Date: Mon, 27 Mar 2006 16:35:18 -0500 From: "Huy Ton That" <huyslogic@gmail.com> To: questions@freebsd.org Subject: 3ware 9550SX-8LP RAID help Message-ID: <1cac28080603271335m41c91a9cq55222093f89f8128@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Hello I just purchased a new server and was installing FBSD. It currently has 2 internal harddrives which are working and mountable. Additionally there are 3 hotswappable hdds which are connected to a 3ware 9550sx-8LP rai= d 5/0 controller card. Everything has been configured properly within the controller's bios. However, the controller is not detected during boot time. I found out that the 'twa' drivers should take care of this, and after consulting the online manpages I saw... however it said FreeBSD 7.0 below at the bottom of the online manpage... *HARDWARE* <http://www.freebsd.org/cgi/man.cgi?query=3Dtwa&sektion=3D4&manp= ath=3DFreeBSD+7.0-current#end> The *twa* driver supports the following SATA RAID controllers: *=B7*=09 AMCC's 3ware 9500S-4LP *=B7*=09 AMCC's 3ware 9500S-8 *=B7*=09 AMCC's 3ware 9500S-8MI *=B7*=09 AMCC's 3ware 9500S-12 *=B7*=09 AMCC's 3ware 9500S-12MI *=B7*=09 AMCC's 3ware 9500SX-4LP *=B7*=09 AMCC's 3ware 9500SX-8LP *=B7*=09 AMCC's 3ware 9500SX-12 *=B7*=09 AMCC's 3ware 9500SX-12MI *=B7*=09 AMCC's 3ware 9500SX-16ML *=B7*=09 AMCC's 3ware 9550SX-4LP *=B7*=09 AMCC's 3ware 9550SX-8LP *=B7*=09 AMCC's 3ware 9550SX-12 *=B7*=09 AMCC's 3ware 9550SX-12MI *=B7*=09 AMCC's 3ware 9550SX-16ML The odd thing is that when I do man twa locally on the machine, this is all I have on my list: o AMCC's 3ware 9500S-4LP o AMCC's 3ware 9500S-8 o AMCC's 3ware 9500S-8MI o AMCC's 3ware 9500S-12 o AMCC's 3ware 9500S-12MI Is this just what is supported for FreeBSD 6.0? I tried loading the twa locally from the box and received the following message: kldload twa module_register: module pci/twa already exists! Module pci/twa failed to register: 17 kldload: can't load twa: File exists kldunload twa kldunload: can't find file twa: No such file or directory uname -a FreeBSD localhost.CASO 6.0-RELEASE FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005 root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC i386 localhost# cat /var/run/dmesg.boot Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005 root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC ACPI APIC Table: <IntelR AWRDACPI> Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2792.06-MHz 686-class CPU) Origin =3D "GenuineIntel" Id =3D 0xf29 Stepping =3D 9 Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,= MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=3D0x4400<CNTX-ID,<b14>> real memory =3D 535691264 (510 MB) avail memory =3D 514867200 (491 MB) ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <IntelR AWRDACPI> on motherboard acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0 pci_link1: <ACPI PCI Link LNKB> irq 11 on acpi0 pci_link2: <ACPI PCI Link LNKC> irq 11 on acpi0 pci_link3: <ACPI PCI Link LNKD> irq 5 on acpi0 pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0 pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0 pci_link6: <ACPI PCI Link LNK0> irq 0 on acpi0 pci_link7: <ACPI PCI Link LNK1> irq 9 on acpi0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pci1: <ACPI PCI bus> on pcib1 em0: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port 0xb000-0xb01f mem 0xf6000000-0xf601ffff irq 18 at device 1.0 on pci1 em0: Ethernet address: 00:30:48:87:be:ec em0: Speed:N/A Duplex:N/A pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pci2: <mass storage, RAID> at device 1.0 (no driver attached) uhci0: <UHCI (generic) USB controller> port 0xe100-0xe11f irq 16 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xe000-0xe01f irq 19 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <base peripheral> at device 29.4 (no driver attached) pci0: <base peripheral, interrupt controller> at device 29.5 (no driver attached) ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf6100000-0xf61003ff irq 23 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 4 ports with 4 removable, self powered pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pci3: <display, VGA> at device 9.0 (no driver attached) em1: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port 0xd100-0xd13f mem 0xf5000000-0xf501ffff irq 19 at device 10.0 on pci3 em1: Ethernet address: 00:30:48:87:be:ed em1: Speed:N/A Duplex:N/A isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel 6300ESB UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 atapci1: <Intel 6300ESB SATA150 controller> port 0xe200-0xe207,0xe300-0xe303,0xe400-0xe407,0xe500-0xe503,0xe600-0xe60f at device 31.2 on pci0 atapci1: failed to enable memory mapping! ata2: <ATA channel 0> on atapci1 ata3: <ATA channel 1> on atapci1 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_tz0: <Thermal Zone> on acpi0 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0: <Standard parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 o= n acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=3D0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2792057296 Hz quality 800 Timecounters tick every 1.000 msec acd0: DVDROM <SONY DVD-ROM DDU1615/FYS3> at ata0-master UDMA33 ad4: 157066MB <HDT722516DLA380 V43OA91A> at ata2-master SATA150 ad6: 157066MB <HDT722516DLA380 V43OA91A> at ata3-master SATA150 Trying to mount root from ufs:/dev/ad4s1a I don't know what else to do, does anyone know how to get this recognized? I've spent all morning trying to get this figured out :/.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1cac28080603271335m41c91a9cq55222093f89f8128>