system, an IBM Netfinity 5000 server with dual Slot-1 PIII/500 also suffers from this defect. Hence the assumption that it may be related to PII/PIII era systems.
The Netfinity 5000 has only one integrated 40 pin IDE connector with an old-rubbish CD-ROM (read only), connected as master. The disks are all SCSI disks using the integrated Adaptec adapter. When I boot from the FreeBSD 6.2R install CD the CD-ROM drive does not show up in dmesg, no acd0, therefore installation from CD is not possible. Again, this also boots from the CD and gets to the main installation menu, but because no acd0 is detected installation from CD doesn't work. However, boot CDs of Linux, NetBSD and OpenBSD (4.1) nicely detect the CD-ROM, as well as FreeBSD 4.11R.
Since this optical drive issue is working fine with 4.11R and 5.5R but not working with 6.0R, 6.1R and 6.2R, I assume that there is a little screw-up in the 6.x series.
It would be nice to see this fixed in the upcoming 6.3R !
##### FreeBSD 4.11-RELEASE (generic) dmesg:
-------------------------------------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE #0: Fri Jan 21 17:21:22 GMT 2005
root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel Pentium III (800.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 805240832 (786368K bytes)
avail memory = 777486336 (759264K bytes)
Preloaded elf kernel "kernel" at 0xc055c000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00fddf0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <ATI model 5159 graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C596B PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596 ATA66 controller> port 0xe000-0xe00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1: ATEN International product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd1 at ukbd0
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3050) at 7.3
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
rl0: Ethernet address: 00:40:f4:64:4d:d5
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
isa0: too many dependant configs (8)
isa0: unexpected small tag 14
orm0: <Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff,0xd4000-0xdafff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 76351MB <SAMSUNG SP0802N> [155127/16/63] at ata0-master UDMA66
acd0: DVD-ROM <Pioneer DVD-ROM ATAPIModel DVD-119 0105> at ata1-master PIO4
acd1: CDROM <GCR-8521B> at ata1-slave PIO4
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
##### FreeBSD 4.11-RELEASE (generic) verbose-dmesg:
---------------------------------------------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-RELEASE #0: Fri Jan 21 17:21:22 GMT 2005
root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 800063175 Hz, i8254 clock: 1193234 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Intel Pentium III (800.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 805240832 (786368K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009ffff, 651264 bytes (159 pages)
0x000583000 - 0x02ffe7fff, 799428608 bytes (195173 pages)
avail memory = 777486336 (759264K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fadc0
bios32: Entry = 0xfb240 (c00fb240) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb270
pnpbios: Found PnP BIOS data at 0xc00fbf30
pnpbios: Entry = f0000:bf58 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f7d50
Preloaded elf kernel "kernel" at 0xc055c000.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
Using $PIR table, 7 entries at 0xc00fddf0
pcib-: pcib0 exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x1106, dev=0x0691, revid=0x44
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d8000000, size 25
found-> vendor=0x1106, dev=0x8598, revid=0x00
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x1106, dev=0x0596, revid=0x23
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1106, dev=0x0571, revid=0x10
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000e000, size 4
found-> vendor=0x1106, dev=0x3038, revid=0x11
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=12
map[20]: type 1, range 32, base 0000e400, size 5
found-> vendor=0x1106, dev=0x3050, revid=0x30
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x10ec, dev=0x8139, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000e800, size 8
map[14]: type 1, range 32, base dd002000, size 8
found-> vendor=0x1033, dev=0x00e7, revid=0x01
class=0c-00-10, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base dd000000, size 12
found-> vendor=0x9004, dev=0x8178, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000ec00, size 8
map[14]: type 1, range 32, base dd001000, size 12
pci0: <PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x5159, revid=0x00
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base d0000000, size 27
map[14]: type 1, range 32, base 0000d000, size 8
map[18]: type 1, range 32, base db000000, size 16
pci1: <PCI bus> on pcib2
pci1: <ATI model 5159 graphics accelerator> (vendor=0x1002, dev=0x5159) at 0.0 irq 11
isab0: <VIA 82C596B PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596 ATA66 controller> port 0xe000-0xe00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xe000
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xe008
ata1: mask=03 ostat0=50 ostat2=50
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 14 eb
ata1: mask=03 stat0=00 stat1=00
ata1: devices=0c
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1: ATEN International product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3050) at 7.3
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
rl0: Ethernet address: 00:40:f4:64:4d:d5
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: rl0 attached
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: latency timer 32 -> 32.
fwohci0: cache size 8 -> 8.
using shared irq10.
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: resetting OHCI...done (loop=0)
fwohci0: phy read failed(1).
fwohci0: fwphy_rddata: 0x2 loop=1, retry=1
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xf800a002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
bpf: fwe0 attached
sbp0: <SBP-2/SCSI over FireWire> on firewire0
sbp_attach (cold=1)
sbp_post_busreset
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 449 instructions downloaded
ahc0: Features 0x10005, Bugs 0x25, Flags 0x20481540
using shared irq11.
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
pci-: pci1 exists, using next available unit number
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
CTL0045: start dependant
CTL0045: adding irq mask 0x20
CTL0045: adding dma mask 0x2
CTL0045: adding dma mask 0x20
CTL0045: adding io range 0x220-0x22f, size=0x10, align=0x1
CTL0045: adding io range 0x330-0x331, size=0x2, align=0x1
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependant
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependant
isa0: too many dependant configs (8)
CTL7002: start dependant
CTL7002: adding io range 0x200-0x207, size=0x8, align=0x1
CTL7002: start dependant
CTL7002: adding io range 0x200-0x20f, size=0x8, align=0x8
CTL7002: end dependant
CTL0022: start dependant
CTL0022: adding io range 0x620-0x623, size=0x4, align=0x1
CTL0022: start dependant
CTL0022: adding io range 0x620-0x683, size=0x4, align=0x20
CTL0022: end dependant
isa0: unexpected small tag 14
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff,0xd4000-0xdafff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0067
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 27 7e 4f 4f 82 51 03
b8 1f 00 4f 0e 0f 00 00 05 a0 90 03 8f 28 1f 8f
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 27 7e 4f 4f 82 51 03
b8 1f 00 4f 0e 0f 00 00 05 a0 90 03 8f 28 1f 8f
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x461 0x471 0x461 0x461
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x461 0x469 0x461 0x461
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x220 specified. Nearest valid baseport is 0x230. Failing probe.
unknown: <Audio> failed to probe at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq 1,5 on isa0
adv1: Invalid baseport of 0x200 specified. Nearest valid baseport is 0x210. Failing probe.
unknown: <Game> failed to probe at port 0x200-0x20f on isa0
adv1: Invalid baseport of 0x620 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <WaveTable> failed to probe at port 0x620-0x62f on isa0
Current DB 0
ch = 0
Current OP KEY INT BR len Addr Depend Stat: Cnt
2ea22000 OUTL ST2 ALL ALL 12 00000000 2ea22080 8411:000f RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: faith0 attached
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68d440, tty 63009a, net 670c9a
bpf: sl0 attached
ad0: success setting UDMA4 on VIA chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <SAMSUNG SP0802N/TK200-04> ATA-7 disk at ata0-master
ad0: 76351MB (156368016 sectors), 155127 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=4 dmaflag=1
ata1-master: success setting PIO4 on generic chip
acd0: <Pioneer DVD-ROM ATAPIModel DVD-119 0105/E1.05> DVD-ROM drive at ata1 as master
acd0: read 1594KB/s (37026KB/s), 256KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
ata1-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-slave: success setting PIO4 on generic chip
bus_explore done
sbp_post_explore (sbp_cold=2)
acd1: <GCR-8521B/1.02> CDROM drive at ata1 as slave
acd1: read 8937KB/s (48034KB/s), 128KB buffer, PIO4
acd1: Reads: CD-R, CD-RW, CD-DA stream, packet
acd1: Writes:
acd1: Audio: play, 255 volume levels
acd1: Mechanism: ejectable tray, unlocked, lock protected
acd1: Medium: no/blank disc
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:2:0): Sending WDTR 1
(ahc0:A:2:0): Received WDTR 1 filtered to 1
ahc0: target 2 using 16bit transfers
(ahc0:A:2:0): Sending SDTR period c, offset 8
(ahc0:A:2:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 2 synchronous at 20.0MHz, offset = 0x8
Creating DISK da0
pass0 at ahc0 bus 0 target 2 lun 0
pass0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
pass0: Serial Number 369929932513
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: Serial Number 369929932513
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 3903794, size 3903732 : OK
da0s2: type 0xb5, start 3903795, end = 7807589, size 3903795 : OK
da0s3: type 0xb5, start 7807590, end = 11711384, size 3903795 : OK
da0s4: type 0x5, start 11711385, end = 14635214, size 2923830 : OK
da0s5: type 0x83, start 11711448, end = 14635214, size 2923767 : OK
start_init: trying /sbin/init
##### FreeBSD 5.5-RELEASE (generic) dmesg:
------------------------------------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.5-RELEASE #0: Tue May 23 14:58:27 UTC 2006
root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (800.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 805240832 (767 MB)
avail memory = 778223616 (742 MB)
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <VIA692 AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0xe000-0xe00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, HOST-PCI> at device 7.3 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:40:f4:64:4d:d5
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
fwe0: Ethernet address: 02:00:4c:00:30:e1
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
orm0: <ISA Option ROMs> at iomem 0xd4000-0xdafff,0xd0000-0xd3fff,0xc0000-0xccfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
uhub1: ATEN International product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd1 at ukbd0
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
Timecounter "TSC" frequency 800032435 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 76351MB <SAMSUNG SP0802N/TK200-04> [155127/16/63] at ata0-master UDMA66
acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-119 0105/E1.05> at ata1-master PIO4
acd1: CDROM <GCR-8521B/1.02> at ata1-slave PIO4
Waiting 15 seconds for SCSI devices to settle
da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
Mounting root from ufs:/dev/da0s2a
##### FreeBSD 5.5-RELEASE (generic) verbose-dmesg:
--------------------------------------------------
0x0000000000001000 - 0x000000000009ffff, 651264 bytes (159 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000002f23ffff, 778153984 bytes (189979 pages)
avail memory = 778223616 (742 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fadc0
bios32: Entry = 0xfb240 (c00fb240) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb270
pnpbios: Found PnP BIOS data at 0xc00fbf30
pnpbios: Entry = f0000:bf58 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <VIA692 AWRDACPI> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
pcibios: BIOS version 2.10
Found $PIR table, 7 entries at 0xc00fddf0
PCI-Only Interrupts: 10 11 12
Location Bus Device Pin Link IRQs
slot 1 0 8 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 D 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 A 0x02 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 B 0x03 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 C 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 D 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 A 0x03 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 B 0x05 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 C 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 D 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 A 0x05 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 B 0x01 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 C 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 D 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 D 0x05 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x01 3 4 5 7 9 10 11 12 14 15
embedded 0 1 B 0x02 3 4 5 7 9 10 11 12 14 15
embedded 0 1 C 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 1 D 0x05 3 4 5 7 9 10 11 12 14 15
embedded 0 7 C 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 7 D 0x05 3 4 5 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
ACPI timer: 0/3 0/6 0/3 0/3 0/3 1/1 0/5 0/3 0/3 0/3 -> 1
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU (3 Cx states)> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x4010
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0
ACPI PCI link initial configuration:
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.8.0
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.8.1
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.8.2
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.8.3
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.9.0
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.9.1
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.9.2
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.9.3
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.10.0
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.10.1
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.10.2
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.10.3
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.11.0
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.11.1
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.11.2
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.11.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.12.0
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.12.1
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.12.2
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.12.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 11+ low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 10+ low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 0+ low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 0: [ 1 3 4 5 6 7 10 11 12 14 15] 12+ low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base d8000000, size 25, enabled
found-> vendor=0x1106, dev=0x0691, revid=0x44
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x8598, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0596, revid=0x23
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000e000, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x10
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000e400, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.LNKD)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKA (references 7, priority 145173):
interrupts: 11 10 5 12 7 6 4 3 15 14 1
penalty: 280 280 330 5280 5280 5280 5280 5280 50280 50280100280
\\_SB_.PCI0.LNKB (references 7, priority 145173):
interrupts: 11 10 5 12 7 6 4 3 15 14 1
penalty: 280 280 330 5280 5280 5280 5280 5280 50280 50280100280
\\_SB_.PCI0.LNKC (references 7, priority 145173):
interrupts: 11 10 5 12 7 6 4 3 15 14 1
penalty: 280 280 330 5280 5280 5280 5280 5280 50280 50280100280
\\_SB_.PCI0.LNKD (references 7, priority 145173):
interrupts: 11 10 5 12 7 6 4 3 15 14 1
penalty: 280 280 330 5280 5280 5280 5280 5280 50280 50280100280
pcib0: slot 7 INTD routed to irq 12 via \\_SB_.PCI0.LNKD
found-> vendor=0x1106, dev=0x3038, revid=0x11
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=12
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3050, revid=0x30
bus=0, slot=7, func=3
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 0000e800, size 8, enabled
map[14]: type 1, range 32, base dd002000, size 8, enabled
pcib0: matched entry for 0.8.INTA (src \\_SB_.PCI0.LNKA)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKA (references 7, priority 147178):
interrupts: 11 10 5 7 6 4 3 12 15 14 1
penalty: 560 560 610 5560 5560 5560 5560 5630 50560 50560100560
\\_SB_.PCI0.LNKB (references 7, priority 147178):
interrupts: 11 10 5 7 6 4 3 12 15 14 1
penalty: 560 560 610 5560 5560 5560 5560 5630 50560 50560100560
\\_SB_.PCI0.LNKC (references 7, priority 147178):
interrupts: 11 10 5 7 6 4 3 12 15 14 1
penalty: 560 560 610 5560 5560 5560 5560 5630 50560 50560100560
pcib0: slot 8 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found-> vendor=0x10ec, dev=0x8139, revid=0x10
bus=0, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dd000000, size 12, enabled
pcib0: matched entry for 0.9.INTA (src \\_SB_.PCI0.LNKB)
pcib0: possible interrupts: 1 3 4 5 6 7 10 11 12 14 15
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKB (references 7, priority 149182):
interrupts: 10 5 11 7 6 4 3 12 15 14 1
penalty: 840 890 910 5840 5840 5840 5840 5910 50840 50840100840
\\_SB_.PCI0.LNKC (references 7, priority 149182):
interrupts: 10 5 11 7 6 4 3 12 15 14 1
penalty: 840 890 910 5840 5840 5840 5840 5910 50840 50840100840
pcib0: slot 9 INTA routed to irq 10 via \\_SB_.PCI0.LNKB
found-> vendor=0x1033, dev=0x00e7, revid=0x01
bus=0, slot=9, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000ec00, size 8, enabled
map[14]: type 1, range 32, base dd001000, size 12, enabled
pcib0: matched entry for 0.12.INTA (src \\_SB_.PCI0.LNKA)
pcib0: slot 12 INTA is already routed to irq 11
found-> vendor=0x9004, dev=0x8178, revid=0x00
bus=0, slot=12, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
agp0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xd8000000
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xda000000-0xdbffffff
pcib1: prefetched decode 0xd0000000-0xd7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base d0000000, size 27, enabled
pcib1: device (null) requested decoded memory range 0xd0000000-0xd7ffffff
map[14]: type 4, range 32, base 0000d000, size 8, enabled
pcib1: device (null) requested decoded I/O range 0xd000-0xd0ff
map[18]: type 1, range 32, base db000000, size 16, enabled
pcib1: device (null) requested decoded memory range 0xdb000000-0xdb00ffff
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.LNKA)
pcib0: slot 1 INTA is already routed to irq 11
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5159, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0xe000-0xe00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe000
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe400
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, HOST-PCI> at device 7.3 (no driver attached)
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
rl0: Ethernet address: 00:40:f4:64:4d:d5
rl0: [MPSAFE]
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdd000000
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
fwe0: bpf attached
fwe0: Ethernet address: 02:00:4c:00:30:e1
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xec00
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 449 instructions downloaded
ahc0: Features 0x10005, Bugs 0x25, Flags 0x20481540
ahc0: [GIANT-LOCKED]
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: irq maps: 0x401 0x411 0x401 0x401
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0x401 0x409 0x401 0x401
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
CTL0045: start dependent (0)
CTL0045: adding irq mask 0x20
CTL0045: adding dma mask 0x2
CTL0045: adding dma mask 0x20
CTL0045: adding io range 0x220-0x22f, size=0x10, align=0x1
CTL0045: adding io range 0x330-0x331, size=0x2, align=0x1
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependent (2)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x10
CTL0045: adding io range 0x388-0x397, size=0x4, align=0x4
CTL0045: end dependent
CTL7002: start dependent (0)
CTL7002: adding io range 0x200-0x207, size=0x8, align=0x1
CTL7002: start dependent (1)
CTL7002: adding io range 0x200-0x20f, size=0x8, align=0x8
CTL7002: end dependent
CTL0022: start dependent (0)
CTL0022: adding io range 0x620-0x623, size=0x4, align=0x1
CTL0022: start dependent (1)
CTL0022: adding io range 0x620-0x683, size=0x4, align=0x20
CTL0022: end dependent
ex_isa_identify()
unknown: status reg test failed fe
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 14: ioport 0xec00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xd4000-0xdafff,0xd0000-0xd3fff,0xc0000-0xccfff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 27 7e 4f 4f 82 51 03
b8 1f 00 4f 0e 0f 00 00 07 80 90 03 8f 28 1f 8f
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 27 7e 4f 4f 82 51 03
b8 1f 00 4f 0e 0f 00 00 07 80 90 03 8f 28 1f 8f
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x220 specified. Nearest valid baseport is 0x230. Failing probe.
unknown: <Audio> failed to probe at port 0x388-0x38b,0x330-0x331,0x220-0x22f irq 5 drq 5,1 on isa0
adv1: Invalid baseport of 0x200 specified. Nearest valid baseport is 0x210. Failing probe.
unknown: <Game> failed to probe at port 0x200-0x207 on isa0
adv1: Invalid baseport of 0x620 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <WaveTable> failed to probe at port 0x620-0x623 on isa0
uhub1: ATEN International product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 800034252 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on VIA 82C596B chip
ata0-master: setting UDMA66 on VIA 82C596B chip
ad0: <SAMSUNG SP0802N/TK200-04> ATA-7 disk at ata0-master
ad0: 76351MB (156368016 sectors), 155127 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
GEOM: new disk ad0
ar: FreeBSD check1 failed
ata1-slave: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata1-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin
ata1-master: setting PIO4 on VIA 82C596B chip
ata1-slave: setting PIO4 on VIA 82C596B chip
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):611/254/63 s:63 l:9831717
[1] f:00 typ:6 s(CHS):612/0/1 e(CHS):651/254/63 s:9831780 l:642600
[2] f:00 typ:15 s(CHS):652/0/1 e(CHS):1023/254/63 s:10474380 l:104936580
[3] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:115410960 l:40949685
GEOM: Configure ad0s1, start 32256 length 5033839104 end 5033871359
GEOM: Configure ad0s2, start 5033871360 length 329011200 end 5362882559
GEOM: Configure ad0s3, start 5362882560 length 53727528960 end 59090411519
GEOM: Configure ad0s4, start 59090411520 length 20966238720 end 80056650239
MBREXT Slice 5 on ad0s3:
[0] f:00 typ:6 s(CHS):652/1/1 e(CHS):777/254/63 s:63 l:2024127
[1] f:00 typ:5 s(CHS):778/0/1 e(CHS):1023/254/63 s:2024190 l:4096575
GEOM: Configure ad0s5, start 32256 length 1036353024 end 1036385279
MBREXT Slice 6 on ad0s3:
[0] f:00 typ:6 s(CHS):778/1/1 e(CHS):1023/254/63 s:63 l:4096512
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:6120765 l:30716280
GEOM: Configure ad0s6, start 1036417536 length 2097414144 end 3133831679
MBREXT Slice 7 on ad0s3:
[0] f:00 typ:7 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:30716217
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:36837045 l:36869175
GEOM: Configure ad0s7, start 3133863936 length 15726703104 end 18860567039
MBREXT Slice 8 on ad0s3:
[0] f:00 typ:7 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:36869112
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s8, start 18860599296 length 18876985344 end 37737584639
GEOM: Configure ad0s4a, start 0 length 536870912 end 536870911
GEOM: Configure ad0s4b, start 536870912 length 268435456 end 805306367
GEOM: Configure ad0s4c, start 0 length 20966238720 end 20966238719
GEOM: Configure ad0s4d, start 805306368 length 536870912 end 1342177279
GEOM: Configure ad0s4e, start 1342177280 length 536870912 end 1879048191
GEOM: Configure ad0s4f, start 1879048192 length 19087190528 end 20966238719
acd0: <Pioneer DVD-ROM ATAPIModel DVD-119 0105/E1.05> DVDROM drive at ata1 as master
acd0: read 1594KB/s (6894KB/s), 256KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
acd1: <GCR-8521B/1.02> CDROM drive at ata1 as slave
acd1: read 8937KB/s (8937KB/s), 128KB buffer, PIO4
acd1: Reads: CDR, CDRW, CDDA stream, packet
acd1: Writes:
acd1: Audio: play, 255 volume levels
acd1: Mechanism: ejectable tray, unlocked, lock protected
acd1: Medium: no/blank disc
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
[0] f:61 typ:116 s(CHS):288/110/36 e(CHS):366/104/37 s:1701998624 l:1629516659
[1] f:6e typ:101 s(CHS):107/121/32 e(CHS):10/121/13 s:1330184192 l:538976288
[2] f:20 typ:83 s(CHS):345/32/19 e(CHS):324/77/19 s:538989391 l:1398362912
[3] f:7f typ:187 s(CHS):65/1/0 e(CHS):128/0/7 s:-384957826 l:65344
[0] f:61 typ:116 s(CHS):288/110/36 e(CHS):366/104/37 s:1701998624 l:1629516659
[1] f:6e typ:101 s(CHS):107/121/32 e(CHS):10/121/13 s:1330184192 l:538976288
[2] f:20 typ:83 s(CHS):345/32/19 e(CHS):324/77/19 s:538989391 l:1398362912
[3] f:7f typ:187 s(CHS):65/1/0 e(CHS):128/0/7 s:-384957826 l:65344
[0] f:69 typ:116 s(CHS):357/115/43 e(CHS):288/116/37 s:543452769 l:1953719666
[1] f:61 typ:10 s(CHS):269/114/52 e(CHS):357/116/40 s:1937339168 l:778921332
[2] f:0d typ:0 s(CHS):23/10/0 e(CHS):340/92/14 s:542262348 l:1663071081
[3] f:6f typ:101 s(CHS):370/109/48 e(CHS):357/115/51 s:168636004 l:0
[0] f:69 typ:116 s(CHS):357/115/43 e(CHS):288/116/37 s:543452769 l:1953719666
[1] f:61 typ:10 s(CHS):269/114/52 e(CHS):357/116/40 s:1937339168 l:778921332
[2] f:0d typ:0 s(CHS):23/10/0 e(CHS):340/92/14 s:542262348 l:1663071081
[3] f:6f typ:101 s(CHS):370/109/48 e(CHS):357/115/51 s:168636004 l:0
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
ahc0: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahc0: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:5. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahc0: Selection Timeout on A:8. 0 SCBs aborted
ahc0: Selection Timeout on A:9. 0 SCBs aborted
ahc0: Selection Timeout on A:10. 0 SCBs aborted
ahc0: Selection Timeout on A:11. 0 SCBs aborted
ahc0: Selection Timeout on A:12. 0 SCBs aborted
ahc0: Selection Timeout on A:13. 0 SCBs aborted
ahc0: Selection Timeout on A:14. 0 SCBs aborted
ahc0: Selection Timeout on A:15. 0 SCBs aborted
(probe9:ahc0:0:2:0): Retrying Command
(ahc0:A:2:0): Sending WDTR 1
(ahc0:A:2:0): Received WDTR 1 filtered to 1
ahc0: target 2 using 16bit transfers
(ahc0:A:2:0): Sending SDTR period c, offset 8
(ahc0:A:2:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 2 synchronous at 20.0MHz, offset = 0x8
pass0 at ahc0 bus 0 target 2 lun 0
pass0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
pass0: Serial Number 369929932513
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: Serial Number 369929932513
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
GEOM: new disk da0
[0] f:00 typ:181 s(CHS):0/1/1 e(CHS):242/254/63 s:63 l:3903732
[1] f:80 typ:165 s(CHS):243/0/1 e(CHS):485/254/63 s:3903795 l:3903795
[2] f:00 typ:181 s(CHS):486/0/1 e(CHS):728/254/63 s:7807590 l:3903795
[3] f:00 typ:5 s(CHS):729/0/1 e(CHS):910/254/63 s:11711385 l:2923830
GEOM: Configure da0s1, start 32256 length 1998710784 end 1998743039
GEOM: Configure da0s2, start 1998743040 length 1998743040 end 3997486079
GEOM: Configure da0s3, start 3997486080 length 1998743040 end 5996229119
GEOM: Configure da0s4, start 5996229120 length 1497000960 end 7493230079
GEOM: Configure da0s2a, start 0 length 1782579200 end 1782579199
GEOM: Configure da0s2b, start 1782579200 length 216163840 end 1998743039
GEOM: Configure da0s2c, start 0 length 1998743040 end 1998743039
MBREXT Slice 5 on da0s4:
[0] f:80 typ:131 s(CHS):729/1/1 e(CHS):910/254/63 s:63 l:2923767
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s5, start 32256 length 1496968704 end 1497000959
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
Mounting root from ufs:/dev/da0s2a
start_init: trying /sbin/init
##### FreeBSD 6.2-RELEASE (generic) dmesg:
------------------------------------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (800.04-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 805240832 (767 MB)
avail memory = 778620928 (742 MB)
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <VIA692 AWRDACPI> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x407f,0x4080-0x40ff,0x5000-0x500f on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, HOST-PCI> at device 7.3 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:40:f4:64:4d:d5
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
fwe0: Ethernet address: 02:00:4c:00:30:e1
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
ahc0: [GIANT-LOCKED]
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff,0xd4000-0xdafff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
uhub1: vendor 0x0557 product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd2 at ukbd0
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: vendor 0x0451 product 0x2046, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
Timecounter "TSC" frequency 800035201 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 76351MB <SAMSUNG SP0802N TK200-04> at ata0-master UDMA66
unknown: timeout waiting for read DRQ
unknown: timeout waiting for read DRQ
acd0: CDROM <GCR-8521B/1.02> at ata1-slave PIO4
Waiting 5 seconds for SCSI devices to settle
da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
Trying to mount root from ufs:/dev/da0s3a
##### FreeBSD 6.2-RELEASE (generic) verbose-dmesg:
--------------------------------------------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0b52000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0b5216c.
Calibrating clock(s) ... i8254 clock: 1193232 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 800033938 Hz
CPU: Intel Pentium III (800.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 805240832 (767 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009ffff, 651264 bytes (159 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000002f229fff, 778063872 bytes (189957 pages)
avail memory = 778620928 (742 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fadc0
bios32: Entry = 0xfb240 (c00fb240) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb270
pnpbios: Found PnP BIOS data at 0xc00fbf30
pnpbios: Entry = f0000:bf58 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Jan 12 2007 10:40:02)
npx0: INT 16 interface
acpi0: <VIA692 AWRDACPI> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
pcibios: BIOS version 2.10
Found $PIR table, 7 entries at 0xc00fddf0
PCI-Only Interrupts: 10 11 12
Location Bus Device Pin Link IRQs
slot 1 0 8 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 D 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 A 0x02 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 B 0x03 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 C 0x05 3 4 5 7 9 10 11 12 14 15
slot 2 0 9 D 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 A 0x03 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 B 0x05 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 C 0x01 3 4 5 7 9 10 11 12 14 15
slot 3 0 10 D 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 A 0x05 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 B 0x01 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 C 0x02 3 4 5 7 9 10 11 12 14 15
slot 4 0 11 D 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 5 0 12 D 0x05 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x01 3 4 5 7 9 10 11 12 14 15
embedded 0 1 B 0x02 3 4 5 7 9 10 11 12 14 15
embedded 0 1 C 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 1 D 0x05 3 4 5 7 9 10 11 12 14 15
embedded 0 7 C 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 7 D 0x05 3 4 5 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd3c57000 pa 0x9e000
ACPI timer: 0/3 0/5 0/3 1/1 0/3 0/3 0/5 0/3 0/3 0/3 -> 1
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 12 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 12 N 0 1 3 4 5 6 7 10 11 12 14 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 1 3 4 5 6 7 10 11 12 14 15
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x4010
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x407f,0x4080-0x40ff,0x5000-0x500f on acpi0
ACPI: Found matching pin for 0.8.INTA at func 0: 11
ACPI: Found matching pin for 0.9.INTA at func 0: 10
ACPI: Found matching pin for 0.12.INTA at func 0: 11
ACPI: Found matching pin for 0.7.INTD at func 2: 12
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1106, dev=0x0691, revid=0x44
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base d8000000, size 25, enabled
found-> vendor=0x1106, dev=0x8598, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0596, revid=0x23
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0571, revid=0x10
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000e000, size 4, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x11
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=12
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000e400, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 7 INTD routed to irq 12 via \\_SB_.PCI0.LNKD
found-> vendor=0x1106, dev=0x3050, revid=0x30
bus=0, slot=7, func=3
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10ec, dev=0x8139, revid=0x10
bus=0, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 8, enabled
map[14]: type 1, range 32, base dd002000, size 8, enabled
pcib0: matched entry for 0.8.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 8 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found-> vendor=0x1033, dev=0x00e7, revid=0x01
bus=0, slot=9, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dd000000, size 12, enabled
pcib0: matched entry for 0.9.INTA (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 9 INTA routed to irq 10 via \\_SB_.PCI0.LNKB
found-> vendor=0x9004, dev=0x8178, revid=0x00
bus=0, slot=12, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
map[10]: type 4, range 32, base 0000ec00, size 8, enabled
map[14]: type 1, range 32, base dd001000, size 12, enabled
pcib0: matched entry for 0.12.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 12 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd8000000-0xd9ffffff at device 0.0 on pci0
agp0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xd8000000
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xda000000-0xdbffffff
pcib1: prefetched decode 0xd0000000-0xd7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5159, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base d0000000, size 27, enabled
pcib1: (null) requested memory range 0xd0000000-0xd7ffffff: good
map[14]: type 4, range 32, base 0000d000, size 8, enabled
pcib1: (null) requested I/O range 0xd000-0xd0ff: in range
map[18]: type 1, range 32, base db000000, size 16, enabled
pcib1: (null) requested memory range 0xdb000000-0xdb00ffff: good
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C596B UDMA66 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe400
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, HOST-PCI> at device 7.3 (no driver attached)
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xdd002000-0xdd0020ff irq 11 at device 8.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
rl0: Ethernet address: 00:40:f4:64:4d:d5
rl0: [MPSAFE]
fwohci0: <NEC uPD72873> mem 0xdd000000-0xdd000fff irq 10 at device 9.0 on pci0
fwohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdd000000
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:4c:01:07:00:30:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:00:4c:00:30:e1
fwe0: bpf attached
fwe0: Ethernet address: 02:00:4c:00:30:e1
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xdd001000-0xdd001fff irq 11 at device 12.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xec00
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 449 instructions downloaded
ahc0: Features 0x10005, Bugs 0x25, Flags 0x20481540
ahc0: [GIANT-LOCKED]
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: irq maps: 0x401 0x411 0x401 0x401
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0x401 0x409 0x401 0x401
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
unknown: status reg test failed fe
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
CTL0045: start dependent (0)
CTL0045: adding irq mask 0x20
CTL0045: adding dma mask 0x2
CTL0045: adding dma mask 0x20
CTL0045: adding io range 0x220-0x22f, size=0x10, align=0x1
CTL0045: adding io range 0x330-0x331, size=0x2, align=0x1
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0045: start dependent (1)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: start dependent (2)
CTL0045: adding irq mask 0x6a0
CTL0045: adding dma mask 0xb
CTL0045: adding dma mask 0xe0
CTL0045: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0045: adding io range 0x300-0x331, size=0x2, align=0x10
CTL0045: adding io range 0x388-0x397, size=0x4, align=0x4
CTL0045: end dependent
CTL7002: start dependent (0)
CTL7002: adding io range 0x200-0x207, size=0x8, align=0x1
CTL7002: start dependent (1)
CTL7002: adding io range 0x200-0x20f, size=0x8, align=0x8
CTL7002: end dependent
CTL0022: start dependent (0)
CTL0022: adding io range 0x620-0x623, size=0x4, align=0x1
CTL0022: start dependent (1)
CTL0022: adding io range 0x620-0x683, size=0x4, align=0x20
CTL0022: end dependent
PNP Identify complete
ahc_isa_probe 14: ioport 0xec00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff,0xd4000-0xdafff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <Audio> failed to probe at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq 1,5 on isa0
unknown: <Game> failed to probe at port 0x200-0x207 on isa0
unknown: <WaveTable> failed to probe at port 0x620-0x623 on isa0
uhub1: vendor 0x0557 product 0x7000, class 9/0, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
ukbd0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ums0: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
ums0: 3 buttons and Z dir.
uhub2: vendor 0x0451 product 0x2046, class 9/0, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 800033938 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
rr232x: no controller detected.
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on 82C596B chip
ad0: setting UDMA66 on 82C596B chip
ad0: 76351MB <SAMSUNG SP0802N TK200-04> at ata0-master UDMA66
ad0: 156368016 sectors [155127C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: VIA check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-slave: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
unknown: timeout waiting for read DRQ
unknown: timeout waiting for read DRQ
acd0: setting PIO4 on 82C596B chip
acd0: <GCR-8521B/1.02> CDROM drive at ata1 as slave
acd0: read 8937KB/s (8937KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked, lock protected
acd0: Medium: no/blank disc
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
ahc0: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:12. 0 SCBs aborted
ahc0: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahc0: Selection Timeout on A:5. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahc0: Selection Timeout on A:8. 0 SCBs aborted
ahc0: Selection Timeout on A:9. 0 SCBs aborted
ahc0: Selection Timeout on A:10. 0 SCBs aborted
ahc0: Selection Timeout on A:11. 0 SCBs aborted
ahc0: Selection Timeout on A:13. 0 SCBs aborted
ahc0: Selection Timeout on A:14. 0 SCBs aborted
ahc0: Selection Timeout on A:15. 0 SCBs aborted
(probe9:ahc0:0:2:0): Retrying Command
(ahc0:A:2:0): Sending WDTR 1
(ahc0:A:2:0): Received WDTR 1 filtered to 1
ahc0: target 2 using 16bit transfers
(ahc0:A:2:0): Sending SDTR period c, offset 8
(ahc0:A:2:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 2 synchronous at 20.0MHz, offset = 0x8
pass0 at ahc0 bus 0 target 2 lun 0
pass0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
pass0: Serial Number 369929932513
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
GEOM: new disk da0da0 at ahc0 bus 0 target 2 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0A0A> Fixed Direct Access SCSI-3 device
da0: Serial Number 369929932513
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
ATA PseudoRAID loaded
Trying to mount root from ufs:/dev/da0s3a
start_init: trying /sbin/init
##### OpenBSD 4.1 installation CD dmesg:
----------------------------------------
OpenBSD 4.1 (RAMDISK_CD) #248: Sat Mar 10 19:32:46 MST 2007
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 801 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 804810752 (785948K)
avail mem = 727834624 (710776K)
using 4278 buffers containing 40366080 bytes (39420K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 07/03/00, BIOS32 rev. 0 @ 0xfb240, SMBIOS rev. 2.2 @ 0xf0800 (43 entries)
bios0: VIA Technologies, Inc. VT82C692BX
apm0 at bios0: Power Management spec V1.2
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb6c8
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfddf0/144 (7 entries)
pcibios0: PCI Exclusive IRQs: 10 11 12
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xd000 0xd0000/0x4000! 0xd4000/0x7000
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0x44
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon VE QY" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C596A ISA" rev 0x23
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x10: ATA66, channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <SAMSUNG SP0802N>
wd0: 16-sector PIO, LBA48, 76351MB, 156368016 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <PIONEER, DVD-ROM DVD-119, 1.05> SCSI0 5/cdrom removable
atapiscsi1 at pciide0 channel 1 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <HL-DT-ST, CD-ROM GCR-8521B, 1.02> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
cd1(pciide0:1:1): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x11: irq 12
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"VIA VT82C596 Power" rev 0x30 at pci0 dev 7 function 3 not configured
rl0 at pci0 dev 8 function 0 "Realtek 8139" rev 0x10: irq 11, address 00:40:f4:64:4d:d5
rlphy0 at rl0 phy 0: RTL internal PHY
vendor "NEC", unknown product 0x00e7 (class serial bus subclass Firewire, rev 0x01) at pci0 dev 9 function 0 not configured
ahc0 at pci0 dev 12 function 0 "Adaptec AHA-2940U" rev 0x00: irq 11
scsibus2 at ahc0: 16 targets
sd0 at scsibus2 targ 2 lun 0: <QUANTUM, ATLAS IV 9 WLS, 0A0A> SCSI3 0/direct fixed
sd0: 8761MB, 13816 cyl, 4 head, 324 sec, 512 bytes/sec, 17942584 sec total
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
isapnp0 at isa0 port 0x279: read port 0x203
isapnp0: No current device for tag, card 1
"Creative AWE64 PnP, CTL0045, , Audio" at isapnp0 port 0x220/16,0x330/2,0x388/4 irq 5 drq 1,5 not configured
"Creative AWE64 PnP, CTL7002, PNPB02F, Game" at isapnp0 port 0x200/8 not configured
"Creative AWE64 PnP, CTL0022, , WaveTable" at isapnp0 port 0x620/4 not configured
biomask ffe5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
uhub1 at uhub0 port 1
uhub1: vendor 0x0557 product 0x7000, rev 1.10/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: CHICONY HP Basic USB Keyboard, rev 1.10/3.00, addr 3, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 4 configuration 1 interface 0
uhidev1: Genius NetScroll + Mini Traveler, rev 1.10/1.10, addr 4, iclass 3/1
uhid at uhidev1 not configured
uhub2 at uhub0 port 2
uhub2: vendor 0x0451 product 0x2046, rev 1.10/1.25, addr 5
uhub2: 4 ports with 4 removable, self powered
dkcsum: wd0 matches BIOS drive 0x80
ahc0: target 2 using 16bit transfers
ahc0: target 2 synchronous at 20.0MHz, offset = 0x8
dkcsum: sd0 matches BIOS drive 0x81
root on rd0a
rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
umass0 at uhub2 port 4 configuration 1 interface 0
umass0: vendor 0x0c76 product 0x0005, rev 1.10/1.00, addr 6
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets
sd1 at scsibus3 targ 1 lun 0: <Easy, Disk, 1.00> SCSI2 0/direct removable
sd1: 15MB, 15 cyl, 64 head, 32 sec, 512 bytes/sec, 31263 sec total
##### end of dmesg output files #####
Regards,
Keve Nagy
>How-To-Repeat:
I experienced this on two different hardware lately, but I am unable to describe a reliable way to reproduce it on your system. Try to test it on a configuration similar to the ones I described, like a PIII motherboard with two optical drives as secondary-master and slave.
>Fix:
>Release-Note:
>Audit-Trail:
>Unformatted:
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200707021114.l62BEvSq008426>