Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 3 Oct 1996 21:51:13 -0500 (CDT)
From:      Richard Cobbe <cobbe@cs.rice.edu>
To:        questions@freebsd.org
Subject:   General install question
Message-ID:  <199610040251.VAA28047@asia.cs.rice.edu>

Next in thread | Raw E-Mail | Index | Archive | Help

Sincerest apologies if these are FAQs, but I couldn't find them in the
mailing list archives or any of the other docs at www.freebsd.org.

I am not currently running any version of FreeBSD, but I'd like to install
it (2.1.5-RELEASE, fwiw) and check it out.  I have 2 IDE drives, and I'm
planning on installing BSD on the 3rd partition of the 2nd drive (both are
on the first IDE cable).

I have been told that the kernel which is installed as part of the process
expects to find itself on the first IDE device, and the system won't boot
(at least, won't boot BSD) if it's not there.  So, I have two questions:

1) Is this in fact the case?  If so, can I get around it by swapping the
drives, installing, recompiling the kernel to look for itself on the second
device (and changing /etc/fstab), and moving the driveFrom owner-freebsd-questions  Thu Oct  3 20:04:15 1996
Return-Path: owner-questions
Received: (from root@localhost)
          by freefall.freebsd.org (8.7.5/8.7.3) id UAA01027
          for questions-outgoing; Thu, 3 Oct 1996 20:04:15 -0700 (PDT)
Received: from s4.elec.uq.edu.au (s4.elec.uq.edu.au [130.102.96.4])
          by freefall.freebsd.org (8.7.5/8.7.3) with ESMTP id UAA01017
          for <freebsd-questions@freebsd.org>; Thu, 3 Oct 1996 20:04:01 -0700 (PDT)
Received: (from clary@localhost) by s4.elec.uq.edu.au (8.7.5/8.6.12) id NAA13703 for freebsd-questions@freebsd.org; Fri, 4 Oct 1996 13:03:51 +1000 (EST)
From: Clary Harridge <clary@elec.uq.edu.au>
Message-Id: <199610040303.NAA13703@s4.elec.uq.edu.au>
Subject: 2.15 release boot.flp missing adaptec 2940AU driver
To: freebsd-questions@freebsd.org
Date: Fri, 4 Oct 1996 13:03:50 +1000 (EST)
X-Mailer: ELM [version 2.4 PL25]
Content-Type: text
Sender: owner-questions@freebsd.org
X-Loop: FreeBSD.org
Precedence: bulk

Hi 
I have tried both the 
	2.1.5 RELEASE
and	2.2-960801-SNAP
floppies.

They seem to be missing the ahc driver which seems to be the one required
for an Adaptec 2940AU controller that I have on a pentium.
Maybe the probe is failing.

I can recognise my 3 SCSI drives using DOS.

Hardware
	120MHz pentium
	Adaptec AHA-2940AU.
	Seagate ST51080N
	2 x Seagate ST15150N
	2 x DEC etherworks PCI controller

Can anyone please throw any light on this?

-- 
regards			Dept. of Electrical Engineering,
Clary Harridge		University of Queensland, QLD, Australia, 4072
			Phone: +61-7-3365-3636	Fax:   +61-7-3365-4999
			INTERNET: clary@elec.uq.edu.au



Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?199610040251.VAA28047>