Date: Sat, 22 Dec 2007 03:42:22 +0000 From: Luke <lukeedgeworth@googlemail.com> To: freebsd-current@freebsd.org Cc: lukeedgeworth@googlemail.com Subject: Re: Can't install FreeBSD Current or 7.0 on AMD Turion 64x2 Mobile TL-58 1.9 Ghz in an Acer 5520-5679 Message-ID: <56cee8d50712211942r578ffee2wbd7a27866d29ddd9@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
I've got an earlier model ACER TravelMate 515 from the 5510 series which
boots just fine, shame it came with a crappy broadcom wireless card, which
only linux has a driver for I think.
My only quirk is powering off or rebooting, it'll hang just after the kernel
spits out the uptime. No biggy, I just hold the power button for a few
seconds. OpenBSD does the samething, not tried any other OS with exception
of Vista.
dmesg attached & seasons greetings.
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA4 #0: Sun Dec 2 16:34:41 UTC 2007
root@myers.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-60 (1995.01-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x40f82 Stepping = 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x2001<SSE3,CX16>
AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8>
Cores per package: 2
usable memory = 2133479424 (2034 MB)
avail memory = 2058809344 (1963 MB)
ACPI APIC Table: <PTLTD APIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <ACRSYS ACRPRDCT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, 1000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
powernow0: <PowerNow! K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem
0xc8000000-0xcfffffff,0xc0100000-0xc010ffff irq 18 at device 0.0 on pci1
acpi_video0: <ACPI video extension> on vgapci0
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci4: <ACPI PCI bus> on pcib3
atapci0: <ATI IXP400 SATA150 controller> port
0x8440-0x8447,0x8434-0x8437,0x8438-0x843f,0x8430-0x8433,0x8400-0x840f mem
0xc0004000-0xc00041ff irq 22 at device 18.0 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ohci0: <ATI SB400 USB Controller> mem 0xc0005000-0xc0005fff irq 19 at device
19.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> mem 0xc0006000-0xc0006fff irq 19 at device
19.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> mem 0xc0007000-0xc0007fff irq 19 at
device 19.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 8 ports with 8 removable, self powered
ugen0: <vendor 0x5986 Acer OrbiCam, class 239/2, rev 2.00/1.00, addr 2> on
uhub2
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP400 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8420-0x842f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
ata1: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci6: <ACPI PCI bus> on pcib4
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem
0xc0200000-0xc02000ff irq 21 at device 1.0 on pci6
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> PHY 0 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:1b:38:aa:aa:3c
rl0: [ITHREAD]
cbb0: <PCI-CardBus Bridge> mem 0xc0201000-0xc0201fff irq 20 at device 4.0 on
pci6
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
pci6: <memory, flash> at device 4.1 (no driver attached)
pci6: <base peripheral> at device 4.2 (no driver attached)
pci6: <memory, flash> at device 4.3 (no driver attached)
pci6: <memory, flash> at device 4.4 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acd0: DVDR <Slimtype DVD A DS8A1P/CA11> at ata0-master UDMA33
ad4: 152627MB <WDC WD1600BEVS-22RST0 04.01G04> at ata2-master SATA150
ath0: <Atheros 5212> mem 0xc0210000-0xc021ffff irq 20 at device 0.0 on
cardbus0
ath0: [ITHREAD]
ath0: using obsoleted if_watchdog interface
ath0: Ethernet address: 00:19:e0:ff:ff:5d
ath0: mac 7.8 phy 4.5 radio 5.6
SMP: AP CPU #1 Launched!.
GEOM_LABEL: Label for provider ad4s5 is ufs/Data.
Trying to mount root from ufs:/dev/ad4s1a
--
Family means too much, friends are too valuable, and life is too short to
put-off sharing with people how much they really mean to you and pursuing
whatever it is that makes you happy.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?56cee8d50712211942r578ffee2wbd7a27866d29ddd9>