Date: Mon, 17 Jun 2002 17:47:07 +0900 From: Hiroharu Tamaru <tamaru@myn.rcast.u-tokyo.ac.jp> To: freebsd-hardware@freebsd.org Subject: 3ware Escalade 7810 with old M/B: parity error Message-ID: <sa68z5e8f78.wl@gin.myn.rcast.u-tokyo.ac.jp>
next in thread | raw e-mail | index | archive | help
--Multipart_Mon_Jun_17_17:46:15_2002-1
Content-Type: text/plain; charset=US-ASCII
Hi,
I am trying to setup 3ware Escalde 7810 with somewhat old mother
board. The M/B is ASUS P2B-DS, equipped with 440BX chipset and with
dual Pentium II (450MHz). It has 4 32bit PCI slots and 2 ISA slots.
The 4.5-RELEASE install floppies paniced on the way.
I tried netbooting with -STABLE kernel as of May 8,
and now it boots (using GENERIC kernel, or SMP enabled kernel)
but then the screen is full of error messages.
When I boot, I keep on getting
"PCI parity error: Reseat card, move card or buggy device present."
message a few times a second from the twe driver, but the RAID drives
seem to be working as far as I can see; things mounts fine, I can
read/write to the array. Write test shows some 20-30MB/s in single
drive JBOD mode using Western Digital ATA-100 disk.
I don't get any errors if I boot off a DOS floppy, or a DOS (not
windows..) partition _on the array_. And again files can be
read/written fine. But this may just be that they don't show errors
anyway..
If I plug this card into some newer M/B, things work fine without any
error messages. For this I tried 32bit slots and 64bit slots; they
both worked without any error messages. This is another dual CPU
(Athlone MP 1500+) machine, if that matters.
The 7810 hardware is the newer version without the recalled
deficiency, and the firmware on the card is the newer release of Rev
7.4. I downloaded the image and had flashed them on.
The BIOS on the M/B is most recent too; although it dates back as far
as 07/04/00 (Rev 1013 beta, or Rev 1012b).
The PCI slot used is chosen so that 7810 does not share irq with any
other device, but I even shuffled them arround many times, to double
check that they are not loose or improperly seated.
So, all that said, I am suspecting if this could be due to pluging a
64bit PCI card into an old 32bit only PCI M/B. Is there any way to
fix or work around this? or is this a REAL error that need a newer M/B?
dmesg is attached at the end.
Thanks in advance.
--
Hiroharu Tamaru.
--Multipart_Mon_Jun_17_17:46:15_2002-1
Content-Type: text/plain
Content-Disposition: attachment; filename="dmesg.boot"
Content-Transfer-Encoding: quoted-printable
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-PRERELEASE #0: Tue May 14 01:10:08 JST 2002
tamaru@myn.rcast.u-tokyo.ac.jp:/w/4src/src/sys/compile/TWE
Calibrating clock(s) ... TSC clock: 451002898 Hz, i8254 clock: 1193129 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (451.03-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x652 Stepping =3D 2
Features=3D0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory =3D 268423168 (262132K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00476000 - 0x0fff4fff, 263712768 bytes (64383 pages)
avail memory =3D 256962560 (250940K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
IOAPIC #0 intpin 16 -> irq 11
IOAPIC #0 intpin 17 -> irq 5
IOAPIC #0 intpin 19 -> irq 10
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00f9f10
bios32: Entry =3D 0xf0530 (c00f0530) Rev =3D 0 Len =3D 1
pcibios: PCI BIOS entry at 0x730
pnpbios: Found PnP BIOS data at 0xc00fd360
pnpbios: Entry =3D f0000:d390 Rev =3D 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 000f8190
Preloaded elf kernel "kernel.new" at 0xc044c000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000602c
pci_open(1a): mode1res=3D0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=3D060000] [hdr=3D00] is there (id=3D71908086)
Using $PIR table, 7 entries at 0xc00f0d20
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=3D0x8086, dev=3D0x7190, revid=3D0x02
class=3D06-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
map[10]: type 1, range 32, base e4000000, size 26
found-> vendor=3D0x8086, dev=3D0x7191, revid=3D0x02
class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
subordinatebus=3D1 secondarybus=3D1
found-> vendor=3D0x8086, dev=3D0x7110, revid=3D0x02
class=3D06-01-00, hdrtype=3D0x00, mfdev=3D1
subordinatebus=3D0 secondarybus=3D0
found-> vendor=3D0x8086, dev=3D0x7111, revid=3D0x01
class=3D01-01-80, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
map[20]: type 1, range 32, base 0000d800, size 4
found-> vendor=3D0x8086, dev=3D0x7112, revid=3D0x01
class=3D0c-03-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Dd, irq=3D10
map[20]: type 1, range 32, base 0000d400, size 5
found-> vendor=3D0x8086, dev=3D0x7113, revid=3D0x02
class=3D06-80-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
map[90]: type 1, range 32, base 0000e800, size 4
found-> vendor=3D0x9005, dev=3D0x001f, revid=3D0x00
class=3D01-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D10
map[10]: type 1, range 32, base 0000d000, size 8
map[14]: type 1, range 64, base e1000000, size 12
found-> vendor=3D0x13c1, dev=3D0x1001, revid=3D0x01
class=3D01-04-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D5
map[10]: type 1, range 32, base 0000b800, size 4
map[14]: type 1, range 32, base e0800000, size 4
map[18]: type 1, range 32, base e0000000, size 23
found-> vendor=3D0x8086, dev=3D0x1229, revid=3D0x08
class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D11
map[10]: type 1, range 32, base df800000, size 12
map[14]: type 1, range 32, base 0000b400, size 6
map[18]: type 1, range 32, base df000000, size 20
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=3D0x102b, dev=3D0x0521, revid=3D0x01
class=3D03-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D11
map[10]: type 1, range 32, base e3000000, size 24
map[14]: type 1, range 32, base e2000000, size 14
map[18]: type 1, range 32, base e1800000, size 23
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G200 AGP graphics accelerator> (vendor=3D0x102b, dev=3D0x=
0521) at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 on=
pci0
ata0: iobase=3D0x01f0 altiobase=3D0x03f6 bmaddr=3D0xd800
ata0: mask=3D03 ostat0=3D00 ostat2=3D00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=3D03 stat0=3D00 stat1=3D00
ata0: devices=3D00
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=3D0x0170 altiobase=3D0x0376 bmaddr=3D0xd808
ata1: mask=3D03 ostat0=3D00 ostat2=3D00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=3D03 stat0=3D00 stat1=3D00
ata1: devices=3D00
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 10 =
at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at de=
vice 4.3 on pci0
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xe10=
00000-0xe1000fff irq 10 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
using shared irq10.
aic7890/91: Ultra2 Wide Channel A, SCSI Id=3D7, 32/253 SCBs
twe0: <3ware Storage Controller> port 0xb800-0xb80f mem 0xe0000000-0xe07fff=
ff,0xe0800000-0xe080000f irq 5 at device 11.0 on pci0
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: AEN: <soft reset>
twe0: 8 ports, Firmware FE7X 1.04.00.024, BIOS BE7X 1.07.02.008
twe0: Monitor ME7X 1.01.00.034, PCB Rev3 , Achip V3.20 , Pchip V1.30 =
=20
twe0: port 0: WDC WD800AB-32BTA0 76319MB
twe0: port 1: WDC WD800AB-32BTA0 76319MB
twe0: port 2: WDC WD800AB-32BTA0 76319MB
twe0: port 5: WDC WD800AB-32BTA0 76319MB
twe0: port 6: WDC WD800AB-32BTA0 76319MB
twe0: port 7: WDC WD800AB-32BTA0 76319MB
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb400-0xb43f mem 0xdf000000-0=
xdf0fffff,0xdf800000-0xdf800fff irq 11 at device 12.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:90:27:c1:bf:5e
fxp0: PCI IDs: 8086 1229 8086 000c 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xcc000-0xccff=
f on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-51, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 5, 6, 7, 10, 11, 12, 14, 15, apic_imen: 0x00ff2=
305
BIOS Geometries:
0:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
1:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
2:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
3:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
4:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
5:03fffe3f 0..1023=3D1024 cylinders, 0..254=3D255 heads, 1..63=3D63 sectors
0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 6800c460, tty 6300109a, net 6700189a
bpf: sl0 attached
bpf: faith0 attached
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
twe0: PCI parity error: Reseat card, move card or buggy device present.twed=
0: <JBOD, Normal> on twe0
twed0: 76319MB (156301488 sectors)
Creating DISK twed0
twed1: <JBOD, Normal> on twe0
twed1: 76319MB (156301488 sectors)
Creating DISK twed1
twed2: <JBOD, Normal> on twe0
twed2: 76319MB (156301488 sectors)
Creating DISK twed2
twed3: <JBOD, Normal> on twe0
twed3: 76319MB (156301488 sectors)
Creating DISK twed3
twed4: <JBOD, Normal> on twe0
twed4: 76319MB (156301488 sectors)
Creating DISK twed4
twed5: <JBOD, Normal> on twe0
twed5: 76319MB (156301488 sectors)
Creating DISK twed5
twe0: command interrupt
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.twe0: PC=
I parity error: Reseat card, move card or buggy device present.twe0: PCI pa=
rity error: Reseat card, move card or buggy device present.twe0: PCI parity=
error: Reseat card, move card or buggy device present.twe0: PCI parity err=
or: Reseat card, move card or buggy device present.twe0: PCI parity error: =
Reseat card, move card or buggy device present.twe0: PCI parity error: Rese=
at card, move card or buggy device present.twe0: PCI parity error: Reseat c=
ard, move card or buggy device present.twe0: PCI parity error: Reseat card,=
move card or buggy device present.twe0: PCI parity error: Reseat card, mov=
e card or buggy device present.twe0: PCI parity error: Reseat card, move ca=
rd or buggy device present.twe0: PCI parity error: Reseat card, move card o=
r buggy device present.twe0: PCI parity error: Reseat card, move card or bu=
ggy device present.twe0: PCI parity error: Reseat card, move card or buggy =
device present.twe0: PCI parity error: Reseat card, move card or buggy devi=
ce present.twe0: PCI parity error: Reseat card, move card or buggy device p=
resent.twe0: PCI parity error: Reseat card, move card or buggy device prese=
nt.twe0: PCI parity error: Reseat card, move card or buggy device present.t=
we0: PCI parity error: Reseat card, move card or buggy device present.twe0:=
PCI parity error: Reseat card, move card or buggy device present.twe0: PCI=
parity error: Reseat card, move card or buggy device present.twe0: PCI par=
ity error: Reseat card, move card or buggy device present.twe0: PCI parity =
error: Reseat card, move card or buggy device present.twe0: PCI parity erro=
r: Reseat card, move card or buggy device present.twe0: PCI parity error: R=
eseat card, move card or buggy device present.twe0: PCI parity error: Resea=
t card, move card or buggy device present.twe0: PCI parity error: Reseat ca=
rd, move card or buggy device present.twe0: unexpected status bit(s) 800000=
<PCIPERR>
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.twe0: PC=
I parity error: Reseat card, move card or buggy device present.twe0: PCI pa=
rity error: Reseat card, move card or buggy device present.twe0: PCI parity=
error: Reseat card, move card or buggy device present.twe0: PCI parity err=
or: Reseat card, move card or buggy device present.twe0: PCI parity error: =
Reseat card, move card or buggy device present.twe0: PCI parity error: Rese=
at card, move card or buggy device present.twe0: PCI parity error: Reseat c=
ard, move card or buggy device present.twe0: PCI parity error: Reseat card,=
move card or buggy device present.twe0: PCI parity error: Reseat card, mov=
e card or buggy device present.twe0: PCI parity error: Reseat card, move ca=
rd or buggy device present.twe0: PCI parity error: Reseat card, move card o=
r buggy device present.twe0: PCI parity error: Reseat card, move card or bu=
ggy device present.twe0: PCI parity error: Reseat card, move card or buggy =
device present.twe0: PCI parity error: Reseat card, move card or buggy devi=
ce present.twe0: PCI parity error: Reseat card, move card or buggy device p=
resent.twe0: PCI parity error: Reseat card, move card or buggy device prese=
nt.twe0: PCI parity error: Reseat card, move card or buggy device present.t=
we0: PCI parity error: Reseat card, move card or buggy device present.twe0:=
PCI parity error: Reseat card, move card or buggy device present.twe0: PCI=
parity error: Reseat card, move card or buggy device present.twe0: PCI par=
ity error: Reseat card, move card or buggy device present.twe0: PCI parity =
error: Reseat card, move card or buggy device present.twe0: PCI parity erro=
r: Reseat card, move card or buggy device present.twe0: PCI parity error: R=
eseat card, move card or buggy device present.twe0: PCI parity error: Resea=
t card, move card or buggy device present.Mounting root from nfs:
NFS ROOT: 10.22.17.5:/w/proot
start_init: trying /sbin/init
twe0: unexpected status bit(s) 800000<PCIPERR>
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.twe0: PC=
I parity error: Reseat card, move card or buggy device present.twe0: PCI pa=
rity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.twe0: PC=
I parity error: Reseat card, move card or buggy device present.twe0: PCI pa=
rity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.twe0=
: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
twe0: PCI parity error: Reseat card, move card or buggy device present.
--Multipart_Mon_Jun_17_17:46:15_2002-1--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?sa68z5e8f78.wl>