Date: Thu, 17 May 2001 16:12:44 -0700 From: Doug Hardie <bc979@lafn.org> To: "Jeffrey J. Mountin" <jeff-ml@mountin.net> Cc: freebsd-stable@freebsd.org Subject: Re: Hardware Problem Message-ID: <f04330145b72a0b01dd50@[10.0.1.100]> In-Reply-To: <4.3.2.20010517174928.02d75b00@207.227.119.2> References: <20010516014155.A19796@the-7.net> <20010516014155.A19796@the-7.net> <4.3.2.20010517174928.02d75b00@207.227.119.2>
next in thread | previous in thread | raw e-mail | index | archive | help
At 17:55 -0500 5/17/01, Jeffrey J. Mountin wrote:
>At 11:23 AM 5/17/01 -0700, Doug Hardie wrote:
>>One of my machines appears to have a hardware problem. When
>>booting 4.3-Release, it hangs for about 2 minutes between the two
>>console lines shown below. The first line is displayed and then it
>>hangs for about 2 minutes. Then the next line is displayed and the
>>boot completes. Any ideas which component is causing the problem?
>>Its a production server so I can't get much time for playing with
>>it. Its very consistent and does the same thing every time.
>
>It would help that you post the hardware you are using.
>
>A verbose boot would also help. Just mark where the pause is. The
>driver gurus will insist.
>
>Don't recall who offhand, but I helped with a shared IRQ issue on a
>newer board (Asus A7V) similar hardware. Doesn't look to be the
>case here. Unless this is new hardware or with the ATAPI you might
>have a kernel option that changed, if you upgraded that is.
>
I have several systems with basically the same hardware. The problem
only occurs on one of them. Here is the boot:
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-RELEASE #1: Fri May 11 16:39:12 PDT 2001
doug@zool.lafn.org:/usr/obj/usr/src/sys/ZOOK
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (551.25-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 134201344 (131056K bytes)
avail memory = 126324736 (123364K bytes)
Preloaded elf kernel "kernel" at 0xc043f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device
4.1 on pci0
2 minute delay here
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f
irq 9 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f
at device 4.3 on pci0
dc0: <82c169 PNIC 10/100BaseTX> port 0xd000-0xd0ff mem
0xe3000000-0xe30000ff irq 5 at device 10.0 on pci0
dc0: Ethernet address: 00:a0:cc:3e:87:dc
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <Trident model 9660 VGA-compatible display device> at 11.0 irq 12
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xb800-0xb8ff mem
0xe1800000-0xe1800fff irq 11 at device 12.0 on pci0
aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ep0 at port 0x300 iomem 0xd8000 irq 10 on isa0
ep0: Ethernet address 00:a0:24:7a:bf:e0
isa_compat: didn't get irq for lnc
ep1: <3Com 3C509-BNC EtherLink III> at port 0x300-0x30f irq 5 on isa0
ep1: No irq?!
ep1: ep_alloc() failed! (6)
device_probe_and_attach: ep1 attach returned 6
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST34573W 6244> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da1: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C)
cd0 at ahc0 bus 0 target 6 lun 0
cd0: <NEC CD-ROM DRIVE:464 1.04> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc0 bus 0 target 0 lun 0
da0: <COMPAQ DDRS-39130W S99C> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
dc0: promiscuous mode enabled
--
-- Doug
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?f04330145b72a0b01dd50>