Date: Wed, 26 Apr 2000 20:02:47 +0200 From: Wilko Bulte <wkb@chello.nl> To: FreeBSD-alpha mailing list <freebsd-alpha@freebsd.org> Subject: trying to get DE203 (ISA) to work on Alpha Message-ID: <20000426200247.C1581@yedi.wbnet>
next in thread | raw e-mail | index | archive | help
Question: are ISA ethernet cards supposed to work on FreeBSD/alpha (4.0R)?
I have a DEC DE203 ISA card that I want to get to run on my Aspen Alpine
(EB64+) but I'm not having a whole lot of success. The kernel has been
built with:
# DE203
device le0 at isa? port 0x300 irq 5 iomem 0xd0000
But nothing shows in the probe messages during boot:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Fri Apr 7 10:48:12 CEST 2000
root@alpine.wbnet:/usr/src/sys/compile/ALPINE
EB64+
Alpha 21064A Evaluation Board 274 MHz, 274MHz
8192 byte page size, 1 processor.
CPU: EV45 (21064A) major=6 minor=2
OSF PAL rev: 0x100070002012d
real memory = 31473664 (30736K bytes)
Physical memory chunk(s):
0x0012c000 - 0x002fbfff, 1900544 bytes (232 pages)
0x005e2000 - 0x01f0dfff, 26394624 bytes (3222 pages)
avail memory = 27123712 (26488K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00005e0000.
found-> vendor=0x1000, dev=0x0001, revid=0x01
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=7
map[10]: type 1, range 32, base 00010000, size 8
map[14]: type 1, range 32, base 81010000, size 8
found-> vendor=0x5333, dev=0x8811, revid=0x54
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=1
map[10]: type 1, range 32, base 84000000, size 26
found-> vendor=0x8086, dev=0x0484, revid=0x03
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
ncr0: <ncr 53c810 fast10 scsi> port 0x10000-0x100ff mem
0x81010000-0x810100ff irq 7 at device 5.0 on pci0
BIOS values: SCNTL3:00 DMODE:00 DCNTL:01
CTEST3:00 CTEST4:00 CTEST5:00
ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr0: single-ended, open drain IRQ driver
ncr0: interrupting at APECS irq 7
ncr0: driver is using old-style compatability shims
pci0: <S3 Trio graphics accelerator> (vendor=0x5333, dev=0x8811) at 7.0 irq
1
isab0: <Intel 82378ZB PCI to ISA bridge> at device 8.0 on pci0
Bus Modes: Resource Lock,
Mouse function enabled
Keyboard controller: 60h,62h,64h,66h
RTC: 70h-77h
Configuration RAM: 0C00h,0800h-08FFh
Port 92: enabled
isa0: <ISA bus> on isab0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000, port:0x60-0x6f
atkbd0: interrupting at ISA irq 1
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 275008104 Hz (firmware 274725274 Hz)
sio0: irq maps: 0x41 0x50 0x40 0x40
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: reserved for low-level i/o
isa_probe_children: probing PnP devices
Timecounter "alpha" frequency 275008104 Hz
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: stf0 attached
bpf: faith0 attached
Waiting 5 seconds for SCSI devices to settle
ncr0: restart (scsi reset).
ACTUAL values:SCNTL3:03 DMODE:c8 DCNTL:01
CTEST3:00 CTEST4:08 CTEST5:00
(probe4:ncr0:0:4:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe4:ncr0:0:4:0): ILLEGAL REQUEST asc:24,0
(probe4:ncr0:0:4:0): Invalid field in CDB sks:c8,1
Creating DISK da0
Creating DISK cd0
pass0 at ncr0 bus 0 target 0 lun 0
pass0: <QUANTUM FIREBALL1280S 630A> Fixed Direct Access SCSI-2 device
pass0: Serial Number 122608527398
pass0: 10.000MB/s transfers (10.000MHz, offset 8)
pass1 at ncr0 bus 0 target 4 lun 0
pass1: <TOSHIBA CD-ROM XM-5301TA 1895> Removable CD-ROM SCSI-2 device
pass1: 4.237MB/s transfers (4.237MHz, offset 8)
da0 at ncr0 bus 0 target 0 lun 0
da0: <QUANTUM FIREBALL1280S 630A> Fixed Direct Access SCSI-2 device
da0: Serial Number 122608527398
da0: 10.000MB/s transfers (10.000MHz, offset 8)
da0: 1222MB (2503872 512 byte sectors: 255H 63S/T 155C)
Mounting root from ufs:/dev/da0a
(cd0:ncr0:0:4:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ncr0:0:4:0): NOT READY asc:3a,0
(cd0:ncr0:0:4:0): Medium not present
cd0 at ncr0 bus 0 target 4 lun 0
cd0: <TOSHIBA CD-ROM XM-5301TA 1895> Removable CD-ROM SCSI-2 device
cd0: 4.237MB/s transfers (4.237MHz, offset 8)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0: invalid primary partition table: no magic
Related question: is SRM's isacfg used at all with FreeBSD?
Wilko (who until now always used PCI cards on his alpha machines..)
--
Wilko Bulte Powered by FreeBSD http://www.freebsd.org
http://www.tcja.nl
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000426200247.C1581>