Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 30 Jun 2006 11:31:12 +0200
From:      Bohuslav Plucinsky <bohuslav.plucinsky@gtsnextra.sk>
To:        freebsd-net@freebsd.org, bugs@freebsd.org
Cc:        mlaier@freebsd.org
Subject:   Re: Xorp and CARP on FreeBSD
Message-ID:  <20060630093112.GA24299@gtsnextra.sk>
In-Reply-To: <20060609113221.GD25880@gtsnextra.sk>
References:  <20060609113221.GD25880@gtsnextra.sk>

next in thread | previous in thread | raw e-mail | index | archive | help
Hello,

here is a reply from one of the XORP developers, Pavlin Radoslavov. What is your 
opinion to this problem ?

Thanks,
Bohus

----- Forwarded message from Pavlin Radoslavov <pavlin@icir.org> -----

> To: bohuslav.plucinsky@gtsnextra.sk
> cc: Pavlin Radoslavov <pavlin@icir.org>, feedback@xorp.org
> Subject: Re: [Xorp-feedback] Xorp and CARP on FreeBSD 
> Date: Thu, 29 Jun 2006 15:54:06 -0700
> From: Pavlin Radoslavov <pavlin@icir.org>
> 
> > On Fri, Jun 09, 2006 at 09:46:36AM -0700, Pavlin Radoslavov wrote:
> > > > I've two FreeBSD 6.1-RELEASE routers (R1, R2)  with CARP configured 
> > > > and it was working OK untill I've installed Xorp and tried to configure
> > > > multicast PIM-SM. After that the CARP has stoped working. I've found 
> > > > out by the tcpdump that after Xorp is started the source IP address 
> > > > of CARP packets is changed to IP address used as register_vif in Xorp:
> > > 
> > > Do you get the same error if you configure only the "interfaces"
> > > section in the XORP config. 
> > 
> > No, the problem occures, only when the plumbing section is present.
> > 
> > > Also, is any of the IP address changed (by CARP) while XORP is running?
> > 
> > No. There are the CARP virtual interfaces created befor XORP is started.
> > CARP dosn't change any IP address, but XORP changes source IP address
> > of multicast CARP packets. When I stop XORP the IP address is retutned
> > to original IP address.
> 
> Thank you for the info.
> I did some investigation (FreeBSD-6.1) and I was able to see the
> the problem: VRRPv2 Advertisement messages with the wrong source
> address.
> 
> For the record, this is what I did (on a single machine):
> 
> =====================================
> ifconfig vlan97 create
> ifconfig vlan97 inet 192.168.100.2 netmask 255.255.255.0 vlan 97 vlandev xl0
> ifconfig vlan71 create
> ifconfig vlan71 inet 10.122.25.66 netmask 255.255.255.224 vlan 71 vlandev xl0
> ifconfig carp97 create
> ifconfig carp97 vhid 1 pass foofoo1 192.168.100.1/24
> ifconfig carp71 create
> ifconfig carp71 vhid 2 pass foofoo2 10.122.25.64/27
> =====================================
> 
> Then I started XORP with the configuration file included at the end
> of this email. Basically, the important thing in that configuration
> file is that inside the MFEA I enabled only the vlan71 interface.
> 
> Indeed, by running tcpdump I was able to see that the VRRPv2
> Advertisement messages sent over vlan97 changed their source address
> to be same ass the source address of vlan71:
> 
> =====================================
> root@carp[5] tcpdump -n -i vlan97 proto 112
> tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
> listening on vlan97, link-type EN10MB (Ethernet), capture size 96 bytes
> 15:38:04.614085 IP 192.168.100.2 > 224.0.0.18: VRRPv2, Advertisement, vrid 1, prio 0, authtype none, intvl 1s, length 36
> 15:38:05.615058 IP 192.168.100.2 > 224.0.0.18: VRRPv2, Advertisement, vrid 1, prio 0, authtype none, intvl 1s, length 36
> ...
> 15:38:22.635132 IP 10.122.25.66 > 224.0.0.18: VRRPv2, Advertisement, vrid 1, prio 0, authtype none, intvl 1s, length 36
> 15:38:23.636107 IP 10.122.25.66 > 224.0.0.18: VRRPv2, Advertisement, vrid 1, prio 0, authtype none, intvl 1s, length 36
> =====================================
> 
> After some investigation, I was able to trace the problem to the
> setsockopt(_mrouter_socket, IPPROTO_IP, MRT_ADD_VIF, ...) system
> call. In fact, I was able to reproduce the problem with other
> multicast routing implementations: mrouted and pimd which obviously
> also use the same setsockopt().
> After some further investigation, it seems to happen only when
> running CARP over vlan interfaces, but I haven't investigated this
> in greater details. At least, it didn't happen when I enabled in MFEA
> the physical xl0 network interface (also running CARP).
> 
> Hence, I belive the problem is in the FreeBSD kernel, and happens
> when we have 2+ vlan interfaces configured to run CARP and one of
> them is also configured for multicast routing.
> 
> You might want to contact the FreeBSD folks about that, because the
> problem is not XORP-specific.
> 
> Please let us know how it goes.
> 
> Thanks,
> Pavlin
> 
> 
> =====================================
> interfaces {
>     interface vlan97 {
>         description: "DMZ"
>         disable: false
>         default-system-config
>     }
>     interface vlan71 {
>         description: "intranet"
>         disable: false
>         default-system-config
>     }
> }
> 
>   fea {
>     unicast-forwarding4 {
>         disable: false
>     }
>   }
> 
>  plumbing {
>     mfea4 {
>         disable: false
>         interface vlan71 {
>             vif vlan71 {
>                 disable: false
>             }
>         }
> /*
>         interface vlan97 {
>             vif vlan97 {
>                 disable: false
>             }
>         }
> */
> /*
>         interface register_vif {
>             vif register_vif {
>                 Note: this vif should be always enabled
>                 disable: false
>             }
>         }
> */
>         traceoptions {
>             flag all {
>                 disable: false
>             }
>         }
>     }
> }
> =====================================
> 
> 

----- End forwarded message -----



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060630093112.GA24299>