Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 1 Sep 2003 16:28:58 -0400
From:      Mik Firestone <mik@racerx.homedns.org>
To:        freebsd-current@freebsd.org
Subject:   xl0: reset didn't complete
Message-ID:  <20030901202858.GA15579@racerx.homedns.org>

next in thread | raw e-mail | index | archive | help
I am using -CURRENT cvsup'd August 29 and having some problems with a
3com 3c575B PC Card.  I am running on a Dell Latitude C600 and -CURRENT
has, for the most part, worked perfectly for me.

The problem is that the 3Com card is no longer getting activated.  The
system sees when the card is plugged in and attempts to initialize it,
but the initialization always fail with an "xl0 reset didn't complete".
I did a quick couple of google searches and grep'd my email folders and
didn't turn up anything helpful to me.  I will also point out that,
unlike Soeren's problems on August 13, wi0 is working just fine for me.

Attached are the results of a boot -v, as well as the results from me
setting hw.cardbus.debug and hw.pccard.debug to 1.  For grins, I have
also included my kernel configuration.  Sorry for the long email.

Any help would be greatly appreciated.

Mik

boot -v:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Fri Aug 29 23:35:14 EDT 2003
    root@bullet:/usr/obj/usr/src/sys/BULLET
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04af000.
Preloaded elf module "/boot/kernel/snd_ess.ko" at 0xc04af1cc.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc04af278.
Preloaded elf module "/boot/kernel/snd_sbc.ko" at 0xc04af324.
Preloaded acpi_dsdt "/boot/acpi_dsdt.aml" at 0xc04af3d0.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04af418.
Calibrating clock(s) ... i8254 clock: 1193123 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 751706469 Hz
CPU: Intel Pentium III (751.71-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 268283904 (255 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x00000000004d6000 - 0x000000000fb34fff, 258338816 bytes (63071 pages)
avail memory = 255438848 (243 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xc12e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
random: <entropy source>
ACPI: DSDT was overridden.
    ACPI-0375: *** Info: Table [DSDT] replaced by host OS
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   CPi R  > on motherboard
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fbd70
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    7    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    1    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    1    0    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0    3    A   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0    3    B   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0    8    A   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0   16    A   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   16    B   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    8    0    A   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    8    1    A   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   13    A   0x62  11
embedded    0   17    A   0x62  11
embedded    0   17    B   0x62  11
embedded    0   17    C   0x62  11
embedded    0   17    D   0x62  11
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.0
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.1
\\_SB_.PCI0.LNKC irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.8.0
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.16.0
\\_SB_.PCI0.LNKC irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.16.1
---- before setting priority for links ------------
\\_SB_.PCI0.LNKC:
	interrupts:	     3     4     5     6     7     9    10    11    12    14    15
	penalty:	  1330  1330   630  1330  1330   330   330   930  1330 10330 10330
	references:	3
	priority:	0
---- before fixup boot-disabled links -------------
\\_SB_.PCI0.LNKC:
	interrupts:	     3     4     5     6     7     9    10    11    12    14    15
	penalty:	  1330  1330   630  1330  1330   330   330   930  1330 10330 10330
	references:	3
	priority:	8053
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq  10: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.0
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.1
\\_SB_.PCI0.LNKC irq  10: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKB irq   5: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.8.0
\\_SB_.PCI0.LNKD irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.16.0
\\_SB_.PCI0.LNKC irq  10: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.16.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base f4000000, size 26, enabled
found->	vendor=0x8086, dev=0x7190, revid=0x03
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2210, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x7191, revid=0x03
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x011f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x8c (35000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x104c, dev=0xac51, revid=0x00
	bus=0, slot=3, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 1  supports D0 D1 D2 D3  current D0
found->	vendor=0x104c, dev=0xac51, revid=0x00
	bus=0, slot=3, func=1
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 1  supports D0 D1 D2 D3  current D0
found->	vendor=0x8086, dev=0x7110, revid=0x02
	bus=0, slot=7, func=0
	class=06-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 00000860, size  4, enabled
found->	vendor=0x8086, dev=0x7111, revid=0x01
	bus=0, slot=7, func=1
	class=01-01-80, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000dce0, size  5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 11
found->	vendor=0x8086, dev=0x7112, revid=0x01
	bus=0, slot=7, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=11
	map[90]: type 4, range 32, base 00000840, size  4, enabled
found->	vendor=0x8086, dev=0x7113, revid=0x03
	bus=0, slot=7, func=3
	class=06-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 4, range 32, base 0000d800, size  8, enabled
	map[14]: type 1, range 32, base f3ffe000, size 13, enabled
pcib0: matched entry for 0.8.INTA (source \\_SB_.PCI0.LNKB)
pcib0: slot 8 INTA is routed to irq 5
found->	vendor=0x125d, dev=0x1998, revid=0x10
	bus=0, slot=8, func=0
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
	intpin=a, irq=5
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base f3ffdc00, size  8, enabled
	map[14]: type 4, range 32, base 0000dcd8, size  3, enabled
	map[18]: type 4, range 32, base 0000d400, size  8, enabled
pcib0: matched entry for 0.16.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 16 INTA is routed to irq 11
found->	vendor=0x11c1, dev=0x0448, revid=0x01
	bus=0, slot=16, func=0
	class=07-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0xfc (63000 ns), maxlat=0x0e (3500 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D2 D3  current D0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf4000000-0xf7ffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xe000-0xefff
pcib1:   memory decode     0xfd000000-0xfeffffff
pcib1:   prefetched decode 0xf8000000-0xfbffffff
---- initial configuration ------------------------
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq  11: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
	map[10]: type 3, range 32, base f8000000, size 26, enabled
	map[14]: type 4, range 32, base 0000ec00, size  8, enabled
	map[18]: type 1, range 32, base fdffc000, size 14, enabled
pcib1: matched entry for 1.0.INTA (source \\_SB_.PCI0.LNKA)
pcib1: slot 0 INTA is routed to irq 11
found->	vendor=0x1002, dev=0x4c46, revid=0x02
	bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1420 PCI-CardBus Bridge> at device 3.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.3.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 3 INTA is routed to irq 11
cbb0: PCI Configuration space:
  0x00: 0xac51104c 0x02100007 0x06070000 0x00822008 
  0x10: 0x88000000 0x220000a0 0x20040400 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 
  0x40: 0x00b11028 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x2024f025 0x00000000 0x00000000 0x01261222 
  0x90: 0x6064a6c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe110001 0x00c00000 0x0000081b 0x00000007 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
cbb1: <TI1420 PCI-CardBus Bridge> at device 3.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: matched entry for 0.3.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 3 INTA is routed to irq 11
cbb1: PCI Configuration space:
  0x00: 0xac51104c 0x02100007 0x06070000 0x00822008 
  0x10: 0x88001000 0x220000a0 0x20050500 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 
  0x40: 0x00b11028 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x2024f025 0x00000000 0x00000000 0x01261222 
  0x90: 0x6064a6c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe110001 0x00c00000 0x0000081b 0x00000007 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x860-0x86f at device 7.1 on pci0
ata0: pre reset mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: after reset mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: pre reset mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 00 00
ata1: after reset mask=03 stat0=00 stat1=00
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xdce0-0xdcff irq 11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
pci0: <simple comms> at device 16.0 (no driver attached)
unknown: not probed (disabled)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x101 0x111 0x101 0x101
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x141 0x141 0x141 0x141
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 c3 
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f 
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 c3 
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f 
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 751706469 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
cardbus0: Resource not specified in CIS: id=14, size=80
cardbus0: Resource not specified in CIS: id=18, size=80
found->	vendor=0x10b7, dev=0x5157, revid=0x01
	bus=4, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0xa8 (5040 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns)
	intpin=a, irq=11
	powerspec 1  supports D0 D1 D2 D3  current D0
xl0: <3Com 3c575B Fast Etherlink XL> port 0x1000-0x107f mem 0x88002000-0x8800207f,0x88002080-0x880020ff irq 11 at device 0.0 on cardbus0
xl0: using memory mapped I/O
xl0: reset didn't complete
xl0: command never completed!
xl0: command never completed!
xl0: eeprom failed to come ready
xl0: failed to read station address
device_probe_and_attach: xl0 attach returned 6
cbb0: CardBus card activation failed
pccard1: CIS version PC Card Standard 5.0
pccard1: CIS info: NETGEAR MA401RA Wireless PC, Card, ISL37300P, Eval-RevA
pccard1: Manufacturer code 0xb, product 0x7300
pccard1: function 0: network adapter, ccr addr 3e0 mask 1
pccard1: function 0, config table entry 1: I/O card; irq mask ffff; iomask 6, iospace 0-3f; io16 irqpulse irqlevel
wi0: <NETGEAR MA401RA Wireless PC Card> at port 0x100-0x13f irq 11 function 0 config 1 on pccard1
wi0: 802.11 address: 00:09:5b:4b:c9:30
wi0: using RF:PRISM2.5 MAC:ISL3873
wi0: Intersil Firmware: Primary (1.0.7), Station (1.3.6)
wi0: bpf attached
wi0: bpf attached
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ata0-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin
acpi_cmbat1: battery initialization start
ad0: setting UDMA33 on Intel PIIX4 chip
ad0: <FUJITSU MHK2120AT/D834> ATA-5 disk at ata0-master
ad0: 11513MB (23579136 sectors), 23392 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
GEOM: new disk ad0
ata1-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
acd0: setting PIO4 on Intel PIIX4 chip
acd0: <SONY CD-RW CRX700E/1.4r> CDRW drive at ata1 as master
acd0: read 4134KB/s (4134KB/s) write 1377KB/s (1377KB/s), 8192KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes: CDR, CDRW, test write
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/15/63 s:63 l:23579073
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 12072485376 end 12072517631
GEOM: Configure ad0s1a, start 0 length 2147483648 end 2147483647
GEOM: Configure ad0s1b, start 2147483648 length 536870912 end 2684354559
GEOM: Configure ad0s1c, start 0 length 12072485376 end 12072485375
GEOM: Configure ad0s1d, start 2684354560 length 536870912 end 3221225471
GEOM: Configure ad0s1e, start 3221225472 length 8851259904 end 12072485375
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
pass0 at ata1 bus 0 target 0 lun 0
pass0: <SONY CD-RW  CRX700E 1.4r> Removable CD-ROM SCSI-0 device 
pass0: Serial Number [
pass0: 16.000MB/s transfers
cd0 at ata1 bus 0 target 0 lun 0
cd0: <SONY CD-RW  CRX700E 1.4r> Removable CD-ROM SCSI-0 device 
cd0: Serial Number [
cd0: 16.000MB/s transfers
cd0: cd present [1633955841 x 6247245 byte records]
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
splash: image decoder found: daemon_saver
Linux ELF exec handler installed
acpi_cmbat1: battery initialization failed, giving up

Results from setting the hw.*.debug:

Sep  1 15:50:57 bullet kernel: CBB EVENT 0x6
Sep  1 15:50:57 bullet kernel: Waking up thread
Sep  1 15:50:57 bullet kernel: CBB EVENT 0x2
Sep  1 15:50:57 bullet kernel: Waking up thread
Sep  1 15:50:57 bullet kernel: CBB EVENT 0x2
Sep  1 15:50:57 bullet kernel: Waking up thread
Sep  1 15:50:58 bullet kernel: Status is 0x30000186
Sep  1 15:51:01 bullet kernel: CBB EVENT 0x2
Sep  1 15:51:01 bullet kernel: Waking up thread
Sep  1 15:51:01 bullet kernel: CBB EVENT 0x2
Sep  1 15:51:01 bullet kernel: Waking up thread
Sep  1 15:51:01 bullet kernel: CBB EVENT 0x2
Sep  1 15:51:01 bullet kernel: Waking up thread
Sep  1 15:51:02 bullet kernel: CBB EVENT 0x2
Sep  1 15:51:02 bullet kernel: Waking up thread
Sep  1 15:51:03 bullet kernel: Status is 0x30000186
Sep  1 15:51:03 bullet kernel: CBB EVENT 0x4
Sep  1 15:51:03 bullet kernel: Waking up thread
Sep  1 15:51:03 bullet kernel: CBB EVENT 0x4
Sep  1 15:51:03 bullet kernel: Waking up thread
Sep  1 15:51:03 bullet kernel: CBB EVENT 0x4
Sep  1 15:51:03 bullet kernel: Waking up thread
Sep  1 15:51:03 bullet kernel: CBB EVENT 0x4
Sep  1 15:51:03 bullet kernel: Waking up thread
Sep  1 15:51:03 bullet kernel: CBB EVENT 0x6
Sep  1 15:51:03 bullet kernel: Waking up thread
Sep  1 15:51:05 bullet kernel: Status is 0x30000920
Sep  1 15:51:05 bullet kernel: cbb0: card inserted: event=0x00000000, state=30000920
Sep  1 15:51:05 bullet kernel: cbb0: cbb_power: 3V
Sep  1 15:51:05 bullet kernel: cardbus0: Resource not specified in CIS: id=14, size=80
Sep  1 15:51:05 bullet kernel: cardbus0: Resource not specified in CIS: id=18, size=80
Sep  1 15:51:05 bullet kernel: xl0: <3Com 3c575B Fast Etherlink XL> port 0x1000-0x107f mem 0x88003000-0x8800307f,0x88003080-0x880030ff irq 11 at device 0.0 on cardbus0
Sep  1 15:51:06 bullet kernel: xl0: reset didn't complete
Sep  1 15:51:06 bullet kernel: xl0: command never completed!
Sep  1 15:51:06 bullet kernel: xl0: command never completed!
Sep  1 15:51:06 bullet kernel: xl0: eeprom failed to come ready
Sep  1 15:51:06 bullet kernel: xl0: failed to read station address
Sep  1 15:51:06 bullet kernel: device_probe_and_attach: xl0 attach returned 6
Sep  1 15:51:06 bullet kernel: cbb0: cbb_power: 0V
Sep  1 15:51:06 bullet kernel: cbb0: CardBus card activation failed

And, just for giggles, my kernel config:

#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#    http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files. 
# If you are in doubt as to the purpose or necessity of a line, check first 
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.384.2.2 2003/05/31 15:18:41 scottl Exp $

machine		i386
cpu		I686_CPU
ident		BULLET

#To statically compile in device wiring instead of /boot/device.hints
#hints		"GENERIC.hints"		#Default places to look for devices.

#makeoptions	DEBUG=-g		#Build kernel with gdb(1) debug symbols

options 	SCHED_4BSD		#4BSD scheduler
options 	INET			#InterNETworking
options 	FFS			#Berkeley Fast Filesystem
options 	SOFTUPDATES		#Enable FFS soft updates support
options 	UFS_ACL			#Support for access control lists
options 	UFS_DIRHASH		#Improve performance on big directories
options 	MD_ROOT			#MD is a potential root device
options 	NFSSERVER		#Network Filesystem Server
options 	MSDOSFS			#MSDOS Filesystem
options 	CD9660			#ISO 9660 Filesystem
options 	PROCFS			#Process filesystem (requires PSEUDOFS)
options 	PSEUDOFS		#Pseudo-filesystem framework
options 	COMPAT_43		#Compatible with BSD 4.3 [KEEP THIS!]
options 	COMPAT_FREEBSD4		#Compatible with FreeBSD4
options 	SCSI_DELAY=5000		#Delay (in ms) before probing SCSI
options 	KTRACE			#ktrace(1) support
options 	SYSVSHM			#SYSV-style shared memory
options 	SYSVMSG			#SYSV-style message queues
options 	SYSVSEM			#SYSV-style semaphores
options 	_KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions
options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev
options 	AHC_REG_PRETTY_PRINT	# Print register bitfields in debug
					# output.  Adds ~128k to driver.
options 	AHD_REG_PRETTY_PRINT	# Print register bitfields in debug
					# output.  Adds ~215k to driver.

# Debugging for use in -current
#options 	DDB			#Enable the kernel debugger
#options 	INVARIANTS		#Enable calls of extra sanity checking
options 	INVARIANT_SUPPORT	#Extra sanity checks of internal structures, required by INVARIANTS
#options 	WITNESS			#Enable checks to detect deadlocks and cycles
#options 	WITNESS_SKIPSPIN	#Don't run witness on spinlocks for speed

# To make an SMP kernel, the next two are needed
#options 	SMP			# Symmetric MultiProcessor Kernel
#options 	APIC_IO			# Symmetric (APIC) I/O

device		isa
device		eisa
device		pci

# Floppy drives
device		fdc

# ATA and ATAPI devices
device		ata
device		atadisk			# ATA disk drives
device		atapicd			# ATAPI CDROM drives
device 		atapicam
options 	ATA_STATIC_ID		#Static device numbering

# SCSI peripherals
device		scbus		# SCSI bus (required)
device		cd		# CD
device		pass		# Passthrough device (direct SCSI access)
device		ses		# SCSI Environmental Services (and SAF-TE)

# atkbdc0 controls both the keyboard and the PS/2 mouse
device		atkbdc		# AT keyboard controller
device		atkbd		# AT keyboard
device		psm		# PS/2 mouse

device		vga		# VGA video card driver

device		splash		# Splash screen and screen saver support

# syscons is the default console driver, resembling an SCO console
device		sc

# Enable this for the pcvt (VT220 compatible) console driver
#device		vt
options 	XSERVER			# support for X server on a vt console
#options 	FAT_CURSOR		# start with block cursor

device		agp		# support several AGP chipsets

# Floating point support - do not disable.
device		npx

# Power management support (see NOTES for more options)
#device		apm
# Add suspend/resume support for the i8254.
device		pmtimer

# PCCARD (PCMCIA) support
# Pcmcia and cardbus bridge support
device		cbb			# cardbus (yenta) bridge
#device		pcic			# ExCA ISA and PCI bridges
device		pccard			# PC Card (16-bit) bus
device		cardbus			# CardBus (32-bit) bus

# Serial (COM) ports
device		sio		# 8250, 16[45]50 based serial ports

# Parallel port
device		ppc
device		ppbus		# Parallel port bus (required)
device		lpt		# Printer


# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device		miibus		# MII bus support
device		xl		# 3Com 3c90x (``Boomerang'', ``Cyclone'')


# Wireless NIC cards
device		wlan		# 802.11 support
device		wi		# WaveLAN/Intersil/Symbol 802.11 wireless NICs.

# Pseudo devices - the number indicates how many units to allocate.
device		random		# Entropy device
device		loop		# Network loopback
device		ether		# Ethernet support
device		tun		# Packet tunnel.
device		pty		# Pseudo-ttys (telnet etc)

# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device		bpf		# Berkeley packet filter

# USB support
device		uhci		# UHCI PCI->USB interface
device		ohci		# OHCI PCI->USB interface
device		usb		# USB Bus (required)
device		ugen		# Generic
device		uhid		# "Human Interface Devices"
device		ukbd		# Keyboard
device		ums		# Mouse



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030901202858.GA15579>