From owner-freebsd-current Sun Aug 22 13:38:52 1999 Delivered-To: freebsd-current@freebsd.org Received: from reliam.teaser.fr (reliam.teaser.fr [194.51.80.12]) by hub.freebsd.org (Postfix) with ESMTP id 6A0C814F8E; Sun, 22 Aug 1999 13:38:45 -0700 (PDT) (envelope-from nsouch@teaser.fr) Received: from teaser.fr (ppp1087-ft.teaser.fr [194.206.156.40]) by reliam.teaser.fr (8.9.3/8.9.3) with ESMTP id WAA03698; Sun, 22 Aug 1999 22:38:31 +0200 (MET DST) Received: (from nsouch@localhost) by teaser.fr (8.9.3/8.9.1) id WAA01578; Sun, 22 Aug 1999 22:21:03 +0200 (CEST) (envelope-from nsouch) Message-ID: <19990822222102.32308@breizh.teaser.fr> Date: Sun, 22 Aug 1999 22:21:02 +0200 From: Nicolas Souchu To: freebsd-current@FreeBSD.ORG Cc: soren@FreeBSD.ORG Subject: problem with the ata driver Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii X-Mailer: Mutt 0.81e X-Operating-System: FreeBSD breizh 4.0-CURRENT FreeBSD 4.0-CURRENT Sender: owner-freebsd-current@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hi there, hi Soren, First of all, the dump. >>>> Preloaded elf kernel "kernel" at 0xc0302000. Intel Pentium detected, installing workaround for F00F bug Probing for PnP devices: npx0: on motherboard npx0: INT 16 interface apm0: on motherboard apm: found APM BIOS version 1.2 pcib0: on motherboard pci0: on pcib0 chip0: at device 0.0 on pci0 isab0: at device 7.0 on pci0 ata-pci0: at device 7.1 on pci0 ata-pci0: Busmastering DMA supported ata0 at 0x01f0 irq 14 on ata-pci0 ahc0: irq 3 at device 9.0 on pci0 ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs vga-pci0: irq 11 at device 11.0 on pci0 fxp0: irq 9 at device 12.0 on pci0 fxp0: Ethernet address 00:90:27:3d:36:f9 devclass_alloc_unit: npx0 already exists, using next available unit number isa0: on motherboard fdc0: at port 0x3f0-0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> at fdc0 drive 0 atkbdc0: at port 0x60-0x6f on isa0 atkbd0: irq 1 on atkbdc0 psm0: irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: on isa0 sc0: on isa0 sc0: VGA color <16 virtual consoles, flags=0x0> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio2: not probed (disabled) sio3: not probed (disabled) ppc0 at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppb0: IEEE1284 device found /NIBBLE Probing for PnP devices on ppbus0: ppbus0: PRINTER HP ENHANCED PCL5,PJL plip0: on ppbus 0 lpt0: on ppbus 0 lpt0: Interrupt-driven port ppi0: on ppbus 0 isic0 at port 0x268 irq 5 flags 0x7 on isa0 isic0: USRobotics Sportster ISDN TA intern isic0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2) (Addr=0xc268) isic0: HSCX 82525 or 21525 Version 2.1 (AddrA=0x268, AddrB=0x4268) pca0 at port 0x40 on isa0 pca0: PC speaker audio driver ed0 at port 0x300-0x31f iomem 0xd8000-0xdbfff irq 10 on isa0 ed0: address 00:00:c0:37:f2:d0, type SMC8216/SMC8216C (16 bit) ep0: not probed (disabled) ata0: unwanted interrupt 1 status = ff i4b: ISDN call control device attached i4bisppp: 4 ISDN SyncPPP device(s) attached i4bctl: ISDN system control port attached i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression) i4btel: 2 ISDN telephony interface device(s) attached i4brbch: 4 raw B channel access device(s) attached i4btrc: 4 ISDN trace device(s) attached acd0: CDROM drive at ata0 as master acd0: drive speed 0KB/sec acd0: supported read types: acd0: Mechanism: caddy acd0: Medium: CD-ROM unknown medium Waiting 15 seconds for SCSI devices to settle changing root device to da0s1a da0 at ahc0 bus 0 target 1 lun 0 da0: Fixed Direct Access SCSI-2 device da0: 20.000MB/s transfers (10.000MHz, offset 8, 16bit) da0: 2063MB (4226725 512 byte sectors: 255H 63S/T 263C) da1 at ahc0 bus 0 target 2 lun 0 da1: Fixed Direct Access SCSI-2 device da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled da1: 4067MB (8330542 512 byte sectors: 255H 63S/T 518C) <<<< As you can see the drive is not properly detected. Note the "ata0: unwanted interrupt 1 status = ff" Any clue? The drive was running flawlessly with the old wdc driver and with various primary releases of the new ata driver (some, not all). Nicholas -- nsouch@teaser.fr / nsouch@freebsd.org FreeBSD - Turning PCs into workstations - http://www.FreeBSD.org To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message