From owner-freebsd-questions Fri Dec 27 13:51:13 1996 Return-Path: Received: (from root@localhost) by freefall.freebsd.org (8.8.4/8.8.4) id NAA10283 for questions-outgoing; Fri, 27 Dec 1996 13:51:13 -0800 (PST) Received: from cs.tamu.edu (pophost.cs.tamu.edu [128.194.130.106]) by freefall.freebsd.org (8.8.4/8.8.4) with ESMTP id NAA10278 for ; Fri, 27 Dec 1996 13:51:05 -0800 (PST) Received: from mozart.cs.tamu.edu (mozart.cs.tamu.edu [128.194.146.209]) by cs.tamu.edu (8.8.4/8.8.4) with ESMTP id PAA09499; Fri, 27 Dec 1996 15:49:52 -0600 (CST) Received: (from mmehta@localhost) by mozart.cs.tamu.edu (8.8.4/8.8.4) id PAA01121; Fri, 27 Dec 1996 15:49:45 -0600 (CST) Date: Fri, 27 Dec 1996 15:49:44 -0600 (CST) From: "Miten N. Mehta" To: Carey Nairn cc: questions@freeBSD.org Subject: Re: DIAMOND STEALTH 64 and Free BSD. Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: owner-questions@freeBSD.org X-Loop: FreeBSD.org Precedence: bulk Hi, >This is almost identical to my setup. I have a Diamond Stealth 64, 2 MB >VRAM card with the S3 968 chipset and a ViewSonic 17PS monitor. You will >need to use the S3 server if you have a 968 card. If you have one of the >newer Virge chipset cards, you will need to use the S3V (or >something like that) server in XFree86-3.2. I used xf86config to set >it up first and then fine tuned it with xvidtune once it was running. I am almost done with configuring my XFree86 on (for FreeBSD) but I am facing one problem with this ... Problem: ...... --------------------------------------- First few pixel columns ( on left most part ) seems to be wrapped around to right most part - like half scroll bar column on the window which starts at extreme left can be seen on extreme right of the window. I read the whole chapter 7 and 8 of FreeBSD book and think that it is probably due to improper setting of register values, but don't know how to correct them so that the image on the screen is not wrapped around. If you know the solution of this problem or if you can tell any pointers for probable solution, it will be very helpful to me. Or if you can send me your "XF86Config" file that may also be helpful. -------------------------------- What I have done so far ..... I learned that my chipset was S3 vers. 968 with 2 MB VRAM with hori. Sync signal of 31.5 KHz - 96.6 KHz and Vert. Sync Signal 43.5 Hz - 120 Hz ( got information from www.diamondmm.com ). I also came to know about the monitor that it is ViewSonic 17GS with hori Freq. 30-69 KHz and vert Freq. 50-160 Hz. So I configured the video part by using "xf86config" and I am almost done. I was not getting it proper and I found out that due to less freq. resolution on monitor I was not able to get 1280*1024 mode and so I configured for 1024*768 ( and put comment for all other mode lines for modes like 800*600 and 640*480, and had to set virtual mode to 1024*768, because when it was 1280*1024, I was not getting whole screen at a time and when I move mouse out of the screen, I used to get remaining part ) and it is fine ... but still I have got the problem I told you as above. The mode line in XF86Config is as following, ... ******************************************** # 1024x768 @ 76 Hz, 62.5 kHz hsync modeline "1024x768" 85.00 1024 1028 1148 1360 768 784 787 823 output from of vditune ... ********************** Num hsync: 1, Num vsync: 1 hsync range 0: 30.00 - 69.00 vsync range 0: 50.00 - 160.00 "1024x768" 85.00 1024 1028 1148 1360 768 784 787 823 ------------------------------ Thanks again, >Cheers, >Carey Bye and take care. Miten. ---------------------------------------------------------------------- Miten N. Mehta Graduate Student 3902, Collegemain, #1001 Computer Science Bryan, Texas A & M University Texas-77801. College Station, TX-77843 Tel.#(409)-691-4614 E-mail# miten@tamu.edu Home Page : http://http.tamu.edu:8000/~mnm3866 ---------------------------------------------------------------------- "UNTIL YOUR DREAMS COME TRUE, KEEP ON WORKING FOR THAT" ----------------------------------------------------------------------