Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 4 Oct 2015 22:50:38 +0000 (UTC)
From:      Sean Bruno <sbruno@FreeBSD.org>
To:        src-committers@freebsd.org, svn-src-all@freebsd.org, svn-src-head@freebsd.org
Subject:   svn commit: r288672 - head/sys/mips/conf
Message-ID:  <201510042250.t94Mocjq063208@repo.freebsd.org>

next in thread | raw e-mail | index | archive | help
Author: sbruno
Date: Sun Oct  4 22:50:37 2015
New Revision: 288672
URL: https://svnweb.freebsd.org/changeset/base/288672

Log:
  Set correct argemdio addr, comment out arge1 as its not physically
  connected to anything.  Move a couple of devices out of the kernel
  and into modules.

Modified:
  head/sys/mips/conf/WZR-300HP
  head/sys/mips/conf/WZR-300HP.hints

Modified: head/sys/mips/conf/WZR-300HP
==============================================================================
--- head/sys/mips/conf/WZR-300HP	Sun Oct  4 21:16:45 2015	(r288671)
+++ head/sys/mips/conf/WZR-300HP	Sun Oct  4 22:50:37 2015	(r288672)
@@ -28,9 +28,6 @@ device		geom_uncompress	# compressed in-
 
 options 	ROOTDEVNAME=\"ufs:/dev/map/rootfs.uncompress\"
 
-# options 	MD_ROOT
-# options 	MD_ROOT_SIZE="6144"
-
 options 	AR71XX_ATH_EEPROM	# Fetch EEPROM/PCI config from flash
 options 	ATH_EEPROM_FIRMWARE	# Use EEPROM from flash
 device		firmware		# Used by the above
@@ -42,10 +39,11 @@ device          miiproxy                
 device          etherswitch
 device          arswitch
 
-# Enable GPIO
-device         gpio
-device         gpioled
-
 # hwpmc
 device		hwpmc_mips24k
 device		hwpmc
+
+# load these via modules, shrink kernel
+nodevice	if_bridge
+nodevice	bridgestp
+nodevice	random

Modified: head/sys/mips/conf/WZR-300HP.hints
==============================================================================
--- head/sys/mips/conf/WZR-300HP.hints	Sun Oct  4 21:16:45 2015	(r288671)
+++ head/sys/mips/conf/WZR-300HP.hints	Sun Oct  4 22:50:37 2015	(r288672)
@@ -5,11 +5,11 @@
 
 # arge1 MDIO bus
 hint.argemdio.0.at="nexus0"
-hint.argemdio.0.maddr=0x1a000000
+hint.argemdio.0.maddr=0x19000000
 hint.argemdio.0.msize=0x1000
 hint.argemdio.0.order=0
 
-hint.arge.0.phymask=0x0
+hint.arge.0.phymask=0x1
 hint.arge.0.media=1000
 hint.arge.0.fduplex=1
 hint.arge.0.eeprommac=0x1f05120c
@@ -17,9 +17,9 @@ hint.arge.0.mdio=mdioproxy1     # .. off
 
 
 # arge1: nail to 1000/full, RMII - connected to the switch
-hint.arge.1.media=1000          # Map to 1000/full
-hint.arge.1.fduplex=1           #
-hint.arge.1.phymask=0x0         # no directly mapped PHYs
+#hint.arge.1.media=1000          # Map to 1000/full
+#hint.arge.1.fduplex=1           #
+#hint.arge.1.phymask=0x0         # no directly mapped PHYs
 
 #
 # AR7240 switch config
@@ -28,7 +28,7 @@ hint.arswitch.0.at="mdio0"
 hint.arswitch.0.is_7240=1       # We need to be explicitly told this
 hint.arswitch.0.numphys=4       # 4 active switch PHYs (PHY 0 -> 3)
 hint.arswitch.0.phy4cpu=1       # Yes, PHY 4 == dedicated PHY
-hint.arswitch.0.is_rgmii=0      # No, not RGMII
+hint.arswitch.0.is_rgmii=1      # No, not RGMII
 hint.arswitch.0.is_gmii=0       # No, not GMII
 
 # ath0 - slot 0



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201510042250.t94Mocjq063208>