From owner-freebsd-mobile Sat Jun 12 7:33:50 1999 Delivered-To: freebsd-mobile@freebsd.org Received: from rip.psg.com (rip.psg.com [147.28.0.39]) by hub.freebsd.org (Postfix) with ESMTP id 9D06714C07 for ; Sat, 12 Jun 1999 07:33:44 -0700 (PDT) (envelope-from randy@psg.com) Received: from localhost (12686 bytes) by rip.psg.com via sendmail with P:stdio/R:inet_resolve/T:smtp (sender: ) (ident using unix) id for ; Sat, 12 Jun 1999 07:33:44 -0700 (PDT) (Smail-3.2.0.101 1997-Dec-17 #1 built 1999-Apr-1) Message-Id: Date: Sat, 12 Jun 1999 07:33:44 -0700 (PDT) From: Randy Bush MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit To: FreeBSD Laptoppers Subject: wlp0 arplookup failed: could not allocate llinfo Sender: owner-freebsd-mobile@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org Sony VAIO 505TX 3.2-RELEASE PAO3-19990605.tar.gz [1] 3.2+PAO seems to work fine in general. but i still can not get wlp0 working with my 915MHz Digital RoamAbout/DS. dmesg appended [2], but the tasty bit is Card inserted, slot 0 card0: assign wlp0 iobase 0x240 irq 10 wlp0: nwid [0:0] mac:[8:0:e:21:49:fb] arplookup 147.28.2.1 failed: could not allocate llinfo arpresolve: can't allocate llinfo for 147.28.2.1rt i tried with wlp0 at both int 9 and int 10. the 3c589 works fine at int 10. i was seemingly able to successfully wlpconfig -i wlp0 -w 0xaaaa at least wlpconfig -i wlp0 -r read it back properly. kernel conf appended [3] randy ----- [1] - after the patch, at least two files seem to have the same content in them twice. i.e. the file had the whole content duplicated within it /sys/i386/conf/PAO_ALL /sys/i386/isa/if_wlp.c [2] - dmesg Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.2-RELEASE #0: Sat Jun 12 07:15:42 PDT 1999 root@roam.psg.com:/usr/src/sys/compile/ROAM-PAO Timecounter "i8254" frequency 1193182 Hz CPU: Pentium/P55C (quarter-micron) (298.44-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x582 Stepping=2 Features=0x8001bf real memory = 134217728 (131072K bytes) avail memory = 127791104 (124796K bytes) Preloaded elf kernel "kernel" at 0xc029b000. Probing for devices on PCI bus 0: chip0: rev 0x01 on pci0.0.0 chip1: rev 0x02 on pci0.7.0 ide_pci0: rev 0x01 on pci0.7.1 chip2: rev 0x02 on pci0.7.3 vga0: rev 0x01 int a irq 9 on pci0.8.0 pcic0: rev 0x00 int a irq 255 on pci0.10.0 RL5C4XX PCI Config Reg: [CSC isa irq] Probing for PnP devices: Probing for devices on the ISA bus: sc0 on isa sc0: VGA color <4 virtual consoles, flags=0x0> atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa psm0 irq 12 on isa psm0: model Generic PS/2 mouse, device ID 0 pcm1 at 0x220 irq 5 drq 1 on isa ESS1879 (rev 11, native mode) sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): wd0: 6194MB (12685680 sectors), 13424 cyls, 15 heads, 63 S/T, 512 B/S ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: on ppbus 0 lpt0: Interrupt-driven port lpt0: on ppbus 0 lpt0: Interrupt-driven port ep0 not found at 0x300 wlp0 not found at 0x300 pcic0 at 0x3e0-0x3e1 irq 11 on isa PC-Card ctlr(0) Ricoh RL5C475/476 [CardBus bridge mode] (5 mem & 2 I/O windows) pcic0: slot 0 controller I/O address 0x3e0 vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa npx0 on motherboard npx0: INT 16 interface apm0 on isa apm: found APM BIOS version 1.2 Intel Pentium detected, installing workaround for F00F bug changing root device to wd0s2a cmd ntpd pid 118 tried to use non-present sched_get_priority_min cmd ntpd pid 118 tried to use non-present sched_setscheduler Card inserted, slot 0 card0: assign wlp0 iobase 0x240 irq 10 wlp0: nwid [0:0] mac:[8:0:e:21:49:fb] arplookup 147.28.2.1 failed: could not allocate llinfo arpresolve: can't allocate llinfo for 147.28.2.1rt arplookup 147.28.2.1 failed: could not allocate llinfo arpresolve: can't allocate llinfo for 147.28.2.1rt wlp0: unload Return IRQ=10 Card removed, slot 0 Slot 0, unfielded interrupt (0) Card inserted, slot 0 card0: assign ep0 iobase 0x240 irq 10 ep0: utp/bnc[*UTP*] address 00:a0:24:ac:89:33 [3] - kernel conf # # Sample Laptop Configuration # for lenlen.ntc.keio.ac.jp (Toshiba Libretto 50CT) # Tatsumi Hosokawa # # For more information read the handbook part System Administration -> # Configuring the FreeBSD Kernel -> The Configuration File. # The handbook is available in /usr/share/doc/handbook or online as # latest version from the FreeBSD World Wide Web server # # # An exhaustive list of options and more detailed explanations of the # device lines is present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $Id: GENERIC,v 1.143.2.5 1999/03/29 17:59:38 ken Exp $ machine "i386" cpu "I386_CPU" cpu "I486_CPU" cpu "I586_CPU" cpu "I686_CPU" ident ROAM-PAO maxusers 64 #options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem #options MFS_ROOT #MFS usable as root device, "MFS" req'ed options NFS #Network Filesystem #options NFS_ROOT #NFS usable as root device, "NFS" req'ed options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem #options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] #options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor # You may need to reset all pccards after resuming options PCIC_RESUME_RESET # Detach SCSI devices when the SCSI card is removed #options SCSI_DETACH # Detach ATAPI devices when the ATA card is removed #options ATAPI_DETACH # Japanese version of WaveLAN PCMCIA uses 2.4GHz band instead of 915MHz # band that US version uses. If you want to use Japanese version of # WaveLAN, uncomment this line, or edit the corresponding config entry # of /etc/pccard.conf. #options "WAVELAN_PCMCIA_24" # Suspend the system when the battery status is "Low" #options "APM_BATT_LOW_SUSPEND" # If you want to use NTP on laptop machines, uncomment the following # option. Current APM implementation affects NTP client. #options "APM_NO_CLOCK_ADJUST" # PAO Enhanced PCI-PCIC support (experimental) #options CB_TEST #options FORCE_IRQ_ROUTING config kernel root on wd0 # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=24 # number of INTs controller isa0 controller pnp0 #controller eisa0 controller pci0 # Dont remove these two lines! pseudo-device card 1 # You must use "flags 0x1" when you don't hear any negotiation noise(?) # if you use modem card, or pccardd doesn't read cis tuple, tell you # 'No card in database for"(null)"("(null)")' in case of Cirrus Logic's # pcic is your PC. #device pcic0 at isa? port 0x3e0 flags 0x1 irq 11 device pcic0 at isa? port 0x3e0 irq 11 #device pcic0 at isa? port 0x3e4 irq 11 #device pcic1 at isa? port 0x3e2 # for HiNote Ultra II #device pcic1 at isa? port 0x3e4 # for Chandra II controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 disk fd0 at fdc0 drive 0 #disk fd1 at fdc0 drive 1 options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 #disk wd1 at wdc0 drive 1 #controller wdc1 at isa? port "IO_WD2" bio irq 15 #disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 #options ATAPI #Enable ATAPI support for IDE bus #options ATAPI_STATIC #Don't do it as an LKM #device acd0 #IDE CD-ROM #device wfd0 #IDE Floppy (e.g. LS-120) # A single entry for any of these controllers (ncr, ahb, ahc) is # sufficient for any number of installed devices. #controller ncr0 #controller ahb0 #controller ahc0 #controller isp0 #controller dpt0 #controller adv0 at isa? port ? cam irq ? #controller adw0 #controller bt0 at isa? port ? cam irq ? #controller aha0 at isa? port ? cam irq ? #controller scbus0 #device da0 #device sa0 #device pass0 #device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 #device mcd0 at isa? port 0x300 bio irq 10 #controller matcd0 at isa? port 0x230 bio #device scd0 at isa? port 0x230 bio # atkbdc0 controlls both the keyboard and the PS/2 mouse controller atkbdc0 at isa? port IO_KBD tty device atkbd0 at isa? tty irq 1 device psm0 at isa? tty irq 12 device vga0 at isa? port ? conflicts # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? tty options MAXCONS=4 # number of virtual consoles # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? tty #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std device npx0 at isa? port IO_NPX irq 13 # pcm: Luigi's sound driver device pcm1 at isa? port? tty irq 5 drq 1 flags 0x0 vector pcmintr # # Laptop support (see LINT for more options) # device apm0 at isa? # Advanced Power Management device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" tty irq 3 #device sio2 at isa? disable port "IO_COM3" tty irq 5 #device sio3 at isa? disable port "IO_COM4" tty irq 9 # Parallel port device ppc0 at isa? port? flags 0x40 net irq 7 controller ppbus0 device lpt0 at ppbus? #device plip0 at ppbus? #device ppi0 at ppbus? #controller vpo0 at ppbus? # # The following Ethernet NICs are all PCI devices. # #device ax0 # ASIX AX88140A #device de0 # DEC/Intel DC21x4x (``Tulip'') #device fxp0 # Intel EtherExpress PRO/100B (82557, 82558) #device mx0 # Macronix 98713/98715/98725 (``PMAC'') #device pn0 # Lite-On 82c168/82c169 (``PNIC'') #device rl0 # RealTek 8129/8139 #device tl0 # Texas Instruments ThunderLAN #device tx0 # SMC 9432TX (83c170 ``EPIC'') #device vr0 # VIA Rhine, Rhine II #device vx0 # 3Com 3c590, 3c595 (``Vortex'') #device wb0 # Winbond W89C840F #device xl0 # 3Com 3c90x (``Boomerang'', ``Cyclone'') # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. #device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 #device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000 device ep0 at isa? port 0x300 net irq 10 #device ep1 at isa? disable port 0x300 net irq 10 #device ex0 at isa? port? net irq? #device fe0 at isa? port 0x300 net irq 10 #device fe1 at isa? disable port 0x300 net irq 10 #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 #device lnc0 at isa? port 0x280 net irq 10 drq 0 #device sn0 at isa? port 0x300 net irq 10 #device sn1 at isa? disable port 0x300 net irq 10 device wlp0 at isa? port 0x300 net irq 10 #device wlp1 at isa? disable port 0x300 net irq 11 #device cs0 at isa? disable port 0x300 net irq ? #device cnw0 at isa? port 0x300 net irq 5 #device cnw1 at isa? disable port 0x300 net irq 5 #device ux0 device wi0 pseudo-device loop pseudo-device ether #pseudo-device sl 1 #pseudo-device ppp 1 pseudo-device tun 2 pseudo-device pty 16 #pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory and message queues. # options SYSVSHM options SYSVSEM options SYSVMSG # The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be # aware of the legal and administrative consequences of enabling this # option. The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. pseudo-device bpfilter 4 #Berkeley packet filter To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message