Date: Wed, 25 Dec 2002 20:08:31 +0900 From: "Patrick Lathem" <trashcan@hotmail.com> To: mobile@freebsd.org Subject: 4.7 -> 5.0 Pccard problems (more info) Message-ID: <BAY1-F1633JCYaHXPDl0001ce01@hotmail.com>
next in thread | raw e-mail | index | archive | help
Hi. My PCMCIA slot stopped working after I upgraded from 4.7 to 5.0 RC1
(and is still not working on 5.0 cvsupped a few hours ago). When I try to
run pccardd manually as root I get this:
pccardd[541]: fatal error: no PC-CARD slots
I emailed the list earlier, but I failed to mention that error.
I'm assuming it is no longer recognizing my Pcmcia device (not the card).
The Cardbus controller is a Texas Instruments PCI1410.
pciconf reports:
cbb0@pci2:6:0: class=0x060700 card=0xb1030e11 chip=0xac50104c rev=0x01
hdr=0x02
vendor = 'Texas Instruments (TI)'
device = 'PCI1410 PC card cardBus Controller'
class = bridge
subclass = PCI-CardBus
Dmesg (sorry I wasn't 100% which sections were relevant):
real memory = 536215552 (511 MB)
avail memory = 513986560 (490 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI-0625: *** Info: GPE Block1 defined as GPE16 to GPE31
Using $PIR table, 11 entries at 0xc00fdf10
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast" frequency 3579545 Hz
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
unknown: memory range not supported
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82830 host to AGP bridge> mem 0xe0000000-0xefffffff at device
0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1860-0x187f
irq 9 at dev
ice 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1880-0x189f
irq 11 at de
vice 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1800-0x181f
irq 9 at dev
ice 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pci2: <simple comms> at device 4.0 (no driver attached)
pci2: <serial bus, FireWire> at device 5.0 (no driver attached)
cbb0: <TI1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fxp0: <Intel Pro/100 Ethernet> port 0x3040-0x307f mem 0xd0215000-0xd0215fff
irq 10 at
device 8.0 on pci2
fxp0: Ethernet address 00:02:a5:6c:89:88
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port
0x1820-0x182f,0x374-0x377,0x170-0x177,0x3
f4-0x3f7,0x1f0-0x1f7 mem 0xd0000000-0xd00003ff at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel 82801CA (ICH3)> port 0x18c0-0x18ff,0x1c00-0x1cff irq 5 at
device 31.5 on
pci0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 i
rq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
orm0: <Option ROMs> at iomem
0xe5000-0xe5fff,0xe0000-0xe3fff,0xce000-0xcefff,0xc0000-0
xcdfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
cbb0: Unsupported card type detected
ad0: 28615MB <TOSHIBA MK3017GAP> [58140/16/63] at ata0-master UDMA100
acd0: DVD-ROM <LG DVD-ROM DRN-8080B> at ata0-slave PIO4
acd1: CD-RW <UJDA330> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s2a
ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
ACPI-1287: *** Error: Method execution failed, AE_ERROR
ACPI-1287: *** Error: Method execution failed, AE_ERROR
ACPI-1287: *** Error: Method execution failed, AE_ERROR
ACPI-1287: *** Error: Method execution failed, AE_ERROR
Any advice would be appreciated. Thanks.
Pat Lathem
(Please ignore the hotmail spam below- I cannot reach freebsd.org from my
ISP's mail server for some reason).
_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 3 months FREE*.
http://join.msn.com/?page=features/junkmail&xAPID=42&PS=47575&PI=7324&DI=7474&SU=
http://www.hotmail.msn.com/cgi-bin/getmsg&HL=1216hotmailtaglines_stopmorespam_3mf
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BAY1-F1633JCYaHXPDl0001ce01>