Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 6 May 2002 23:41:49 +1000
From:      "Scott Penno" <scott.penno@gennex.com.au>
To:        <freebsd-current@FreeBSD.ORG>, <freebsd-mobile@FreeBSD.ORG>
Subject:   Re: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
Message-ID:  <002801c1f503$c6db1c80$0128a8c0@SCOTT>
References:  <000201c1f377$e7668d00$0128a8c0@SCOTT> <004e01c1f4ec$56f52490$0128a8c0@SCOTT>

next in thread | previous in thread | raw e-mail | index | archive | help
I removed apm from the kernel which appeared to be playing having with acpi
and things are now working a treat.  The card works fine, however I do
receive the following message, 'cardbus0: <unknown card> (vendor=0x115d,
dev=0x0103) at 0.1 irq 5'.  I've had a look through various lists and
couldn't find a resolution.  Is this a real drama and if so, how do I
correct it?

Regards,

Scott



----- Original Message -----
From: "Scott Penno" <scott.penno@gennex.com.au>
To: <freebsd-current@FreeBSD.ORG>; <freebsd-mobile@FreeBSD.ORG>
Sent: Monday, May 06, 2002 8:54 PM
Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G


> Just an update.  I've tried three different 32 bit cards and every time
the
> card was inserted the laptop locked up.  I recompiled the kernel without
the
> miibus and dc and then inserted the Xircom card the laptop would appear to
> lock up, that is, everything that was running just stopped.  When the card
> was re-inserted, everything would come back to life and a console message
> would appear reporting 'pccbb0: Cardbus card activation failed'.  A
similar
> result was experienced with the other cards.  With that said, I'm still no
> closer to identifying the cause of these problems.  Any ideas?
>
> Scott.
>
>
>
> ----- Original Message -----
> From: "Scott Penno" <scott.penno@gennex.com.au>
> To: <freebsd-current@FreeBSD.ORG>; <freebsd-mobile@FreeBSD.ORG>
> Sent: Sunday, May 05, 2002 12:27 AM
> Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G [DRAFT]
>
>
> > Hi there,
> >
> > I've been attempting to get my Xircom Realport CBEM56G working under
> CURRENT
> > for some time without success.  I grabbed the latest source on 03/05
> 12:00PM
> > GMT and compiled without a problem.  I have a 3Com Etherlink III 3C589D
> card
> > which is a 16 bit card which I can insert and use without a problem.
> > However when I try and insert my Xircom Realport CBEM56G, my laptop
locks
> > up.
> > Under 4.X the cardbus bridge caused some intial problems getting
> configured
> > but once working, worked a treat and I suspect this is where the current
> > problem is.  Without the kernel option PCI_ALLOW_UNSUPPORTED_IO_RANGE
with
> > NEWCARD, I'm unable to
> > acheive any card functionality, when compiled with this option the 16
bit
> > 3Com card works fine but the 32bit Xircom card causes a lockup.
> Interesting
> > to note also that under Windows XP and FreeBSD 4.X the bridge is
detected
> as
> > an OZ6933, while under FreeBSD 5.X it's detected as an OZ6833.
> > Not sure where to go from here so any assistance appreciated.  I've
> included
> > a dmesg from boot -v with the 3Com card, console messages when the
Xircom
> > card is inserted until the lockup occurs and finally the kernel
> > configuration file.
> >
> > Regards,
> >
> > Scott.
> >
> >
> >
> > Copyright (c) 1992-2002 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> >  The Regents of the University of California. All rights reserved.
> > FreeBSD 5.0-CURRENT #2: Sat May  4 12:13:42 EST 2002
> >     root@jupiter.gennex.com.au:/usr/obj/usr/src/sys/JUPITER
> > Preloaded elf kernel "/boot/kernel/kernel" at 0xc043b000.
> > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc043b0b4.
> > Calibrating clock(s) ... TSC clock: 897239123 Hz, i8254 clock: 1193138
Hz
> > CLK_USE_I8254_CALIBRATION not specified - using default frequency
> > Timecounter "i8254"  frequency 1193182 Hz
> > CLK_USE_TSC_CALIBRATION not specified - using old calibration method
> > TSC initialization skipped: APM enabled.
> > CPU: Pentium III/Pentium III Xeon/Celeron (897.28-MHz 686-class CPU)
> >   Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
> >
> >
>
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
> > PAT,PSE36,MMX,FXSR,SSE>
> > real memory  = 266797056 (260544K bytes)
> > Physical memory chunk(s):
> > 0x00001000 - 0x0009efff, 647168 bytes (158 pages)
> > 0x00462000 - 0x0fe67fff, 262168576 bytes (64006 pages)
> > avail memory = 254808064 (248836K bytes)
> > bios32: Found BIOS32 Service Directory header at 0xc00f66b0
> > bios32: Entry = 0xfd890 (c00fd890)  Rev = 0  Len = 1
> > pcibios: PCI BIOS entry at 0xfd890+0x13a
> > pnpbios: Found PnP BIOS data at 0xc00f6700
> > pnpbios: Entry = f0000:a2a6  Rev = 1.0
> > Other BIOS signatures found:
> > null: <null device, zero device>
> > random: <entropy source>
> > mem: <memory & I/O>
> > Pentium Pro MTRR support enabled
> > VESA: information block
> > 56 45 53 41 00 03 00 01 00 01 01 00 00 00 40 00
> > 00 01 10 00 00 01 31 01 00 01 43 01 00 01 5d 01
> > 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > VESA: 16 mode(s) found
> > VESA: v3.0, 1024k memory, flags:0x1, mode table:0xc03895c0 (1000040)
> > VESA: Intel815M(TM) Graphics Chip Accelerated VGA BIOS
> > VESA: Intel Corporation i815M Graphics Controller Hardware Version 0.0
> > pci_open(1): mode 1 addr port (0x0cf8) is 0x80001004
> > pci_open(1a): mode1res=0x80000000 (0x80000000)
> > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086)
> > Using $PIR table, 7 entries at 0xc00fdf50
> > apm0: <APM BIOS> on motherboard
> > apm0: found APM BIOS v1.2, connected at v1.2
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > acpi0: Other PM system enabled.
> > pcib0: <Intel 82815 (i815 GMCH) Host To Hub bridge> at pcibus 0 on
> > motherboard
> > pci0: physical bus=0
> > found-> vendor=0x8086, dev=0x1130, revid=0x11
> >  bus=0, slot=0, func=0
> >  class=06-00-00, hdrtype=0x00, mfdev=0
> >  map[10]: type 3, range 32, base f8000000, size 26, enabled
> >  map[14]: type 1, range 32, base f4000000, size 19, enabled
> > found-> vendor=0x8086, dev=0x1132, revid=0x11
> >  bus=0, slot=2, func=0
> >  class=03-00-00, hdrtype=0x00, mfdev=0
> >  intpin=a, irq=10
> >  powerspec 2  supports D0 D3  current D0
> > found-> vendor=0x8086, dev=0x2448, revid=0x03
> >  bus=0, slot=30, func=0
> >  class=06-04-00, hdrtype=0x01, mfdev=0
> > found-> vendor=0x8086, dev=0x244c, revid=0x03
> >  bus=0, slot=31, func=0
> >  class=06-01-00, hdrtype=0x00, mfdev=1
> >  map[20]: type 4, range 32, base 00001800, size  4, enabled
> > found-> vendor=0x8086, dev=0x244a, revid=0x03
> >  bus=0, slot=31, func=1
> >  class=01-01-80, hdrtype=0x00, mfdev=0
> >  map[20]: type 4, range 32, base 00001820, size  5, enabled
> > found-> vendor=0x8086, dev=0x2442, revid=0x03
> >  bus=0, slot=31, func=2
> >  class=0c-03-00, hdrtype=0x00, mfdev=0
> >  intpin=d, irq=5
> >  map[20]: type 4, range 32, base 00001810, size  4, enabled
> > found-> vendor=0x8086, dev=0x2443, revid=0x03
> >  bus=0, slot=31, func=3
> >  class=0c-05-00, hdrtype=0x00, mfdev=0
> >  intpin=b, irq=5
> >  map[20]: type 4, range 32, base 00001880, size  5, enabled
> > found-> vendor=0x8086, dev=0x2444, revid=0x03
> >  bus=0, slot=31, func=4
> >  class=0c-03-00, hdrtype=0x00, mfdev=0
> >  intpin=c, irq=5
> >  map[10]: type 4, range 32, base 00001c00, size  8, enabled
> >  map[14]: type 4, range 32, base 00001840, size  6, enabled
> > found-> vendor=0x8086, dev=0x2445, revid=0x03
> >  bus=0, slot=31, func=5
> >  class=04-01-00, hdrtype=0x00, mfdev=0
> >  intpin=b, irq=5
> > pci0: <PCI bus> on pcib0
> > agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem
> > 0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 10 at device 2.0 on pci0
> > agp0: allocating GATT for aperture of size 64M
> > pcib1: <PCI-PCI bridge> at device 30.0 on pci0
> > pcib1:   secondary bus     1
> > pcib1:   subordinate bus   1
> > pcib1:   I/O decode        0xf000-0xfff
> > pcib1:   memory decode     0xfff00000-0xfffff
> > pcib1:   prefetched decode 0xfff00000-0xfffff
> > pci1: physical bus=1
> > found-> vendor=0x1217, dev=0x6933, revid=0x01
> >  bus=1, slot=3, func=0
> >  class=06-07-00, hdrtype=0x02, mfdev=1
> >  intpin=a, irq=9
> >  powerspec 2  supports D0 D1 D2 D3  current D0
> > found-> vendor=0x1217, dev=0x6933, revid=0x01
> >  bus=1, slot=3, func=1
> >  class=06-07-00, hdrtype=0x02, mfdev=1
> >  intpin=b, irq=9
> >  powerspec 2  supports D0 D1 D2 D3  current D0
> > pci1: <PCI bus> on pcib1
> > pccbb0: <O2Mirco OZ6833 PCI-CardBus Bridge> irq 9 at device 3.0 on pci1
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > pcib1: device pccbb0 requested unsupported memory range
> > 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> > pcib1: device pccbb0 requested decoded memory range
0x84000000-0xffffffff
> > cardbus0: <CardBus bus> on pccbb0
> > pccard0: <16-bit PCCard bus> on pccbb0
> > pccbb1: <O2Mirco OZ6833 PCI-CardBus Bridge> irq 9 at device 3.1 on pci1
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > pcib1: device pccbb1 requested unsupported memory range
> > 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> > pcib1: device pccbb1 requested decoded memory range
0x84000000-0xffffffff
> > cardbus1: <CardBus bus> on pccbb1
> > pccard1: <16-bit PCCard bus> on pccbb1
> > isab0: <PCI-ISA bridge> at device 31.0 on pci0
> > isa0: <ISA bus> on isab0
> > atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device
31.1
> on
> > pci0
> > ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1800
> > ata0: mask=03 ostat0=50 ostat2=00
> > ata0-master: ATAPI 00 00
> > ata0-slave: ATAPI 00 00
> > ata0: mask=03 stat0=50 stat1=00
> > ata0-master: ATA 01 a5
> > ata0: devices=01
> > ata0: at 0x1f0 irq 14 on atapci0
> > ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1808
> > ata1: mask=03 ostat0=50 ostat2=00
> > ata1-master: ATAPI 14 eb
> > ata1-slave: ATAPI 00 00
> > ata1: mask=03 stat0=00 stat1=00
> > ata1: devices=04
> > ata1: at 0x170 irq 15 on atapci0
> > pci0: <serial bus, USB> at device 31.2 (no driver attached)
> > pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> > pci0: <serial bus, USB> at device 31.4 (no driver attached)
> > pcm0: <Intel 82801BA (ICH2)> port 0x1840-0x187f,0x1c00-0x1cff irq 5 at
> > device 31.5 on pci0
> > pcm0: ac97 codec id 0x83847600 (SigmaTel STAC9700/9783/9784)
> > pcm0: ac97 codec features 18 bit DAC, 18 bit ADC, 5 bit master volume,
> > SigmaTel 3D Enhancement
> > pcm0: sndbuf_setmap 71000, 4000; 0xd1dca000 -> 71000
> > pcm0: sndbuf_setmap 8e000, 4000; 0xd1dd7000 -> 8e000
> > pcm0: measured ac97 link rate at 29293 Hz
> > ata: ata0 already exists; skipping it
> > ata: ata1 already exists; skipping it
> > Trying Read_Port at 203
> > Trying Read_Port at 243
> > Trying Read_Port at 283
> > Trying Read_Port at 2c3
> > Trying Read_Port at 303
> > Trying Read_Port at 343
> > Trying Read_Port at 383
> > Trying Read_Port at 3c3
> > sc: sc0 already exists; skipping it
> > vga: vga0 already exists; skipping it
> > isa_probe_children: disabling PnP devices
> > isa_probe_children: probing non-PnP devices
> > orm0: <Option ROMs> at iomem
> 0xd4000-0xd7fff,0xd0000-0xd3fff,0xc0000-0xcbfff
> > on isa0
> > adv0 failed to probe on isa0
> > aha0 failed to probe on isa0
> > aic0 failed to probe on isa0
> > atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
> > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> > atkbd: the current kbd controller command byte 0047
> > atkbd: keyboard ID 0x41ab (2)
> > kbd0 at atkbd0
> > kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
> > psm0: current command byte:0047
> > psm0: <PS/2 Mouse> irq 12 on atkbdc0
> > psm0: model IntelliMouse, device ID 3-00, 3 buttons
> > psm0: config:00000000, flags:00000000, packet size:4
> > psm0: syncmask:08, syncbits:08
> > bt0 failed to probe on isa0
> > cs0 failed to probe at port 0x300 on isa0
> > ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
> > fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port
> > 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
> > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > fe0 failed to probe at port 0x300 on isa0
> > ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
> > le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
> > lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
> > pmtimer0 on isa0
> > ppc0: parallel port found at 0x378
> > ppc0: using extended I/O port range
> > ppc0: ECP SPP ECP+EPP SPP
> > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/8 bytes threshold
> > plip0: <PLIP network interface> on ppbus0
> > bpf: lp0 attached
> > lpt0: <Printer> on ppbus0
> > lpt0: Interrupt-driven port
> > sc0: <System console> at flags 0x100 on isa0
> > sc0: VGA <16 virtual consoles, flags=0x300>
> > sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> > sio0: irq maps: 0x1 0x11 0x1 0x1
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 16550A
> > sio1: configured irq 3 not in bitmap of probed irqs 0
> > sio1: port may not be enabled
> > sio1: irq maps: 0x1 0x1 0x1 0x1
> > sio1: probe failed test(s): 0 1 2 4 6 7 9
> > sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> > sio2: not probed (disabled)
> > sio3: not probed (disabled)
> > sn0 failed to probe at port 0x300 irq 10 on isa0
> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
> > fb0: vga0, vga, type:VGA (5), flags:0x700ff
> > fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> > fb0: init mode:24, bios mode:3, current mode:24
> > fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> > VGA parameters upon power-up
> > 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
> > bf 1f 00 4f 0d 0e 00 00 06 40 9c 8e 8f 28 1f 96
> > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> > VGA parameters in BIOS for mode 24
> > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> > EGA/VGA parameters to be used for mode 24
> > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> > vt0 failed to probe on isa0
> > isa_probe_children: probing PnP devices
> > BIOS Geometries:
> >  0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
> >  0 accounted for
> > Device configuration finished.
> > procfs registered
> > Timecounters tick every 10.000 msec
> > bpf: lo0 attached
> > ad0: success setting UDMA5 on Intel chip
> > Creating DISK ad0
> > ar: FreeBSD check1 failed
> > ad0: <HITACHI_DK23CA-20/00H1A0G1> ATA-5 disk at ata0-master
> > ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
> > ad0: 16 secs/int, 1 depth queue, UDMA100
> > ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
> > ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
> > ata1-master: success setting PIO4 on generic chip
> > acd0: <SAMSUNG CD-ROM SN-124/N001> CDROM drive at ata1 as master
> > acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
> > acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
> > acd0: Writes:
> > acd0: Audio: play, 255 volume levels
> > acd0: Mechanism: ejectable tray, unlocked
> > acd0: Medium: CD-ROM 120mm audio disc
> > Mounting root from ufs:/dev/ad0s2a
> > ad0s1: type 0x6, start 63, end = 273104, size 273042 : OK
> > ad0s2: type 0xa5, start 273105, end = 19663559, size 19390455 : OK
> > ad0s3: type 0xf, start 19663560, end = 39054014, size 19390455
> > ad0s3: C/H/S start 1023/0/1 (16434495) != start 19663560: invalid
> > ad0s5: type 0x7, start 19663623, end = 39054014, size 19390392
> > ad0s5: C/H/S start 1023/1/1 (16434558) != start 19663623: invalid
> > start_init: trying /sbin/init
> > Entropy harvesting:
> >  interrupts
> >  ethernet
> >  point_to_point
> > .
> > swapon: adding /dev/ad0s2b as swap device
> > swapon: adding /dev/ad0s2e as swap device
> > Automatic boot in progress...
> > /dev/ad0s2a: FILESYSTEM CLEAN; SKIPPING CHECKS
> > /dev/ad0s2a: clean, 2846783 free (20743 frags, 353255 blocks, 0.5%
> > fragmentation)
> > Doing initial network setup:
> >  host.conf
> >  hostname
> > .
> > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> >  inet 127.0.0.1 netmask 0xff000000
> > route:
> > writing to routing socket
> > :
> > Network is unreachable
> > add net default: gateway 192.168.40.254: Network is unreachable
> > Additional routing options:
> > .
> > Routing daemons:
> > .
> > Additional daemons:
> >  syslogd
> > May  4 12:59:53 jupiter syslogd: kernel boot file is /boot/kernel/kernel
> > .
> > Doing additional network setup:
> > .
> > Starting final network daemons:
> > .
> > ELF ldconfig path: /usr/lib /usr/lib/compat /usr/X11R6/lib
/usr/local/lib
> > a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
> /usr/X11R6/lib/aout
> > Starting standard daemons:
> >  cron
> >  sshd
> >  sendmail-submit
> >  sendmail-clientmqueue
> > .
> > Initial rc.i386 initialization:
> > .
> > Configuring syscons:
> >  blanktime
> > .
> > Additional ABI support:
> > .
> > Local package initialization:
> > .
> > Additional TCP options:
> > .
> > Starting background filesystem checks
> >
> > Sat May  4 12:59:55 EST 2002
> > May  4 13:00:03 jupiter login: ROOT LOGIN (root) ON ttyv1
> > link_elf: symbol gd_curproc undefined
> > link_elf: symbol gd_curproc undefined
> > link_elf: symbol gd_curproc undefined
> > link_elf: symbol gd_curproc undefined
> > link_elf: symbol gd_curproc undefined
> > fd0: autoselected 1440 KB medium
> > WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> > WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> > fd0: autoselected 1440 KB medium
> > WARNING: R/W mount of /mnt denied.  Filesystem is not clean - run fsck
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > pcib1: device pccard0 requested unsupported memory range
> > 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> > pcib1: device pccard0 requested decoded memory range
0x84000000-0xffffffff
> > pccard0: CIS version PCCARD 2.0 or 2.1
> > pccard0: CIS info: 3Com Corporation, 3C589D, TP/BNC LAN Card Ver. 2a,
> 000002
> > pccard0: Manufacturer code 0x101, product 0x589
> > pccard0: function 0: network adapter, ccr addr 10000 mask 3
> > pccard0: function 0, config table entry 1: I/O card; irq mask ffff;
iomask
> > 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
> > pccard0: function 0, config table entry 3: I/O card; irq mask ffff;
iomask
> > 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
> > pcib1: device pccard0 requested decoded I/O range 0x100-0xffffffff
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > pcib1: device pccard0 requested unsupported memory range
> > 0x84000000-0xffffffff (decoding 0xfff00000-0xfffff, 0xfff00000-0xfffff)
> > pcib1: device pccard0 requested decoded memory range
0x84000000-0xffffffff
> > ep0: <3Com 3c589 10Mbps Ethernet> at port 0x100-0x10f irq 9 function 0
> > config 1 on pccard0
> > pcib1: device ep0 requested decoded I/O range 0x100-0x10f
> > pcib1: device pccard0 requested decoded I/O range 0x100-0x10f
> > pcib1: device ep0 requested decoded I/O range 0x100-0x10f
> > ep0: Ethernet address 00:60:97:89:94:37
> > bpf: ep0 attached
> > May  4 13:35:25 jupiter login: ROOT LOGIN (root) ON ttyv2
> >
> >
> >
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > Product version: 5.0
> > Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G |
1.03
> |
> > Manufacturer ID: 0501030181
> > Functions: Network Adaptor, Multi-Functioned
> > Function Extension: 04060010a4d1c890
> > Function Extension: 0102
> > Function Extension: 0280969800
> > Function Extension: 0200e1f505
> > Function Extension: 0301
> > Function Extension: 0303
> > Function Extension: 0501
> > cardbus0: Invalid BAR number: 27(06)
> > CIS reading done
> > start (84000000) < sc->membase (fff00000)
> > end (ffffffff) > sc->memlimit (fffff)
> > pcib1: device cardbus0 requested unsupported memory range
> > 0x84000000-0xffffffff
> > (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> > pcib1: device cardbus0 requested decoded memory range
> 0x84000000-0xffffffff
> > end (0x840217f) > sc->memlimit (fffff)
> > pcib1: device cardbus0 requested unsupported memory range
> > 0x84002000-0x8400217f
> > (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> > pcib1: device cardbus0 requested decoded memory range
> 0x84002000-0x8400217f
> > end (8400217f) > sc->memlimit (fffff)
> > pcib1: device cardbus0 requested unsupported memory range
> > 0x84002000-0x8400217f
> > (decoding 0xfff00000-0xfffff,0xfff00000-0xfffff)
> > pcib1: device cardbus0 requested decoded memory range
> 0x84002000-0x8400217f
> > pcib1: device cardbus0 requested decoded I/O range 0x1000-0xffffffff
> > pcib1: device cardbus0 requested decoded I/O range 0x1000-0x107f
> > dc0: <Xircom X3201 10/100BaseTX> port 0x1000-0x107f mem
> > 0x84002000-0x840020ff,0x84002100-0x8400217f irq 9 at device 0.0 on
> cardbus0
> > pcib1: device dc0 requested decoded I/O range 0x1000-0x107f
> > <... hardlock occurs here ...>
> >
> >
> >
> > #
> > # NEWCARD -- efforts at porting newconfig pccard/cardbus code to newbus
> > #
> >
> > machine  i386
> > cpu  I686_CPU
> > ident  JUPITER
> > maxusers 0
> >
> > makeoptions DEBUG=-g  #Build kernel with gdb(1) debug symbols
> >
> > options  INET   #InterNETworking
> > options  FFS   #Berkeley Fast Filesystem
> > options  SOFTUPDATES  #Enable FFS soft updates support
> > options  UFS_DIRHASH  #Improve performance on big directories
> > options  NFSCLIENT  #Network Filesystem Client
> > options  MSDOSFS   #MSDOS Filesystem
> > options  CD9660   #ISO 9660 Filesystem
> > options  PROCFS   #Process filesystem (requires PSEUDOFS)
> > options  PSEUDOFS  #Pseudo-filesystem framework
> > options  COMPAT_43  #Compatible with BSD 4.3 [KEEP THIS!]
> > options  KTRACE   #ktrace(1) support
> > options  SYSVSHM   #SYSV-style shared memory
> > options  SYSVMSG   #SYSV-style message queues
> > options  SYSVSEM   #SYSV-style semaphores
> > options  P1003_1B  #Posix P1003_1B real-time extensions
> > options  _KPOSIX_PRIORITY_SCHEDULING
> > options  KBD_INSTALL_CDEV # install a CDEV entry in /dev
> >
> > # Debugging for use in -current
> > options  DDB   #Enable the kernel debugger
> > options  INVARIANTS  #Enable calls of extra sanity checking
> > options  INVARIANT_SUPPORT #Extra sanity checks of internal structures,
> > required by INVARIANTS
> > options  WITNESS   #Enable mutex checks to detects deadlocks and cycles
> > options  WITNESS_SKIPSPIN #Don't run witness on spinlocks for speed
> >
> > device  isa
> > device  pci
> > #options  PCI_ENABLE_IO_MODES # Enable pci resources left off by a "lazy
> > BIOS"
> > options  PCI_ALLOW_UNSUPPORTED_IO_RANGE
> >
> > # AGP GART support
> > device  agp
> > options  VESA
> >
> > # Floppy drives
> > device  fdc
> >
> > # ATA and ATAPI devices
> > device  ata
> > device  atadisk   # ATA disk drives
> > device  atapicd   # ATAPI CDROM drives
> >
> > # atkbdc0 controls both the keyboard and the PS/2 mouse
> > device  atkbdc 1 # At keyboard controller
> > device  atkbd  # at keyboard
> > device  psm  # psm mouse
> >
> > device  vga  # VGA screen
> >
> > # splash screen/screen saver
> > device  splash
> >
> > # syscons is the default console driver, resembling an SCO console
> > device  sc 1
> >
> > # Floating point support - do not disable.
> > device  npx
> >
> > # Power management support (see NOTES for more options)
> > device  apm
> > # Add suspend/resume support for the i8254.
> > device  pmtimer
> >
> > # Pcmcia and cardbus bridge support
> > device  pccbb   # cardbus (yenta) bridge
> > device  pccard
> > device  cardbus
> > #device  card
> > #device  pcic
> >
> > # Serial (COM) ports
> > device  sio  # 8250, 16[45]50 based serial ports
> >
> > # Parallel port
> > device  ppc
> > device  ppbus  # Parallel port bus (required)
> > device  lpt  # Printer
> > device  plip  # TCP/IP over parallel
> >
> > # PCI Ethernet NICs that use the common MII bus controller code.
> > # NOTE: Be sure to keep the 'device miibus' line in order to use these
> NICs!
> > device  miibus  # MII bus support
> > device  dc  # DEC/Intel 21143 and various workalikes
> >
> > # ISA Ethernet NICs.  pccard nics included.
> > device  ep  # Etherlink III based cards
> >
> > # Wireless NIC cards
> > device  wi  # WaveLAN/IEEE 802.11 wireless NICs.
> >
> > # Pseudo devices - the number indicates how many units to allocate.
> > device  random  # Entropy device
> > device  loop  # Network loopback
> > device  ether  # Ethernet support
> > device  tun  # Packet tunnel.
> > device  pty  # Pseudo-ttys (telnet etc)
> > device  md  # Memory "disks"
> > device  gif  # IPv6 and IPv4 tunneling
> >
> > # The `bpf' device enables the Berkeley Packet Filter.
> > # Be aware of the administrative consequences of enabling this!
> > device  bpf  # Berkeley packet filter
> >
> > device  pcm
> >
> >
> >
> >
> >
> > To Unsubscribe: send mail to majordomo@FreeBSD.org
> > with "unsubscribe freebsd-mobile" in the body of the message
> >
> >
>
>
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-mobile" in the body of the message
>
>



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?002801c1f503$c6db1c80$0128a8c0>