Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 9 Mar 2012 03:55:25 +1030
From:      David Walker <davidianwalker@gmail.com>
To:        freebsd-questions@freebsd.org
Subject:   Mouse disconnecting and reconnecting ...
Message-ID:  <CABE=bRMhTbEKn53A0KBgSFjAA5CcYV8pB6ojyQc39XCu8jvHMQ@mail.gmail.com>

Next in thread | Raw E-Mail | Index | Archive | Help
Hey.

I've recently installed 9.0 amd64 and X11 and Gnome.

Here is my rc.conf mouse stuff:

moused_nondefault_enable="NO"

Originally I'd bump the mouse and see it "doing stuff" on the console
and although it's a common mouse (a few weeks old) apparently it's
regarded as a "non-default" mouse.

I notice on the console (ttyv0) the following message repeated over
and over (say once a minute or so):

ugen4.2: <Microsoft> at usbus4 (disconnected)
ums0: at uhub4, port 2, addr 2 (disconnected)
ugen4.2: <Microsoft> at usbus4
ums0: <Microsoft Microsoft Basic Optical Mouse v2.0, class 0/0, rev
1.10/1.04, addr 2> on usbus4
ums0: 3 buttons and [XYZ] coordinates ID=0

I don't use mouse on the console so no problem.

Anyway, when I use Gnome, if I hover over something that can be
clicked or selected ... it will be clicked or selected without me
presing the left mouse button - this happens consistently and takes a
few seconds.
I'm not sure if those two things are connected (the message on the
console and the automatic mouse in Gnome) but I'm interested in
finding out.

dmesg follows.

Best wishes.

Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-RELEASE #0: Tue Jan  3 07:46:30 UTC 2012
    root@farrell.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
CPU: AMD Athlon(tm) II X2 250 Processor (3013.68-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x100f62  Family = 10  Model = 6  Stepping = 2
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x802009<SSE3,MON,CX16,POPCNT>
  AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x37ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT>
  TSC: P-state invariant
real memory  = 4294967296 (4096 MB)
avail memory = 4075315200 (3886 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <GBT    GBTUACPI>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <GBT GBTUACPI> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfce0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: Length mismatch for 3 range: 2ed00000 vs 2ee10000
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xef00-0xef7f mem
0xfb000000-0xfbffffff,0xd0000000-0xd7ffffff,0xde000000-0xdfffffff irq
18 at device 0.0 on pci1
nvidia0: <GeForce GT 520> on vgapci0
vgapci0: child nvidia0 requested pci_enable_io
vgapci0: child nvidia0 requested pci_enable_io
hdac0: <NVidia (Unknown) High Definition Audio Controller> mem
0xfcffc000-0xfcffffff irq 19 at device 0.1 on pci1
pcib2: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8111 B/C/CP/D/DP/E PCIe Gigabit Ethernet> port
0xde00-0xdeff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 18
at device 0.0 on pci2
re0: Using 1 MSI-X message
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 6c:f0:49:71:50:6b
ahci0: <ATI IXP700 AHCI SATA controller> port
0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f
mem 0xfe02f000-0xfe02f3ff irq 22 at device 17.0 on pci0
ahci0: AHCI v1.10 with 6 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
ohci0: <OHCI (generic) USB controller> mem 0xfe02e000-0xfe02efff irq
16 at device 18.0 on pci0
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xfe02d000-0xfe02dfff irq
16 at device 18.1 on pci0
usbus1: <OHCI (generic) USB controller> on ohci1
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe02c000-0xfe02c0ff
irq 17 at device 18.2 on pci0
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci2: <OHCI (generic) USB controller> mem 0xfe02b000-0xfe02bfff irq
18 at device 19.0 on pci0
usbus3: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xfe02a000-0xfe02afff irq
18 at device 19.1 on pci0
usbus4: <OHCI (generic) USB controller> on ohci3
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe029000-0xfe0290ff
irq 19 at device 19.2 on pci0
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP700/800 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on
pci0
ata0: <ATA channel 0> on atapci0
hdac1: <ATI SB600 High Definition Audio Controller> mem
0xfe024000-0xfe027fff irq 16 at device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
fwohci0: <Texas Instruments TSB43AB23> mem
0xfdeff000-0xfdeff7ff,0xfdef8000-0xfdefbfff irq 22 at device 14.0 on
pci3
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:35:48:3c:00:6c:f0:49
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:35:48:6c:f0:49
fwe0: Ethernet address: 02:35:48:6c:f0:49
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:35:48:3c:00:6c:f0:49 @ 0xfffe00000000,
S400, maxrec 2048
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x3a3c000
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
ohci4: <OHCI (generic) USB controller> mem 0xfe028000-0xfe028fff irq
18 at device 20.5 on pci0
usbus6: <OHCI (generic) USB controller> on ohci4
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x73 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me)
firewire0: bus manager 0
hdac0: HDA Codec #0: NVidia (Unknown)
hdac0: HDA Codec #1: NVidia (Unknown)
hdac0: HDA Codec #2: NVidia (Unknown)
hdac0: HDA Codec #3: NVidia (Unknown)
pcm0: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 0 nid 1 on hdac0
pcm1: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 1 nid 1 on hdac0
pcm2: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 2 nid 1 on hdac0
pcm3: <HDA NVidia (Unknown) PCM #0 DisplayPort> at cad 3 nid 1 on hdac0
hdac1: HDA Codec #0: Realtek ALC888
pcm4: <HDA Realtek ALC888 PCM #0 Analog> at cad 0 nid 1 on hdac1
pcm5: <HDA Realtek ALC888 PCM #1 Analog> at cad 0 nid 1 on hdac1
pcm6: <HDA Realtek ALC888 PCM #2 Digital> at cad 0 nid 1 on hdac1
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen6.1: <ATI> at usbus6
uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
uhub6: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <KINGSTON SV200S364G E111008a> ATA-9 SATA 3.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 61057MB (125045424 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 11772205 Hz quality 800
cd0 at ahcich1 bus 0 scbus1 target 0 lun 0
cd0: <ATAPI iHAS324   B AL1B> Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO 8192bytes)
cd0: cd present [313373 x 2048 byte records]
uhub2: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
ugen4.2: <Microsoft> at usbus4
ums0: <Microsoft Microsoft Basic Optical Mouse v2.0, class 0/0, rev
1.10/1.04, addr 2> on usbus4
ums0: 3 buttons and [XYZ] coordinates ID=0
Trying to mount root from ufs:/dev/ada0p2 [rw]...
ugen4.3: <NOVATEK> at usbus4
ukbd0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 3> on usbus4
kbd2 at ukbd0
uhid0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 3> on usbus4



Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?CABE=bRMhTbEKn53A0KBgSFjAA5CcYV8pB6ojyQc39XCu8jvHMQ>