Date: Sun, 06 Dec 2015 23:10:16 +0100 From: Florian Ermisch <florian.ermisch@alumni.tu-berlin.de> To: perryh@pluto.rain.com,freebsd-stable@freebsd.org Subject: Re: ICH5 ATA DMA timeouts Message-ID: <845EDBE2-8111-4BFC-9EBE-ABDBE7A0FC53@alumni.tu-berlin.de> In-Reply-To: <5664A6DF.80205@multiplay.co.uk> References: <5663a618.157GXarwIXDEyml8%perryh@pluto.rain.com> <5664A6DF.80205@multiplay.co.uk>
next in thread | previous in thread | raw e-mail | index | archive | help
I had some onboard (S)ATA controllers becoming unreliable in the past. Two of them due to chipsets overheating under load which were fixable with additional cooling. In the third one we just added a cheap SATA card and spread the redundant disks between onboard and add-on controller to make a temporary failure a minor issue. Regards, Florian Am 6. Dezember 2015 22:21:35 MEZ, schrieb Steven Hartland <killing@multiplay.co.uk>: > Check cables and devices are in good condition. These things are > usually > a connectivity issue or device failing > > On 06/12/2015 03:06, Perry Hutchison wrote: > > Does anyone know the condition of the ICH5 ATA support in FreeBSD > 10? > > > > In preparing to repurpose an elderly Dell Dimension 4600 from > Windows > > to FreeBSD, and needing to decide what to do about drives, I found > > several mentions in the archives* of ICH5 ATA DMA timeouts -- mostly > > affecting the SATA ports, but the prevalence of SATA reports may > > just indicate which ports were getting the most use: a couple of > > the reports involved the PATA ports. > > > > While there have been commits to the ATA code since then, I didn't > > find any definitive statement that the DMA timeouts had been fixed. > > Did I miss something, or would I be better off using a separate SATA > > or PATA PCI card instead of the ICH5's built-in ports? > > > > Relevant parts of dmesg (with no hard drives attached): > > > > FreeBSD 10.2-RELEASE #0 r286666: Wed Aug 12 19:31:38 UTC 2015 > > root@releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC i386 > > CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.06-MHz 686-class CPU) > > Origin="GenuineIntel" Id=0xf34 Family=0xf Model=0x3 > Stepping=4 > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x441d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,xTPR> > > TSC: P-state invariant > > uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port > 0xff80-0xff9f irq 16 at device 29.0 on pci0 > > usbus0 on uhci0 > > uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port > 0xff60-0xff7f irq 19 at device 29.1 on pci0 > > usbus1 on uhci1 > > uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port > 0xff40-0xff5f irq 18 at device 29.2 on pci0 > > usbus2 on uhci2 > > uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port > 0xff20-0xff3f irq 16 at device 29.3 on pci0 > > usbus3 on uhci3 > > ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem > 0xffa80800-0xffa80bff irq 23 at device 29.7 on pci0 > > usbus4: EHCI version 1.0 > > usbus4 on ehci0 > > atapci0: <Intel ICH5 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf mem > 0xfeb7fc00-0xfeb7ffff irq 18 at device 31.1 on pci0 > > ata0: <ATA channel> at channel 0 on atapci0 > > ata1: <ATA channel> at channel 1 on atapci0 > > atapci1: <Intel ICH5 SATA150 controller> port > 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfea0-0xfeaf > irq 18 at device 31.2 on pci0 > > ata2: <ATA channel> at channel 0 on atapci1 > > ata3: <ATA channel> at channel 1 on atapci1 > > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > > pcm0: <Intel ICH5 (82801EB)> port 0xee00-0xeeff,0xedc0-0xedff mem > 0xfeb7fa00-0xfeb7fbff,0xfeb7f900-0xfeb7f9ff irq 17 at device 31.5 on > pci0 > > pcm0: primary codec not ready! > > pcm0: <Analog Devices AD1980 AC97 Codec (id = 0x41445370)> > > ata0: reset tp1 mask=00 ostat0=ff ostat1=ff > > ata1: reset tp1 mask=03 ostat0=00 ostat1=00 > > ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > > ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb > > ata1: reset tp2 stat0=00 stat1=00 devices=0x30000 > > ata2: SATA reset: ports status=0x00 > > ata2: p0: SATA connect timeout status=00000004 > > ata3: SATA reset: ports status=0x00 > > ata3: p0: SATA connect timeout status=00000004 > > pass0 at ata1 bus 0 scbus1 target 0 lun 0 > > pass0: <HL-DT-ST DVD-ROM GDR8163B 0D20> Removable CD-ROM SCSI device > > pass0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) > > pass1 at ata1 bus 0 scbus1 target 1 lun 0 > > pass1: <HL-DT-ST CD-RW GCE-8483B B105> Removable CD-ROM SCSI device > > pass1: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) > > cd0 at ata1 bus 0 scbus1 target 0 lun 0 > > cd0: <HL-DT-ST DVD-ROM GDR8163B 0D20> Removable CD-ROM SCSI device > > cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) > > cd0: Attempt to query device size failed: NOT READY, Medium not > present > > cd1 at ata1 bus 0 scbus1 target 1 lun 0 > > cd1: <HL-DT-ST CD-RW GCE-8483B B105> Removable CD-ROM SCSI device > > cd1: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) > > cd1: Attempt to query device size failed: NOT READY, Medium not > present - tray closed > > GEOM: new disk cd0 > > GEOM: new disk cd1 > > > > * Archive mentions, in http://lists.freebsd.org/pipermail/... > > > > freebsd-hardware/2004-September/thread.html#1924 > > freebsd-current/2005-February/thread.html#46719 > > freebsd-current/2005-February/thread.html#46737 > > freebsd-stable/2005-March/thread.html#13265 > > freebsd-stable/2007-May/thread.html#35061 > > freebsd-stable/2007-July/thread.html#36308 > > freebsd-bugs/2012-November/thread.html#50729 > > _______________________________________________ > > freebsd-stable@freebsd.org mailing list > > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > > To unsubscribe, send any mail to > "freebsd-stable-unsubscribe@freebsd.org" > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to > "freebsd-stable-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?845EDBE2-8111-4BFC-9EBE-ABDBE7A0FC53>