Date: Sun, 14 Apr 1996 17:14:41 +0100 (WET DST) From: Paulo Menezes <paulo@centauro.isr.uc.pt> To: current@freebsd.org Subject: Another problem with Adaptec 2940 and S3TRIO64 Message-ID: <Pine.SUN.3.91.960414170326.14069C-100000@centauro>
next in thread | raw e-mail | index | archive | help
Hi,
Yesterday I installed 2.1R in a HP Vectra VL 5/100.
I have noticed that the system hangs during periods of heavy disk
activity, with or without X86_S3 running. After the second hang I
rebooted the machine and started to compile knews just to see if there
was any message and .....
ahc0: target 0, lun 0 (sd0) timed out
sd0(ahc0:0:0): BUS DEVICE RESET message queued.
sd0(ahc0:0:0): ABORTED COMMAND asc:4e,0 Overlapped commands attempted
, retries:4
Can anyone tell me if this is related with my new hardware :-( ?
Thanks
Paulo
======================================================
FreeBSD 2.1.0-RELEASE #0: Sun Apr 14 03:55:07 1996
root@ener1000.dee.uc.pt:/usr/src/sys/compile/LOCAL
CPU: 99-MHz Pentium 735\\90 or 815\\100 (Pentium-class CPU)
Origin = "GenuineIntel" Id = 0x525 Stepping=5
Features=0x1bf<FPU,VME,PSE,MCE,CX8,APIC>
real memory = 16777216 (16384K bytes)
avail memory = 14827520 (14480K bytes)
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x280
ed1 at 0x300-0x31f irq 3 on isa
ed1: address 00:80:c8:2b:86:be, type NE2000 (16 bit)
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1: disabled, not probed.
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
mse0: wrong signature ff
mse0 not found at 0x23c
psm0 at 0x60-0x63 irq 12 on motherboard
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
wdc0 not found at 0x1f0
wdc1 not found at 0x170
bt0 not found at 0x330
uha0 not found at 0x330
ahc1 not found
ahb0 not found
aha0 not found at 0x330
aic0 not found at 0x340
nca0 not found at 0x1f88
nca1 not found at 0x350
sea0 not found
wt0 not probed due to I/O address conflict with ed1 at 0x300
mcd0 not probed due to I/O address conflict with ed1 at 0x300
mcd1: timeout getting status
mcd1 not found at 0x340
matcdc0 not found at 0x230
scd0 not found at 0x230
ep0 not probed due to I/O address conflict with ed1 at 0x300
npx0 on motherboard
npx0: INT 16 interface
pcibus_setup(1): mode1res=0x80000000 (0x80000000), mode2res=0xff (0x0e)
pcibus_setup(2): mode1res=0x80000000 (0x80000000)
pcibus_check: device 0 is there (id=122d8086)
Probing for devices on the PCI bus:
configuration mode 1 allows 32 devices.
chip0 <Intel 82437 (Triton)> rev 2 on pci0:0
ahc0 <Adaptec 2940 SCSI host adapter> rev 3 int a irq 9 on pci0:6
mapreg[10] type=1 addr=0000fc00 size=0100.
mapreg[14] type=0 addr=fedff000 size=1000.
ahc0: reading board settings
ahc0: Reading SEEPROM...done.
ahc0: 2940 Single Channel, SCSI Id=7, aic7870, 255 SCBs
ahc0: Downloading Sequencer Program...Done
ahc0: Probing channel A
ahc0 waiting for scsi devices to settle
ahc0: target 0 synchronous at 10.0MB/s, offset = 0xf
(ahc0:0:0): "MICROP 4221-09SC21020AV TN05" type 0 fixed SCSI 2
sd0(ahc0:0:0): Direct-Access 1955MB (4004219 512 byte sectors)
sd0(ahc0:0:0): with 4049 cyls, 9 heads, and an average 109 sectors/track
vga0 <VGA-compatible display device> rev 0 int a irq 255 on pci0:13
mapreg[10] type=0 addr=fe000000 size=800000.
chip1 <Intel 82371 (Triton)> rev 2 on pci0:15
pci0: uses 8392704 bytes of memory from fe000000 upto fedfffff.
pci0: uses 256 bytes of I/O space from fc00 upto fcff.
changing root device to sd0a
BIOS Geometries:
0:03fe3f20 0..1022=1023 cylinders, 0..63=64 heads, 1..32=32 sectors
0 accounted for
sd0s1: type 0xa5, start 32, end = 4003839, size 4003808 : OK
WARNING: / was not properly dismounted.
ahc0: target 0, lun 0 (sd0) timed out
sd0(ahc0:0:0): BUS DEVICE RESET message queued.
sd0(ahc0:0:0): ABORTED COMMAND asc:4e,0 Overlapped commands attempted
, retries:4
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.SUN.3.91.960414170326.14069C-100000>