Date: Fri, 1 Dec 2000 16:13:36 -0500 From: Barry Lustig <barry@lustig.com> To: stable@freebsd.org, mobile@freebsd.org Subject: Boot problem with 4.2-STABLE on VAIO z505-LE Message-ID: <20001201211336.8019.qmail@devious.lustig.com>
next in thread | raw e-mail | index | archive | help
When I add "device umass" to my configuration I get the following failure on
boot. I've added the configuration file at the end of this message. Any
ideas?
barry
ok boot -v
SMAP type=01 base=00000000 00000000 len=00000000 0009f800
SMAP type=02 base=00000000 0009f800 len=00000000 00000800
SMAP type=02 base=00000000 000e8400 len=00000000 00017c00
SMAP type=01 base=00000000 00100000 len=00000000 0bef0000
SMAP type=03 base=00000000 0bff0000 len=00000000 0000f800
SMAP type=04 base=00000000 0bfff800 len=00000000 00000800
SMAP type=02 base=00000000 fff80000 len=00000000 00080000
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-STABLE #7: Fri Dec 1 14:08:28 EST 2000
barry@vaio.lustig.com:/usr/src/sys/compile/VAIO
Calibrating clock(s) ... TSC clock: 645193534 Hz, i8254 clock: 1193167 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon/Celeron (645.21-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 201261056 (196544K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00408000 - 0x0bfe7fff, 197001216 bytes (48096 pages)
avail memory = 191856640 (187360K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6c10
bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x11e
pnpbios: Found PnP BIOS data at 0xc00f6c40
pnpbios: Entry = f0000:b431 Rev = 1.0
pnpbios: Event flag at 400
Other BIOS signatures found:
ACPI: 000f6bb0
Preloaded elf kernel "kernel" at 0xc03e2000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 40000000, size 24
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000fc90, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[20]: type 1, range 32, base 0000fca0, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x03
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00001040, size 4
found-> vendor=0x104d, dev=0x8039, revid=0x02
class=0c-00-10, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base fedf7000, size 11
map[14]: type 1, range 32, base fedf7c00, size 9
found-> vendor=0x1073, dev=0x0010, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base fedf8000, size 15
map[14]: type 1, range 32, base 0000fcc0, size 6
map[18]: type 3, range 32, base 0000fc8c, size 2
found-> vendor=0x14f1, dev=0x2443, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base fede0000, size 16
map[14]: type 3, range 32, base 0000fc38, size 3
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base fedf6000, size 12
map[14]: type 1, range 32, base 0000fc40, size 6
map[18]: type 1, range 32, base fec00000, size 20
found-> vendor=0x1180, dev=0x0475, revid=0x80
class=06-07-00, hdrtype=0x02, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4c4d, revid=0x64
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 32, base 0000e800, size 8
map[18]: type 1, range 32, base febff000, size 12
pci1: <PCI bus> on pcib1
pci1: <ATI Mobility-1 graphics accelerator> (vendor=0x1002, dev=0x4c4d) at
0.0 irq 9
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfc90
ata0: mask=03 status0=50 status1=00
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI probe a=00 b=00
ata0-slave: ATAPI probe a=00 b=00
ata0: mask=03 status0=50 status1=00
ata0-master: ATA probe a=01 b=a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfc98
ata1: mask=03 status0=00 status1=00
ata1: mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI probe a=00 b=00
ata1-slave: ATAPI probe a=00 b=00
ata1: mask=03 status0=00 status1=00
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9 at
device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1: Philips Semiconductors product 0x1122, class 9/0, rev 1.10/1.10, addr 2
uhub1: 3 ports with 3 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.31, addr 3
umass0:0:0:-1: Attached to scbus0 as device 0
intpm0: <Intel 82371AB Power management controller> port 0x1040-0x104f irq 9
at device 7.3 on pci0
intpm0: I/O mapped 1040
intpm0: intr IRQ 9 enabled revision 0
using shared irq9.
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 8000
chip1: <Sony CXD3222 FireWire Host Controller> mem
0xfedf7c00-0xfedf7dff,0xfedf7000-0xfedf77ff irq 9 at device 8.0 on pci0
pcm0: <Yamaha DS-1E (YMF744)> port 0xfc8c-0xfc8f,0xfcc0-0xfcff mem
0xfedf8000-0xfedfffff irq 9 at device 9.0 on pci0
ds1: setmap (1000, 3de4), nseg=1, error=0
pcm0: ac97 codec id 0x414b4d02
pcm0: ac97 codec features headphone, 18 bit DAC, 18 bit ADC, 5 bit master
volume, AKM 3D Audio
pcm0: ac97 primary codec extended features AMAP
pcm: setmap 11000, 1000; 0xc9dbe000 -> 11000
pcm: setmap 21000, 1000; 0xc9dce000 -> 21000
pcm: setmap 31000, 1000; 0xc9dde000 -> 31000
pcm: setmap 41000, 1000; 0xc9dee000 -> 41000
pcm: setmap 51000, 1000; 0xc9dfe000 -> 51000
pcm: setmap 61000, 1000; 0xc9e0e000 -> 61000
pci0: <unknown card> (vendor=0x14f1, dev=0x2443) at 10.0 irq 9
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xfc40-0xfc7f mem
0xfec00000-0xfecfffff,0xfedf6000-0xfedf6fff irq 9 at device 11.0 on pci0
fxp0: Ethernet address 08:00:46:0d:8b:a9
bpf: fxp0 attached
pcic-pci0: <Ricoh RL5C475 PCI-CardBus Bridge> at device 12.0 on pci0
pcic-pci0: Legacy address set to 0x3e0
PCI Config space:
00: 04751180 02100007 06070080 00020000
10: 00000000 020000dc 00000000 00000000
20: 00000000 00000000 00000000 00000000
30: 00000000 00000000 00000000 078001ff
40: 8082104d 000003e1 00000000 00000000
50: 00000000 00000000 00000000 00000000
60: 00000000 00000000 00000000 00000000
70: 00000000 00000000 00000000 00000000
80: 00020001 00000000 04630463 30000000
90: 00000000 00000000 00000000 00000000
Cardbus Socket registers:
00: f000ff53: f000ff53: f000e2c3: f000ff53:
10: f000ff53: f000ff54: f000a1af: f000ff53:
ExCa registers:
00: eb 88 d5 43 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03
10: 00 00 fb 77 44 86 c4 c0 c8 02 08 e8 40 91 88 fe
20: 28 e0 8a 66 02 38 e0 72 02 88 e0 bf 05 00 c4 5e
30: 04 50 b4 02 cd 13 5b 73 0a 4f 74 1c 30 e4 cd 13
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: direction bit not set
fdc0: cmd 3 failed at out byte 1 of 3
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 73 02 0a
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83
b4 1f 00 4f 0d 0e 00 00 01 e0 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83
b4 1f 00 4f 0d 0e 00 00 01 e0 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0: <Intel i82365> at port 0x3e0 iomem 0xd4000 irq 10 on isa0
pcic0: management irq 10
stat is 33
pccard0: <PC Card bus -- kludge version> on pcic0
pcic1: not probed (disabled)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c200, tty 631212, net 671212
bpf: sl0 attached
bpf: faith0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
BRIDGE 990810, have 9 interfaces
-- index 1 type 6 phy 0 addrl 6 addr 08.00.46.0d.8b.a9
IPsec: Initialized Security Association Processing.
ata0-master: success setting UDMA2 on PIIX4 chip
Creating DISK ad0
Creating DISK wd0
ad0: <FUJITSU MHK2120AT/D834> ATA-5 disk at ata0-master
ad0: 11513MB (23579136 sectors), 23392 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
ad0: 11513MB <FUJITSU MHK2120AT> [23392/16/63] at ata0-master UDMA33
panic: rcmdlen = -1070593560 < 12, buffer too small
syncing disks...
CONFIGURATION FILE:
barry@gate$ cat VAIO
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.20 2000/10/31 23:16:07
n_hibma Exp $
machine i386
cpu I586_CPU
cpu I686_CPU
ident VAIO
maxusers 64
makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
options INVARIANT_SUPPORT
options INVARIANTS
options DDB
options DDB_UNATTENDED
options BREAK_TO_DEBUGGER
options BRIDGE #For vmware
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI peripherals (needed for USB umass driver)
device scbus # SCSI bus (required)
device da # Direct Access (disks)
#device sa # Sequential Access (tape etc)
#device cd # CD
device pass # Passthrough device (direct SCSI access)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
options SC_PIXEL_MODE
options SC_NORM_ATTR="(FG_LIGHTGREY|BG_BLACK)"
options SC_NORM_REV_ATTR="(FG_BLACK|BG_LIGHTGREY)"
options SC_KERNEL_CONS_ATTR="(FG_WHITE|BG_RED)"
options SC_KERNEL_CONS_REV_ATTR="(FG_RED|BG_BLACK)"
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd4000
device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
#device sio1 at isa? port IO_COM2 irq 3
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device wi
device an
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
#
# SMB bus
#
# System Management Bus support provided by the 'smbus' device.
#
# Supported devices:
# smb standard io
#
# Supported interfaces:
# iicsmb I2C to SMB bridge with any iicbus interface
# bktr brooktree848 I2C hardware interface
# intpm Intel PIIX4 Power Management Unit
# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
#
device smbus # Bus support, required for smb below.
device intpm
device alpm
device smb
device iicbus #Bus support, required for ic/iic/iicsmb below.
device iicbb
device ic
device iic
device iicsmb # smb over i2c bridge
# pcm: Luigi's sound driver
device pcm
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20001201211336.8019.qmail>