Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 20 Dec 2004 23:20:12 -0500
From:      linguae@lycos.com
To:        freebsd-questions@freebsd.org
Subject:   3Com Megahertz 3CXEM556 B Multifunction Card Not Working
Message-ID:  <20041221042012.B16DACA07F@ws7-4.us4.outblaze.com>

next in thread | raw e-mail | index | archive | help
Hello. I have problems trying to get my multifunction 3Com Megahertz=20
3CXEM556 B Ethernet/56K Modem PCMCIA card working on FreeBSD 5.1 on=20
my Compaq Armada 7400.  The card works perfectly (as far as the modem=20
part, can't test the ethernet portion) on Windows 98 SE. Whenever I=20
try to configure PPP for my card on FreeBSD, when I type the dialing=20
commands (such as at, atdt, etc.), the output on the screen would=20
either be jarbled or won't appear at all.

Here is my dmesg output:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE #0: Thu Jun  5 02:55:42 GMT 2003
     root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0689000.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 266677223 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (266.68-MHz 686-class CPU)
   Origin =3D "GenuineIntel"  Id =3D 0x652  Stepping =3D 2
=20=20=20
Features=3D0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CM=
OV,PAT,PSE36,MMX,FXSR>
real memory  =3D 67067904 (63 MB)
avail memory =3D 58134528 (55 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00f0970
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 0.1 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1250 PCI-CardBus Bridge> mem 0x7fffe000-0x7fffefff irq 11 at=20
device 12.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1250 PCI-CardBus Bridge> mem 0x7ffff000-0x7fffffff irq 11 at=20
device 12.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
isab0: <PCI-ISA bridge> at device 14.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <GENERIC ATA controller> port=20
0x1000-0x100f,0-0x3,0-0x7,0-0x3,0-0x7 at device 14.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0x44080000-0x44080fff irq=20
11 at device 14.2 on pci0
usb0: OHCI version 1.0
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
eisa0: <EISA bus> on motherboard
mainboard0: <DH@0000 (System Board)> on eisa0 slot 0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port=20
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0x200
sio1: port may not be enabled
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <SMCf010> can't assign resources (port)
Timecounters tick every 10.000 msec
ep0: <3Com Megahertz 3CXEM556 B> at port 0x100-0x10f irq 11 function=20
0 config 7 on pccard0
ep0: eeprom failed to come ready.
device_probe_and_attach: ep0 attach returned 6
sio4: <3Com Megahertz 3CXEM556 B> at port 0x110-0x117 irq 11 function=20
1 config 39 on pccard0
sio4: type 16550A with a bogus IIR_TXRDY register
sio4: unable to activate interrupt in fast mode - using normal mode
ad0: 4108MB <IBM-DKLA-24320> [8905/15/63] at ata0-master BIOSDMA
Mounting root from ufs:/dev/ad0s2a


I did read the ep man page; it did say that my card was "wedged"=20
(which, according to the Jargon File, means that the card doesn't=20
really work). I also used Google to see if other people had problems=20
with the same card, but I didn't find any solutions at all.  What do=20
I need to do in order to get my PCMCIA card working properly?  I am=20
relatively new to FreeBSD, so I don't really know where to go from=20
here.  Thanks in advance.

-linguae

----------------------------------------------
An Apple a day keeps the doctor away.
Proud supporter of Unix-based operating systems.

--=20
_______________________________________________
Find what you are looking for with the Lycos Yellow Pages
http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.as=
p?SRC=3Dlycos10



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20041221042012.B16DACA07F>