Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 15 May 2008 20:27:46 +0200
From:      Aragon Gouveia <aragon@phat.za.net>
To:        Jeff <jeff@doeshosting.com>
Cc:        freebsd-multimedia@freebsd.org
Subject:   Re: Fwd: pvr-xxx on 7.0
Message-ID:  <20080515182746.GA14203@phat.za.net>
In-Reply-To: <CFAA6030-A326-4B2A-A33A-2867ECCED0D2@doeshosting.com>
References:  <F8A4DB3A-80CB-46BB-B4E4-7AC6E6750A3A@doeshosting.com> <CFAA6030-A326-4B2A-A33A-2867ECCED0D2@doeshosting.com>

next in thread | previous in thread | raw e-mail | index | archive | help
| By Jeff <jeff@doeshosting.com>
|                                          [ 2008-05-15 19:40 +0200 ]
> >>the port is updated @  http://usleepless.110mb.com/pvrxxx_port.tgz
> >>
> >>- should build flawless on 7.0
> >>- now unloads firmware-kld-modules
> >>- "make makesum" should not be necessary
> >>- should be able to switch back from svga/composite to tuner
> >>- added 3:2 pulldown control in pvr250-setchannel to see if it  
> >>makes a
> >>difference for anybody
> >>
> >>i observed something strange on 7.0 with this driver. mplayer is now
> >>able to sync a/v properly when doing "mplayer /dev/cxm0". i would  
> >>like
> >>to hear from others about this.
> >>
> >>regards,
> >>
> >>usleepless

Thanks for the update!

The new port compiles and installs fine.  The modules load with the
following logged:

May 15 20:17:12 <kern.crit> geek kernel: cxm0: <Conexant iTVC15 MPEG Coder> mem 0xf4000000-0xf7ffffff irq 10 at device 4.0 on pci5
May 15 20:17:12 <kern.crit> geek kernel: cxm_iic0: <Conexant iTVC15 / iTVC16 I2C controller> on cxm0
May 15 20:17:12 <kern.crit> geek kernel: iicbb0: <I2C bit-banging driver> on cxm_iic0
May 15 20:17:12 <kern.crit> geek kernel: iicbus0: <Philips I2C bus> on iicbb0 master-only
May 15 20:17:12 <kern.crit> geek kernel: iicbus0: <unknown card> at addr 0
May 15 20:17:12 <kern.crit> geek kernel: iicbus0: <unknown card> at addr 0
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: ivtv version
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: Hauppauge: model = 48139, rev = K2B7, serial# = 8694227
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: tuner = Philips FM1216ME MK5 (idx = 117, type = 38)
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: audio processor = MSP4418 (type = 19)
May 15 20:17:12 <kern.info> geek kernel: <2>tveeprom: decoder processor = SAA7115 (type = 13)
May 15 20:17:12 <kern.crit> geek kernel: tuner type: 38
May 15 20:17:12 <kern.crit> geek kernel: cxm0: Eeprom PAL
May 15 20:17:12 <kern.info> geek kernel: tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by cxm
May 15 20:17:12 <kern.info> geek kernel: tuner: switching to v4l2
May 15 20:17:12 <kern.crit> geek kernel: before tuner_command!
May 15 20:17:12 <kern.info> geek kernel: tuner: tv freq set to 55.25
May 15 20:17:12 <kern.info> geek kernel: tuner: tv 0x05 0xe3 0x8e 0x01
May 15 20:17:13 <kern.crit> geek kernel: cxm0: SAA7115 rev 1 video decoder
May 15 20:17:13 <kern.crit> geek kernel: cxm0: MSP4418G-B3 audio decoder
May 15 20:17:13 <kern.crit> geek kernel: cxm0: IR Remote
May 15 20:17:13 <kern.crit> geek kernel: cxm0: [ITHREAD]
May 15 20:17:15 <kern.debug> geek kernel: cxm0: encoder firmware version 0x2060039
May 15 20:17:15 <kern.debug> geek kernel: cxm0: decoder firmware version 0x2020023


However, I'm not able to pull video off the device:

# cat /dev/cxm0 >test.mpg
cat: /dev/cxm0: Device not configured

and this gets logged:

May 15 20:17:35 <kern.crit> geek kernel: cxm0: video decoder isn't locked
May 15 20:17:35 <kern.debug> geek kernel: Could not detect FPS
May 15 20:17:35 <kern.debug> geek kernel: could not config dec
May 15 20:17:35 <kern.debug> geek kernel: could not start encoder


Trying to select the tuner with pvr250-setchannel results in:

# pvr250-setchannel -t
ioctl( tfd, METEORSINPUT ) failed.: Invalid argument
May 15 20:24:48 <kern.crit> geek kernel: cxm0: video decoder failed to lock


Any more help appreciated.  Must be close now. :)


Thanks,
Aragon



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080515182746.GA14203>