Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 6 May 2002 20:54:01 +1000
From:      "Scott Penno" <scott.penno@gennex.com.au>
To:        <freebsd-current@FreeBSD.ORG>, <freebsd-mobile@FreeBSD.ORG>
Subject:   Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
Message-ID:  <004e01c1f4ec$56f52490$0128a8c0@SCOTT>
References:  <000201c1f377$e7668d00$0128a8c0@SCOTT>

Next in thread | Previous in thread | Raw E-Mail | Index | Archive | Help
Just an update.  I've tried three different 32 bit cards and every time the
card was inserted the laptop locked up.  I recompiled the kernel without the
miibus and dc and then inserted the Xircom card the laptop would appear to
lock up, that is, everything that was running just stopped.  When the card
was re-inserted, everything would come back to life and a console message
would appear reporting 'pccbb0: Cardbus card activation failed'.  A similar
result was experienced with the other cards.  With that said, I'm still no
closer to identifying the cause of these problems.  Any ideas?

Scott.



----- Original Message -----
From: "Scott Penno" <scott.penno@gennex.com.au>
To: <freebsd-current@FreeBSD.ORG>; <freebsd-mobile@FreeBSD.ORG>
Sent: Sunday, May 05, 2002 12:27 AM
Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G [DRAFT]


> Hi there,
>
> I've been attempting to get my Xircom Realport CBEM56G working under
CURRENT
> for some time without success.  I grabbed the latest source on 03/05
12:00PM
> GMT and compiled without a problem.  I have a 3Com Etherlink III 3C589D
card
> which is a 16 bit card which I can insert and use without a problem.
> However when I try and insert my Xircom Realport CBEM56G, my laptop locks
> up.
> Under 4.X the cardbus bridge caused some intial problems getting
configured
> but once working, worked a treat and I suspect this is where the current
> problem is.  Without the kernel option PCI_ALLOW_UNSUPPORTED_IO_RANGE with
> NEWCARD, I'm unable to
> acheive any card functionality, when compiled with this option the 16 bit
> 3Com card works fine but the 32bit Xircom card causes a lockup.
Interesting
> to note also that under Windows XP and FreeBSD 4.X the bridge is detected
as
> an OZ6933, while under FreeBSD 5.X it's detected as an OZ6833.
> Not sure where to go from here so any assistance appreciated.  I've
included
> a dmesg from boot -v with the 3Com card, console messages when the Xircom
> card is inserted until the lockup occurs and finally the kernel
> configuration file.
>
> Regards,
>
> Scott.
>
>
>
> Copyright (c) 1992-2002 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>  The Regents of the University of California. All rights reserved.
> FreeBSD 5.0-CURRENT #2: Sat May  4 12:13:42 EST 2002
>     root@jupiter.gennex.com.au:/usr/obj/usr/src/sys/JUPITER
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc043b000.
> Preloaded elf module "/boot/kernel/acpi.ko" at 0xc043b0b4.
> Calibrating clock(s) ... TSC clock: 897239123 Hz, i8254 clock: 1193138 Hz
> CLK_USE_I8254_CALIBRATION not specified - using default frequency
> Timecounter "i8254"  frequency 1193182 Hz
> CLK_USE_TSC_CALIBRATION not specified - using old calibration method
> TSC initialization skipped: APM enabled.
> CPU: Pentium III/Pentium III Xeon/Celeron (897.28-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
>
>
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
> PAT,PSE36,MMX,FXSR,SSE>
> real memory  = 266797056 (260544K bytes)
> Physical memory chunk(s):
> 0x00001000 - 0x0009efff, 647168 bytes (158 pages)
> 0x00462000 - 0x0fe67fff, 262168576 bytes (64006 pages)
> avail memory = 254808064 (248836K bytes)
> bios32: Found BIOS32 Service Directory header at 0xc00f66b0
> bios32: Entry = 0xfd890 (c00fd890)  Rev = 0  Len = 1
> pcibios: PCI BIOS entry at 0xfd890+0x13a
> pnpbios: Found PnP BIOS data at 0xc00f6700
> pnpbios: Entry = f0000:a2a6  Rev = 1.0
> Other BIOS signatures found:
> null: <null device, zero device>
> random: <entropy source>
> mem: <memory & I/O>
> Pentium Pro MTRR support enabled
> VESA: information block
> 56 45 53 41 00 03 00 01 00 01 01 00 00 00 40 00
> 00 01 10 00 00 01 31 01 00 01 43 01 00 01 5d 01
> 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> VESA: 16 mode(s) found
> VESA: v3.0, 1024k memory, flags:0x1, mode table:0xc03895c0 (1000040)
> VESA: Intel815M(TM) Graphics Chip Accelerated VGA BIOS
> VESA: Intel Corporation i815M Graphics Controller Hardware Version 0.0
> pci_open(1): mode 1 addr port (0x0cf8) is 0x80001004
> pci_open(1a): mode1res=0x80000000 (0x80000000)
> pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086)
> Using $PIR table, 7 entries at 0xc00fdf50
> apm0: <APM BIOS> on motherboard
> apm0: found APM BIOS v1.2, connected at v1.2
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: Other PM system enabled.
> pcib0: <Intel 82815 (i815 GMCH) Host To Hub bridge> at pcibus 0 on
> motherboard
> pci0: physical bus=0
> found-> vendor=0x8086, dev=0x1130, revid=0x11
>  bus=0, slot=0, func=0
>  class=06-00-00, hdrtype=0x00, mfdev=0
>  map[10]: type 3, range 32, base f8000000, size 26, enabled
>  map[14]: type 1, range 32, base f4000000, size 19, enabled
> found-> vendor=0x8086, dev=0x1132, revid=0x11
>  bus=0, slot=2, func=0
>  class=03-00-00, hdrtype=0x00, mfdev=0
>  intpin=a, irq=10
>  powerspec 2  supports D0 D3  current D0
> found-> vendor=0x8086, dev=0x2448, revid=0x03
>  bus=0, slot=30, func=0
>  class=06-04-00, hdrtype=0x01, mfdev=0
> found-> vendor=0x8086, dev=0x244c, revid=0x03
>  bus=0, slot=31, func=0
>  class=06-01-00, hdrtype=0x00, mfdev=1
>  map[20]: type 4, range 32, base 00001800, size  4, enabled
> found-> vendor=0x8086, dev=0x244a, revid=0x03
>  bus=0, slot=31, func=1
>  class=01-01-80, hdrtype=0x00, mfdev=0
>  map[20]: type 4, range 32, base 00001820, size  5, enabled
> found-> vendor=0x8086, dev=0x2442, revid=0x03
>  bus=0, slot=31, func=2
>  class=0c-03-00, hdrtype=0x00, mfdev=0
>  intpin=d, irq=5
>  map[20]: type 4, range 32, base 00001810, size  4, enabled
> found-> vendor=0x8086, dev=0x2443, revid=0x03
>  bus=0, slot=31, func=3
>  class=0c-05-00, hdrtype=0x00, mfdev=0
>  intpin=b, irq=5
>  map[20]: type 4, range 32, base 00001880, size  5, enabled
> found-> vendor=0x8086, dev=0x2444, revid=0x03
>  bus=0, slot=31, func=4
>  class=0c-03-00, hdrtype=0x00, mfdev=0
>  intpin=c, irq=5
>  map[10]: type 4, range 32, base 00001c00, size  8, enabled
>  map[14]: type 4, range 32, base 00001840, size  6, enabled
> found-> vendor=0x8086, dev=0x2445, revid=0x03
>  bus=0, slot=31, func=5
>  class=04-01-00, hdrtype=0x00, mfdev=0
>  intpin=b, irq=5
> pci0: <PCI bus> on pcib0
> agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem
> 0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 10 at device 2.0 on pci0
> agp0: allocating GATT for aperture of size 64M
> pcib1: <PCI-PCI bridge> at device 30.0 on pci0
> pcib1:   secondary bus     1
> pcib1:   subordinate bus   1
> pcib1:   I/O decode        0xf000-0xfff
> pcib1:   memory decode     0xfff00000-0xfffff
> pcib1:   prefetched decode 0xfff00000-0xfffff
> pci1: physical bus=1
> found-> vendor=0x1217, dev=0x6933, revid=0x01
>  bus=1, slot=3, func=0
>  class=06-07-00, hdrtype=0x02, mfdev=1
>  intpin=a, irq=9
>  powerspec 2  supports D0 D1 D2 D3  current D0
> found-> vendor=0x1217, dev=0x6933, revid=0x01
>  bus=1, slot=3, func=1
>  class=06-07-00, hdrtype=0x02, mfdev=1
>  intpin=b, irq=9
>  powerspec 2  supports D0 D1 D2 D3  current D0
> pci1: <PCI bus> on pcib1
> pccbb0: <O2Mirco OZ6833 PCI-CardBus Bridge> irq 9 at device 3.0 on pci1
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> pcib1: device pccbb0 requested unsupported memory range
> 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> pcib1: device pccbb0 requested decoded memory range 0x84000000-0xffffffff
> cardbus0: <CardBus bus> on pccbb0
> pccard0: <16-bit PCCard bus> on pccbb0
> pccbb1: <O2Mirco OZ6833 PCI-CardBus Bridge> irq 9 at device 3.1 on pci1
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> pcib1: device pccbb1 requested unsupported memory range
> 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> pcib1: device pccbb1 requested decoded memory range 0x84000000-0xffffffff
> cardbus1: <CardBus bus> on pccbb1
> pccard1: <16-bit PCCard bus> on pccbb1
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device 31.1
on
> pci0
> ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1800
> ata0: mask=03 ostat0=50 ostat2=00
> ata0-master: ATAPI 00 00
> ata0-slave: ATAPI 00 00
> ata0: mask=03 stat0=50 stat1=00
> ata0-master: ATA 01 a5
> ata0: devices=01
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1808
> ata1: mask=03 ostat0=50 ostat2=00
> ata1-master: ATAPI 14 eb
> ata1-slave: ATAPI 00 00
> ata1: mask=03 stat0=00 stat1=00
> ata1: devices=04
> ata1: at 0x170 irq 15 on atapci0
> pci0: <serial bus, USB> at device 31.2 (no driver attached)
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> pci0: <serial bus, USB> at device 31.4 (no driver attached)
> pcm0: <Intel 82801BA (ICH2)> port 0x1840-0x187f,0x1c00-0x1cff irq 5 at
> device 31.5 on pci0
> pcm0: ac97 codec id 0x83847600 (SigmaTel STAC9700/9783/9784)
> pcm0: ac97 codec features 18 bit DAC, 18 bit ADC, 5 bit master volume,
> SigmaTel 3D Enhancement
> pcm0: sndbuf_setmap 71000, 4000; 0xd1dca000 -> 71000
> pcm0: sndbuf_setmap 8e000, 4000; 0xd1dd7000 -> 8e000
> pcm0: measured ac97 link rate at 29293 Hz
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> Trying Read_Port at 203
> Trying Read_Port at 243
> Trying Read_Port at 283
> Trying Read_Port at 2c3
> Trying Read_Port at 303
> Trying Read_Port at 343
> Trying Read_Port at 383
> Trying Read_Port at 3c3
> sc: sc0 already exists; skipping it
> vga: vga0 already exists; skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <Option ROMs> at iomem
0xd4000-0xd7fff,0xd0000-0xd3fff,0xc0000-0xcbfff
> on isa0
> adv0 failed to probe on isa0
> aha0 failed to probe on isa0
> aic0 failed to probe on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0047
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
> psm0: current command byte:0047
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse, device ID 3-00, 3 buttons
> psm0: config:00000000, flags:00000000, packet size:4
> psm0: syncmask:08, syncbits:08
> bt0 failed to probe on isa0
> cs0 failed to probe at port 0x300 on isa0
> ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
> fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port
> 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> fe0 failed to probe at port 0x300 on isa0
> ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
> le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
> lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
> pmtimer0 on isa0
> ppc0: parallel port found at 0x378
> ppc0: using extended I/O port range
> ppc0: ECP SPP ECP+EPP SPP
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> bpf: lp0 attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> sio0: irq maps: 0x1 0x11 0x1 0x1
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> sio1: irq maps: 0x1 0x1 0x1 0x1
> sio1: probe failed test(s): 0 1 2 4 6 7 9
> sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> sn0 failed to probe at port 0x300 irq 10 on isa0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> fb0: vga0, vga, type:VGA (5), flags:0x700ff
> fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> fb0: init mode:24, bios mode:3, current mode:24
> fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> VGA parameters upon power-up
> 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 06 40 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> VGA parameters in BIOS for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> EGA/VGA parameters to be used for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> vt0 failed to probe on isa0
> isa_probe_children: probing PnP devices
> BIOS Geometries:
>  0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
>  0 accounted for
> Device configuration finished.
> procfs registered
> Timecounters tick every 10.000 msec
> bpf: lo0 attached
> ad0: success setting UDMA5 on Intel chip
> Creating DISK ad0
> ar: FreeBSD check1 failed
> ad0: <HITACHI_DK23CA-20/00H1A0G1> ATA-5 disk at ata0-master
> ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
> ad0: 16 secs/int, 1 depth queue, UDMA100
> ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
> ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
> ata1-master: success setting PIO4 on generic chip
> acd0: <SAMSUNG CD-ROM SN-124/N001> CDROM drive at ata1 as master
> acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
> acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
> acd0: Writes:
> acd0: Audio: play, 255 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: CD-ROM 120mm audio disc
> Mounting root from ufs:/dev/ad0s2a
> ad0s1: type 0x6, start 63, end = 273104, size 273042 : OK
> ad0s2: type 0xa5, start 273105, end = 19663559, size 19390455 : OK
> ad0s3: type 0xf, start 19663560, end = 39054014, size 19390455
> ad0s3: C/H/S start 1023/0/1 (16434495) != start 19663560: invalid
> ad0s5: type 0x7, start 19663623, end = 39054014, size 19390392
> ad0s5: C/H/S start 1023/1/1 (16434558) != start 19663623: invalid
> start_init: trying /sbin/init
> Entropy harvesting:
>  interrupts
>  ethernet
>  point_to_point
> .
> swapon: adding /dev/ad0s2b as swap device
> swapon: adding /dev/ad0s2e as swap device
> Automatic boot in progress...
> /dev/ad0s2a: FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s2a: clean, 2846783 free (20743 frags, 353255 blocks, 0.5%
> fragmentation)
> Doing initial network setup:
>  host.conf
>  hostname
> .
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>  inet 127.0.0.1 netmask 0xff000000
> route:
> writing to routing socket
> :
> Network is unreachable
> add net default: gateway 192.168.40.254: Network is unreachable
> Additional routing options:
> .
> Routing daemons:
> .
> Additional daemons:
>  syslogd
> May  4 12:59:53 jupiter syslogd: kernel boot file is /boot/kernel/kernel
> .
> Doing additional network setup:
> .
> Starting final network daemons:
> .
> ELF ldconfig path: /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
> a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
/usr/X11R6/lib/aout
> Starting standard daemons:
>  cron
>  sshd
>  sendmail-submit
>  sendmail-clientmqueue
> .
> Initial rc.i386 initialization:
> .
> Configuring syscons:
>  blanktime
> .
> Additional ABI support:
> .
> Local package initialization:
> .
> Additional TCP options:
> .
> Starting background filesystem checks
>
> Sat May  4 12:59:55 EST 2002
> May  4 13:00:03 jupiter login: ROOT LOGIN (root) ON ttyv1
> link_elf: symbol gd_curproc undefined
> link_elf: symbol gd_curproc undefined
> link_elf: symbol gd_curproc undefined
> link_elf: symbol gd_curproc undefined
> link_elf: symbol gd_curproc undefined
> fd0: autoselected 1440 KB medium
> WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> fd0: autoselected 1440 KB medium
> WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> pcib1: device pccard0 requested unsupported memory range
> 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> pcib1: device pccard0 requested decoded memory range 0x84000000-0xffffffff
> pccard0: CIS version PCCARD 2.0 or 2.1
> pccard0: CIS info: 3Com Corporation, 3C589D, TP/BNC LAN Card Ver. 2a,
000002
> pccard0: Manufacturer code 0x101, product 0x589
> pccard0: function 0: network adapter, ccr addr 10000 mask 3
> pccard0: function 0, config table entry 1: I/O card; irq mask ffff; iomask
> 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
> pccard0: function 0, config table entry 3: I/O card; irq mask ffff; iomask
> 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
> pcib1: device pccard0 requested decoded I/O range 0x100-0xffffffff
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> pcib1: device pccard0 requested unsupported memory range
> 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> pcib1: device pccard0 requested decoded memory range 0x84000000-0xffffffff
> ep0: <3Com 3c589 10Mbps Ethernet> at port 0x100-0x10f irq 9 function 0
> config 1 on pccard0
> pcib1: device ep0 requested decoded I/O range 0x100-0x10f
> pcib1: device pccard0 requested decoded I/O range 0x100-0x10f
> pcib1: device ep0 requested decoded I/O range 0x100-0x10f
> ep0: Ethernet address 00:60:97:89:94:37
> bpf: ep0 attached
> May  4 13:35:25 jupiter login: ROOT LOGIN (root) ON ttyv2
>
>
>
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> Product version: 5.0
> Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03
|
> Manufacturer ID: 0501030181
> Functions: Network Adaptor, Multi-Functioned
> Function Extension: 04060010a4d1c890
> Function Extension: 0102
> Function Extension: 0280969800
> Function Extension: 0200e1f505
> Function Extension: 0301
> Function Extension: 0303
> Function Extension: 0501
> cardbus0: Invalid BAR number: 27(06)
> CIS reading done
> start (84000000) < sc->membase (fff00000)
> end (ffffffff) > sc->memlimit (fffff)
> pcib1: device cardbus0 requested unsupported memory range
> 0x84000000-0xffffffff
> (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> pcib1: device cardbus0 requested decoded memory range
0x84000000-0xffffffff
> end (0x840217f) > sc->memlimit (fffff)
> pcib1: device cardbus0 requested unsupported memory range
> 0x84002000-0x8400217f
> (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> pcib1: device cardbus0 requested decoded memory range
0x84002000-0x8400217f
> end (8400217f) > sc->memlimit (fffff)
> pcib1: device cardbus0 requested unsupported memory range
> 0x84002000-0x8400217f
> (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> pcib1: device cardbus0 requested decoded memory range
0x84002000-0x8400217f
> pcib1: device cardbus0 requested decoded I/O range 0x1000-0xffffffff
> pcib1: device cardbus0 requested decoded I/O range 0x1000-0x107f
> dc0: <Xircom X3201 10/100BaseTX> port 0x1000-0x107f mem
> 0x84002000-0x840020ff,0x84002100-0x8400217f irq 9 at device 0.0 on
cardbus0
> pcib1: device dc0 requested decoded I/O range 0x1000-0x107f
> <... hardlock occurs here ...>
>
>
>
> #
> # NEWCARD -- efforts at porting newconfig pccard/cardbus code to newbus
> #
>
> machine  i386
> cpu  I686_CPU
> ident  JUPITER
> maxusers 0
>
> makeoptions DEBUG=-g  #Build kernel with gdb(1) debug symbols
>
> options  INET   #InterNETworking
> options  FFS   #Berkeley Fast Filesystem
> options  SOFTUPDATES  #Enable FFS soft updates support
> options  UFS_DIRHASH  #Improve performance on big directories
> options  NFSCLIENT  #Network Filesystem Client
> options  MSDOSFS   #MSDOS Filesystem
> options  CD9660   #ISO 9660 Filesystem
> options  PROCFS   #Process filesystem (requires PSEUDOFS)
> options  PSEUDOFS  #Pseudo-filesystem framework
> options  COMPAT_43  #Compatible with BSD 4.3 [KEEP THIS!]
> options  KTRACE   #ktrace(1) support
> options  SYSVSHM   #SYSV-style shared memory
> options  SYSVMSG   #SYSV-style message queues
> options  SYSVSEM   #SYSV-style semaphores
> options  P1003_1B  #Posix P1003_1B real-time extensions
> options  _KPOSIX_PRIORITY_SCHEDULING
> options  KBD_INSTALL_CDEV # install a CDEV entry in /dev
>
> # Debugging for use in -current
> options  DDB   #Enable the kernel debugger
> options  INVARIANTS  #Enable calls of extra sanity checking
> options  INVARIANT_SUPPORT #Extra sanity checks of internal structures,
> required by INVARIANTS
> options  WITNESS   #Enable mutex checks to detects deadlocks and cycles
> options  WITNESS_SKIPSPIN #Don't run witness on spinlocks for speed
>
> device  isa
> device  pci
> #options  PCI_ENABLE_IO_MODES # Enable pci resources left off by a "lazy
> BIOS"
> options  PCI_ALLOW_UNSUPPORTED_IO_RANGE
>
> # AGP GART support
> device  agp
> options  VESA
>
> # Floppy drives
> device  fdc
>
> # ATA and ATAPI devices
> device  ata
> device  atadisk   # ATA disk drives
> device  atapicd   # ATAPI CDROM drives
>
> # atkbdc0 controls both the keyboard and the PS/2 mouse
> device  atkbdc 1 # At keyboard controller
> device  atkbd  # at keyboard
> device  psm  # psm mouse
>
> device  vga  # VGA screen
>
> # splash screen/screen saver
> device  splash
>
> # syscons is the default console driver, resembling an SCO console
> device  sc 1
>
> # Floating point support - do not disable.
> device  npx
>
> # Power management support (see NOTES for more options)
> device  apm
> # Add suspend/resume support for the i8254.
> device  pmtimer
>
> # Pcmcia and cardbus bridge support
> device  pccbb   # cardbus (yenta) bridge
> device  pccard
> device  cardbus
> #device  card
> #device  pcic
>
> # Serial (COM) ports
> device  sio  # 8250, 16[45]50 based serial ports
>
> # Parallel port
> device  ppc
> device  ppbus  # Parallel port bus (required)
> device  lpt  # Printer
> device  plip  # TCP/IP over parallel
>
> # PCI Ethernet NICs that use the common MII bus controller code.
> # NOTE: Be sure to keep the 'device miibus' line in order to use these
NICs!
> device  miibus  # MII bus support
> device  dc  # DEC/Intel 21143 and various workalikes
>
> # ISA Ethernet NICs.  pccard nics included.
> device  ep  # Etherlink III based cards
>
> # Wireless NIC cards
> device  wi  # WaveLAN/IEEE 802.11 wireless NICs.
>
> # Pseudo devices - the number indicates how many units to allocate.
> device  random  # Entropy device
> device  loop  # Network loopback
> device  ether  # Ethernet support
> device  tun  # Packet tunnel.
> device  pty  # Pseudo-ttys (telnet etc)
> device  md  # Memory "disks"
> device  gif  # IPv6 and IPv4 tunneling
>
> # The `bpf' device enables the Berkeley Packet Filter.
> # Be aware of the administrative consequences of enabling this!
> device  bpf  # Berkeley packet filter
>
> device  pcm
>
>
>
>
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-mobile" in the body of the message
>
>



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?004e01c1f4ec$56f52490$0128a8c0>