Date: Wed, 18 Feb 2004 16:00:26 -0000 From: "Aled Treharne" <Aled.T@mistral.net> To: <freebsd-stable@freebsd.org> Subject: Kernel panic on install (ATA READ timeout) Message-ID: <D869343A133CF94B8C7985D6DBDFAB87719A@hqex2.hq.mistral.co.uk>
next in thread | raw e-mail | index | archive | help
Hi all.
I'm trying to install FreeBSD 4.9 onto a Nexcom blade (model HDB31670).
Both Debian and Windows install OK, however FreeBSD panics on boot from
the CDROM (full output is below). I've dried disabling DMA and setting
the PIO mode manually with no effect. I've also tried googling, but I
haven't seen anything resembling this problem. The CDROM is a mini-ISO,
but I've also tried a disc1 ISO, and both were known good burns that
have worked on other hardware, and whose MD5 sums match.
I'm hoping that there's someone else out there with similar hardware to
this who can offer some advice...
Thanks in advance.
Cheers,
Aled.
BTX loader 1.00 BTX version is 1.01
Console: international video/keyboard
BIOS drive A: is disk0
avail memory =3D 1037373440 (1013060K bytes)
Preloaded elf kernel "kernel" at 0xc0829000.
Preloaded mfs_root "/mfsroot" at 0xc0829084.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03ef094
md1: Malloc disk
Using $PIR table, 6 entries at 0xc00fdd30
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Chips and Technologies model 0c30 VGA-compatible display device>
at 12.0 irq 7
fxp0: <Intel 82559 Pro/100 ethernet> mem
0xfa000000-0xfa0fffff,0xfa100000-0xfa100fff irq 5 at device 14.0 on pci0
fxp0: ethernet address: 00:10:f3:00:09:0a
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=3D1166 device=3D0201)> at device 15.0 =
on
pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 ATA100 controller> port
0xe800-0xe803,0xe400-0xe40f,0xe000-0xe003,0xdc00-0xdc007,0xd800-0xd803,0
xd400-0xd407 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci1: <PCI bus> on pcib1
bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xfb000000-0xfb00ffff irq 10 at device 12.0 on pci1
bge0: Ethernet address: 00:10:f3:00:09:08
miibus1: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xfb010000-0xfb01ffff irq 11 at device 13.0 on pci1
bge1: Ethernet address: 00:10:f3:00:09:09
miibus2: <MII bus> on bge1
brgphy1: <BCM5701 10/100/1000baseTX PHY> on miibus2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0: configured irq4 not in bitmap of probed irqs -
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found
ad0: READ command timeout tag=3D0 serv=3D0 - resetting
ata0: resetting devices .. done
ad0: 38154MB <FUJITSU MHR2040AT> [77520/16/63] at ata0-master UDMA100
ad0: READ command timeout tag=3D0 serv=3D0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=3D0 serv=3D0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=3D0 serv=3D0 - resetting
ad0: trying fallback to PIO mode
ata0: resetting devices .. done
Fatal trap 12: page fault while in kernel mode
fault virtual address =3D 0xf00090
fault code =3D supervisor read, page not present
instruction pointer =3D 0x8:0xc02141cb
stack pointer =3D 0x10:0xc038b0b0
frame pointer =3D 0x10:0xc038b0e8
code segment =3D base 0x0, limit 0xfffff, type 0x1b
=3D DPL 0, pres 1, def32 1, gran 1
processor eflags =3D interrupt enabled, resume, IOPL =3D 0
current process =3D Idle
interrupt mask =3D bio
trap number =3D 12
panic: page fault
syncing disks...
--=20
Aled Treharne - Network Operations - Mistral Internet
Tel: 0870 751 6300 Fax: 0870 751 6399 http://www.mistral.net=20
This electronic message contains information from Mistral Internet which
may be privileged or confidential. The information is intended to be for
the use of the individual(s) or entity named above. If you are not the
intended recipient be aware that any disclosure, copying, distribution
or use of the contents of this information is prohibited. If you have
received this electronic message in error, please notify us by telephone
or email (to the numbers or address above) immediately.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?D869343A133CF94B8C7985D6DBDFAB87719A>