Date: Sat, 10 Feb 2001 0:59:32 EST From: Ken Harrenstien <klh@panix.com> To: Darren Joy <darrenj@uk.uu.net> Cc: klh@panix.com, freebsd-scsi@FreeBSD.ORG Subject: Re: Continuing Problems with DC390W and 4.2 Release Message-ID: <CMM.0.90.4.981784772.klh@panix2.panix.com>
next in thread | raw e-mail | index | archive | help
Hi,
Was searching through the archives to see if anyone else has had
problems similar to mine, and found yours. I was wondering if there
had been any further resolution since the last round of messages
circa 7-Jan-2001?
If not, perhaps my info will add some data for Gerard or others.
My story is that I just now began trying to move from 3.3 to 4.2
(because only 4.x can understand large ATA drives, sigh) and ran into
some odd error messages that look like this:
sym0:0: message d sent on bad reselection.
sym0:0:control msgout: 80 20 35 d.
I have a Tekram DC390-U2W and this problem is happening with a Conner
CFP1080S (Conner again... hmmm). Tagged Queueing is enabled. It
isn't frequent, but I haven't tried much yet. Happened once during
shutdown for a reboot (which wedged things and required a fsck after
resetting the CPU), again upon logging in after a night of running
idle. There are currently two other devices on the SCSI chain but
they should be completely unused (nothing is mounted from them).
I would have used the NCR driver, except I couldn't figure out how to
coerce the new 4.2 /usr/sbin/config to accept the setting of
SCSI_NCR_DFLT_SYNC=6 which is required in order to use LVD drives at
full 80Mb/s speed. Grumble. Different topic. Was hoping SYM would work
without this fussing, but until I understand what's going on with "bad
reselection" I'm not going to put my LVD drives on this system.
Here's the dmesg since it always seems to be asked for. Apologies if
it turns out to be unnecessary!
--Ken
--------------
ghost:~> dmesg
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #0: Fri Feb 9 01:52:53 PST 2001
klh@ghost:/usr/src/sys/compile/PCKLH-300
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 300683344 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x660 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 268419072 (262128K bytes)
avail memory = 257679360 (251640K bytes)
Preloaded elf kernel "kernel" at 0xc039f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 4.2
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 4.3 on pci0
sym0: <895> port 0xd000-0xd0ff mem 0xe0800000-0xe0800fff,0xe1000000-0xe10000ff irq 11 at device 10.0 on pci0
sym0: Tekram NVRAM, ID 7, Fast-40, SE, parity checking
pci0: <Cirrus Logic GD5446 SVGA controller> at 12.0
dc0: <82c169 PNIC 10/100BaseTX> port 0xb800-0xb8ff mem 0xe0000000-0xe00000ff irq 10 at device 13.0 on pci0
dc0: Ethernet address: 00:c0:f0:2d:89:bc
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 1000 packets/entry by default
ad0: 43979MB <IBM-DTLA-307045> [89355/16/63] at ata0-master UDMA33
Waiting 5 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS mode change from SE to SE.
Mounting root from ufs:/dev/da0s1a
cd0 at sym0 bus 0 target 5 lun 0
cd0: <TOSHIBA XM-4101TASUNSLCD 1084> Removable CD-ROM SCSI-2 device
cd0: 4.237MB/s transfers (4.237MHz, offset 15)
cd0: cd present [1304908 x 512 byte records]
da0 at sym0 bus 0 target 0 lun 0
da0: <CONNER CFP1080S 3939> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 1030MB (2110812 512 byte sectors: 255H 63S/T 131C)
da1 at sym0 bus 0 target 1 lun 0
da1: <IBM DORS32160SUN2.1G WA7A> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 2063MB (4226725 512 byte sectors: 255H 63S/T 263C)
sym0:0: message d sent on bad reselection.
sym0:0:control msgout: 80 20 35 d.
ghost:~>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CMM.0.90.4.981784772.klh>