Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 4 Jul 2007 15:17:33 +0700 (ICT)
From:      Olivier Nicole <on@cs.ait.ac.th>
To:        on@cs.ait.ac.th
Cc:        questions@freebsd.org
Subject:   Re: FreeBSD 5.5 hangs on boot when pluging mouse/Intel Gigabit
Message-ID:  <200707040817.l648HXZZ034086@banyan.cs.ait.ac.th>
In-Reply-To: <200706280816.l5S8GjJf053198@banyan.cs.ait.ac.th> (message from Olivier Nicole on Thu, 28 Jun 2007 15:16:45 %2B0700 (ICT))
References:  <200706280816.l5S8GjJf053198@banyan.cs.ait.ac.th>

next in thread | previous in thread | raw e-mail | index | archive | help
Hi,

> I am in process of upgrading a serie of servers from 4.11 to 5.5 (and
> them 6.2).
> 
> I am on the 5.5 phase. I did 2 machines sucessfully. On upgrading the
> thrid one, the boot will hang after SCSI buss reset, whenver I plug in
> the mouse or an Intel Pro/1000 MT Gigabit card.

I don't know the reason, but in 6.2 the problem vanished.

> The server I am upgrading was working fine for 2 years and more.
> 
> The 2 machines I did previously are the exact same mother board as the
> one making trouble, but the one I upgrade is 2 CPU. more RAM and a
> tape device.
> 
> One of the 2 machines that succeded is using the same add on Intel Pro
> Gigabit.
> 
> All machines are connected to the same KVM switch.
> 
> Kernel is GENERIC from distribution.
> 
> The exact place it hangs is shown in the dmesg bellow:
> 
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 5.5-RELEASE-p13 #2: Thu Jun 28 12:36:00 ICT 2007
>     root@amanda.cs.ait.ac.th:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel Pentium III (800.03-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
>   Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory  = 402632704 (383 MB)
> avail memory = 384299008 (366 MB)
> ACPI APIC Table: <ASUS   CUR-DLS >
> ioapic0 <Version 1.1> irqs 0-15 on motherboard
> ioapic1 <Version 1.1> irqs 16-31 on motherboard
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <ASUS CUR-DLS> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xfd800000-0xfd8fffff,0xfe000000-0xfe000fff irq 20 at device 2.0 on pci0
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp0: Ethernet address: 00:e0:18:0a:97:a6
> pci0: <display, VGA> at device 7.0 (no driver attached)
> isab0: <PCI-ISA bridge> port 0xe800-0xe80f at device 15.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <ServerWorks ROSB4 UDMA33 controller> port 0xd000-0xd00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
> ata0: channel #0 on atapci0
> ata1: channel #1 on atapci0
> ohci0: <OHCI (generic) USB controller> mem 0xfb000000-0xfb000fff irq 4 at device 15.2 on pci0
> usb0: OHCI version 1.0, legacy support
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 4 ports with 4 removable, self powered
> pcib1: <ACPI Host-PCI bridge> on acpi0
> pci1: <ACPI PCI bus> on pcib1
> sym0: <896> port 0xb800-0xb8ff mem 0xfa000000-0xfa001fff,0xfa800000-0xfa8003ff irq 24 at device 5.0 on pci1
> sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
> sym0: open drain IRQ line driver, using on-chip SRAM
> sym0: using LOAD/STORE-based firmware.
> sym0: handling phase mismatch from SCRIPTS.
> sym1: <896> port 0xb400-0xb4ff mem 0xf9000000-0xf9001fff,0xf9800000-0xf98003ff irq 25 at device 5.1 on pci1
> sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
> sym1: open drain IRQ line driver, using on-chip SRAM
> sym1: using LOAD/STORE-based firmware.
> sym1: handling phase mismatch from SCRIPTS.
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xc0000-0xca7ff on isa0
> pmtimer0 on isa0
> ppc0: parallel port not found.
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 8250 or not responding
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 800034408 Hz quality 800
> Timecounters tick every 10.000 msec
> acd0: CDROM <QSI CD-ROM SCR-242/CXAC> at ata0-master PIO4
> Waiting 15 seconds for SCSI devices to settle
> (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
> (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
> 
> ****** Hangs here *****
> 
> sa0 at sym1 bus 0 target 2 lun 0
> sa0: <TANDBERG SLR100 0402> Removable Sequential Access SCSI-2 device 
> sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
> da0 at sym0 bus 0 target 0 lun 0
> da0: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device 
> da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
> da0: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
> da1 at sym0 bus 0 target 1 lun 0
> da1: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device 
> da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
> da1: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
> da2 at sym0 bus 0 target 2 lun 0
> da2: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device 
> da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
> da2: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
> da3 at sym0 bus 0 target 3 lun 0
> da3: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device 
> da3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
> da3: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
> Mounting root from ufs:/dev/da0s1a
> 
> 
> Dmesg for one of the machine that is running fine, not the em0 at  the end.
> 
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD 5.5-RELEASE-p13 #0: Wed Jun 27 11:40:24 ICT 2007
>     root@database.cs.ait.ac.th:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel Pentium III (800.03-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
>   Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory  = 134197248 (127 MB)
> avail memory = 121659392 (116 MB)
> ACPI APIC Table: <ASUS   CUR-DLS >
> ioapic0 <Version 1.1> irqs 0-15 on motherboard
> ioapic1 <Version 1.1> irqs 16-31 on motherboard
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <ASUS CUR-DLS> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xfd800000-0xfd8fffff,0xfe000000-0xfe000fff irq 20 at device 2.0 on pci0
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp0: Ethernet address: 00:e0:18:0a:97:d7
> em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xd400-0xd43f mem 0xfc800000-0xfc81ffff,0xfd000000-0xfd01ffff irq 19 at device 6.0 on pci0
> em0: Ethernet address: 00:07:e9:2a:76:13
> pci0: <display, VGA> at device 7.0 (no driver attached)
> isab0: <PCI-ISA bridge> port 0xe800-0xe80f at device 15.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <ServerWorks ROSB4 UDMA33 controller> port 0xb800-0xb80f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
> ata0: channel #0 on atapci0
> ata1: channel #1 on atapci0
> ohci0: <OHCI (generic) USB controller> mem 0xfa000000-0xfa000fff irq 9 at device 15.2 on pci0
> usb0: OHCI version 1.0, legacy support
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 4 ports with 4 removable, self powered
> pcib1: <ACPI Host-PCI bridge> on acpi0
> pci1: <ACPI PCI bus> on pcib1
> sym0: <896> port 0xb400-0xb4ff mem 0xf9000000-0xf9001fff,0xf9800000-0xf98003ff irq 24 at device 5.0 on pci1
> sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
> sym0: open drain IRQ line driver, using on-chip SRAM
> sym0: using LOAD/STORE-based firmware.
> sym0: handling phase mismatch from SCRIPTS.
> sym1: <896> port 0xb000-0xb0ff mem 0xf8000000-0xf8001fff,0xf8800000-0xf88003ff irq 25 at device 5.1 on pci1
> sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
> sym1: open drain IRQ line driver, using on-chip SRAM
> sym1: using LOAD/STORE-based firmware.
> sym1: handling phase mismatch from SCRIPTS.
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse, device ID 3
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> sio0: type 16550A
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> ppc0: <ECP parallel printer port> port 0x778-0x77a,0x378-0x37f irq 7 drq 3 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xc0000-0xca7ff on isa0
> pmtimer0 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 800034534 Hz quality 800
> Timecounters tick every 10.000 msec
> acd0: CDROM <HL-DT-ST CD-ROM GCR-8522B/1.01> at ata0-master PIO4
> Waiting 15 seconds for SCSI devices to settle
> (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
> (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
> da0 at sym0 bus 0 target 0 lun 0
> da0: <SEAGATE ST318437LW 0105> Fixed Direct Access SCSI-3 device 
> da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
> da0: 17547MB (35937500 512 byte sectors: 255H 63S/T 2237C)
> Mounting root from ufs:/dev/da0s1a
> em0: Link is up 1000 Mbps Full Duplex



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200707040817.l648HXZZ034086>