Date: Fri, 8 Feb 2002 10:40:02 -0800 From: "Seamus Wassman" <sparhawk@ImLazy.net> To: <freebsd-alpha@freebsd.org> Subject: IDE interface on an AlphaServer 400 (Avanti) Message-ID: <LGEHLOFOAAMOLELMOAJJIECBCAAA.sparhawk@ImLazy.net>
next in thread | raw e-mail | index | archive | help
I am trying to get the IDE interface on my AlphaServer 400 to detect in 4.5
stable (cvsed as of about 1 week ago).
I have put the following in my kernel config file:
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
and have also tried just:
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
Both fail to detect the presence of an IDE controller.
Below is a complete dmesg output:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #5: Fri Feb 1 02:04:51 PST 2002
root@WinterMute.ImLazy.net:/usr/src/sys/compile/WINTERMUTE
AlphaStation 200/400 ("Avanti")
AlphaServer 400 4/233, 233MHz
8192 byte page size, 1 processor.
CPU: EV45 (21064A) major=6 minor=0
OSF PAL rev: 0x100000002012e
real memory = 132169728 (129072K bytes)
avail memory = 122126336 (119264K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00007d8000.
md0: Malloc disk
pci0: <PCI bus> on pcib0
sym0: <810> port 0x10100-0x101ff mem 0x82030400-0x820304ff irq 11 at device
6.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: interrupting at ISA irq 11
isab0: <Intel 82378ZB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <S3 ViRGE DX/GX graphics accelerator> at 11.0 irq 5
de0: <Digital 21040 Ethernet> port 0x10200-0x1027f mem 0x82030500-0x8203057f
irq 9 at device 12.0 on pci0
de0: interrupting at ISA irq 9
de0: DEC 21040 [10Mb/s] pass 2.3
de0: address 08:00:2b:e6:b5:2b
dc0: <ADMtek AN985 10/100BaseTX> port 0x10000-0x100ff mem
0x82030000-0x820303ff irq 10 at device 13.0 on pci0
dc0: interrupting at ISA irq 10
dc0: Ethernet address: 00:03:6d:1d:a3:db
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROM> at iomem 0xec000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd0: interrupting at ISA irq 1
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A
sio0: interrupting at ISA irq 4
sio1: reserved for low-level i/o
ppc0: <Parallel port> at port 0x3bc-0x3bf irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: cannot reserve interrupt, failed.
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
ppc0: interrupting at ISA irq 7
Timecounter "alpha" frequency 233333772 Hz
IP Filter: v3.4.20 initialized. Default = pass all, Logging = disabled
Waiting 15 seconds for SCSI devices to settle
de0: enabling 10baseT port
Mounting root from ufs:/dev/da0a
da0 at sym0 bus 0 target 0 lun 0
da0: <DEC RZ29B (C) DEC 0014> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C)
da1 at sym0 bus 0 target 1 lun 0
da1: <DEC RZ29B (C) DEC 0014> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da1: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C)
cd0 at sym0 bus 0 target 2 lun 0
cd0: <TOSHIBA CD-ROM XM-5301TA 1645> Removable CD-ROM SCSI-2 device
cd0: 4.237MB/s transfers (4.237MHz, offset 8)
cd0: Attempt to query device size failed: NOT READY, Medium not present
de0: promiscuous mode enabled
pid 159 (ntop), uid 65534: exited on signal 11
de0: promiscuous mode disabled
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?LGEHLOFOAAMOLELMOAJJIECBCAAA.sparhawk>