Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 30 Aug 2005 20:04:10 -0400
From:      "Robert Ken Francis" <rkfrancis1@adelphia.net>
To:        "'Gary D. Margiotta'" <gary@tbe.net>
Cc:        freebsd-hardware@freebsd.org
Subject:   RE: Adaptec ATA RAID 1200A card supported?
Message-ID:  <000001c5adbf$83af7500$0a2e567e@monster4c>
In-Reply-To: <20050828110352.S43725@kerplunk.tbe.net>

next in thread | previous in thread | raw e-mail | index | archive | help
Thanks for responding.  I'm not sure what to do about this.  Someone in FreeBSD questions said it was related to atapi or SCSI.  The
1200A card has a Highpoint HPT370 chip on it.  I can see atapci1, ata2, and ata3.  Maybe the hard drives cause these driver
failures?

I can try to take out atapifd and see if the errors go away, which means I will have to build a kernel.  Does anyone know what
causes the below FAILUREs?

Thanks,
Rob

> -----Original Message-----
> From: owner-freebsd-hardware@freebsd.org 
> [mailto:owner-freebsd-hardware@freebsd.org] On Behalf Of Gary 
> D. Margiotta
> Sent: Sunday, August 28, 2005 11:13 AM
> To: Robert Ken Francis
> Cc: freebsd-hardware@freebsd.org
> Subject: Re: Adaptec ATA RAID 1200A card supported?
> 
> 
> The card itself is supported fine, the box I'm composing this 
> mail from is 
> using solely an Adaptec 1200A card, running 5-STABLE (which 
> was originally 
> installed with 5.2.1, and have been tracking -STABLE since).
> 
> I don't see the Adaptec card getting probed in your dmesg... 
> I see the 
> onboard SiS controller (atapci0 with ata0 and ata1), and a 
> HighPoint card 
> (atapci1 with ata-2 and ata-3), and the errors I see are 
> coming from the 
> ata-2 and ata-3 channels, which are on the HighPoint controller.
> 
> -Gary
> 
> On Sun, 28 Aug 2005, Robert Ken Francis wrote:
> 
> > I have failures like the below:
> >
> > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE 
> > status=51<READY,DSC,ERROR> error=4<ABORTED>
> >
> > What do I do to fix these failures?  All of the "FAILURE" 
> drives are 
> > on my Adaptec ATA RAID 1200A card.  My secondary built-in 
> IDE is dead 
> > so I have to use this card as an IDE replacement.
> >
> > Thanks,
> > Rob
> >
> > Note that NetBSD doesn't have this problem.
> >
> >
> > Here is my dmesg:
> >
> > Copyright (c) 1992-2005 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 
> 1992, 1993, 1994
> > 	The Regents of the University of California. All rights 
> reserved. FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005
> >    root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> > ACPI APIC Table: <ASUS   P4SP-MX >
> > Timecounter "i8254" frequency 1193182 Hz quality 0
> > CPU: Intel(R) Celeron(R) CPU 2.40GHz (2400.18-MHz 686-class CPU)  
> > Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
> >
> > 
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,P
> > GE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HT
> > T,TM,PBE>
> > real memory  = 1040171008 (991 MB)
> > avail memory = 1008295936 (961 MB)
> > ioapic0 <Version 8.0> irqs 0-23 on motherboard
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > acpi0: <ASUS P4SP-MX> on motherboard
> > acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20
> > acpi0: Power Button (fixed)
> > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> > acpi_timer0: <24-bit timer at 3.579545MHz> port 
> 0xe408-0xe40b on acpi0
> > cpu0: <ACPI CPU> on acpi0
> > acpi_throttle0: <ACPI CPU Throttling> on cpu0
> > acpi_button0: <Power Button> on acpi0
> > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> > pci0: <ACPI PCI bus> on pcib0
> > agp0: <SiS 651 host to AGP bridge> mem 
> 0xe8000000-0xebffffff at device 0.0 on pci0
> > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> > pci1: <ACPI PCI bus> on pcib1
> > pci1: <display, VGA> at device 0.0 (no driver attached)
> > isab0: <PCI-ISA bridge> at device 2.0 on pci0
> > isa0: <ISA bus> on isab0
> > atapci0: <SiS 962 UDMA133 controller> port 
> 0xa400-0xa40f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 16 at 
> device 2.5 on pci0
> > ata0: channel #0 on atapci0
> > ata1: channel #1 on atapci0
> > ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff 
> irq 20 at device 3.0 on pci0
> > usb0: OHCI version 1.0, legacy support
> > usb0: <SiS 5571 USB controller> on ohci0
> > usb0: USB revision 1.0
> > uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> > uhub0: 3 ports with 3 removable, self powered
> > ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff 
> irq 21 at device 3.1 on pci0
> > usb1: OHCI version 1.0, legacy support
> > usb1: <SiS 5571 USB controller> on ohci1
> > usb1: USB revision 1.0
> > uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> > uhub1: 3 ports with 3 removable, self powered
> > pci0: <serial bus, USB> at device 3.3 (no driver attached)
> > sis0: <SiS 900 10/100BaseTX> port 0x8800-0x88ff mem 
> 0xe5800000-0xe5800fff irq 19 at device 4.0 on pci0
> > miibus0: <MII bus> on sis0
> > rlphy0: <RTL8201L 10/100 media interface> on miibus0
> > rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > sis0: Ethernet address: 00:0e:a6:98:41:8b
> > atapci1: <HighPoint HPT370 UDMA100 controller> port 
> 0x7000-0x70ff,0x7400-0x7403,0x7800-0x7807,0x8000-0x8003,0x8400
> -0x8407 irq 17 at
> > device 14.0 on pci0
> > ata2: channel #0 on atapci1
> > ata3: channel #1 on atapci1
> > pci0: <multimedia, audio> at device 16.0 (no driver attached)
> > fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 
> 6 drq 2 on acpi0
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > ppc0: <ECP parallel printer port> port 
> 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/16 bytes threshold
> > ppbus0: <Parallel port bus> on ppc0
> > plip0: <PLIP network interface> on ppbus0
> > lpt0: <Printer> on ppbus0
> > lpt0: Interrupt-driven port
> > ppi0: <Parallel I/O> on ppbus0
> > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 
> flags 0x10 on acpi0
> > sio0: type 16550A
> > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> > atkbd0: <AT Keyboard> irq 1 on atkbdc0
> > kbd0 at atkbd0
> > psm0: <PS/2 Mouse> irq 12 on atkbdc0
> > psm0: model IntelliMouse, device ID 3
> > orm0: <ISA Option ROMs> at iomem 
> 0xcc000-0xd07ff,0xc0000-0xcbfff on isa0 pmtimer0 on isa0
> > sc0: <System console> at flags 0x100 on isa0
> > sc0: VGA <16 virtual consoles, flags=0x300>
> > sio1: configured irq 3 not in bitmap of probed irqs 0
> > sio1: port may not be enabled
> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 
> 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 
> 2400181916 Hz quality 800
> > Timecounters tick every 10.000 msec
> > ad0: 117246MB <Maxtor 6Y120L0/YAR41VW0> [238216/16/63] at 
> ata0-master UDMA133
> > acd0: DVDROM <COMPAQ DVD-ROM GDR8160B/0012> at ata0-slave PIO4
> > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=4<ABORTED>
> > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=4<ABORTED>
> > ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> > ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> > ad4: FAILURE - SETFEATURES ENABLE RCACHE 
> status=51<READY,DSC,ERROR> error=4<ABORTED>
> > ad4: FAILURE - SETFEATURES ENABLE WCACHE 
> status=51<READY,DSC,ERROR> error=4<ABORTED>
> > ad4: 40MB <MiniScribe Corporation 8051A/3.73> [745/4/28] at 
> ata2-master PIO0
> > ad5: FAILURE - SETFEATURES ENABLE WCACHE 
> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> > ad5: 41MB <Conner Peripherals 40MB - CP3041/S2.46> 
> [1053/2/40] at ata2-slave PIO0
> > ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ad6: FAILURE - SETFEATURES ENABLE WCACHE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ad6: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-master PIO0
> > ad7: FAILURE - SETFEATURES ENABLE WCACHE 
> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> > ad7: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-slave PIO0
> > ad4: FAILURE - READ status=51<READY,DSC,ERROR> 
> error=10<NID_NOT_FOUND> LBA=18 Mounting root from ufs:/dev/ad0s1a
> >
> > --
> > No virus found in this outgoing message.
> > Checked by AVG Anti-Virus.
> > Version: 7.0.344 / Virus Database: 267.10.16/83 - Release 
> Date: 8/26/2005
> >
> >
> > _______________________________________________
> > freebsd-hardware@freebsd.org mailing list 
> > http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
> > To unsubscribe, send any mail to 
> > "freebsd-hardware-unsubscribe@freebsd.org"
> >
> _______________________________________________
> freebsd-hardware@freebsd.org mailing list 
> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
> To unsubscribe, send any mail to 
> "freebsd-hardware-unsubscribe@freebsd.org"
> 
> -- 
> No virus found in this incoming message.
> Checked by AVG Anti-Virus.
> Version: 7.0.344 / Virus Database: 267.10.16/83 - Release 
> Date: 8/26/2005
>  
> 

-- 
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.344 / Virus Database: 267.10.17/84 - Release Date: 8/29/2005
 




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?000001c5adbf$83af7500$0a2e567e>