Date: Wed, 05 Feb 2003 21:08:37 +0300 From: Victor Ponomarev <vick@unet.ru> To: Lanny Baron <lnb@FreeBSDsystems.COM> Cc: freebsd-current@freebsd.org, freebsd-smp@freebsd.org Subject: Re: se7500+dual xeon? Message-ID: <3E415325.9040108@unet.ru> References: <3E40DFFF.3040706@unet.ru> <1044453587.52830.69.camel@panda.FreeBSDsystems.COM>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi Lanny! I've used the last BIOS (0501.P05) from Intel (BMC 0.19, FRU/SDR 5.0.9, BIOS production release 4.0 (dated 2003-12-14)) BIOS shipped with the board didn't recognize XEON 2600 Mgz processors. Old BIOS (0468.P01) on another machine shows the same warning... SMP work well for 4.7-STABLE Are a lot of warning about ACPI-0625 and following messages ACPI-1287: *** Error: Method execution failed, AE_NOT_EXIST pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P5 - AE_NOT_FOUND acpi0: power button is handled as a fixed feature programming model. correct? Using old kernel building process (config KERNEL and so on) doesn't work for freebsd 5.0, seems one should use make buildkernel instead... Lanny Baron wrote: >Victor, >You have something messed up. Did you update the bios correctly? Look >at your kernel as well. > >We use the westville for several Servers and it boots multi-processor >just fine. In fact, the hyperthreading works and when booting you should >see 4 cpu's come up. > >Cheers, >Lanny Baron >http://www.FreeBSDsystems.com > >On Wed, 2003-02-05 at 04:57, Victor Ponomarev wrote: > > >>Hi All. >> >>It's seems that smp kernel configuration doesn't work correctly on >>Intel SE7500WV2 motherboard >>with 2 xeon processors in 5.0-RELEASE. >> >>Copyright (c) 1992-2003 The FreeBSD Project. >>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >>FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003 >> root@hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC >>Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000. >>Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06730a8. >>Timecounter "i8254" frequency 1193182 Hz >>Timecounter "TSC" frequency 2592366912 Hz >>CPU: Pentium 4 (2592.37-MHz 686-class CPU) >> Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 >> >>Features=0xffffffffbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,<b31>> >>real memory = 2147418112 (2047 MB) >>avail memory = 2083561472 (1987 MB) >>Initializing GEOMetry subsystem >>Pentium Pro MTRR support enabled >> ACPI-0625: *** Warning: Type override - [DEB_] had invalid type >>(Integer) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [MLIB] had invalid type >>(Integer) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [DATA] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [SIO_] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [LEDP] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [GPEN] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [GPST] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [WUES] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [WUSE] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [SBID] had invalid type >>(String) for Scope operator, changed to (Scope) >> ACPI-0625: *** Warning: Type override - [SWCE] had invalid type >>(String) for Scope operator, changed to (Scope) >>npx0: <math processor> on motherboard >>npx0: INT 16 interface >>acpi0: <INTEL SWV20 > on motherboard >> ACPI-1287: *** Error: Method execution failed, AE_NOT_EXIST >> ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 >> ACPI-0625: *** Info: GPE Block1 defined as GPE16 to GPE47 >>Using $PIR table, 19 entries at 0xc00f3070 >>acpi0: power button is handled as a fixed feature programming model. >>Timecounter "ACPI-fast" frequency 3579545 Hz >>acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 >>acpi_cpu0: <CPU> on acpi0 >>acpi_cpu1: <CPU> on acpi0 >>acpi_cpu2: <CPU> on acpi0 >>acpi_cpu3: <CPU> on acpi0 >>pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >>pci0: <ACPI PCI bus> on pcib0 >>pci0: <unknown> at device 0.1 (no driver attached) >>pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0 >>pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P5 - >>AE_NOT_FOUND >>pci2: <ACPI PCI bus> on pcib1 >>pci2: <base peripheral, interrupt controller> at device 28.0 (no driver >>attached) >>pcib2: <ACPI PCI-PCI bridge> at device 29.0 on pci2 >>pci4: <ACPI PCI bus> on pcib2 >>pci2: <base peripheral, interrupt controller> at device 30.0 (no driver >>attached) >>pcib3: <ACPI PCI-PCI bridge> at device 31.0 on pci2 >>pci3: <ACPI PCI bus> on pcib3 >>em0: <Intel(R) PRO/1000 Network Connection, Version - 1.4.7> port >>0x2040-0x207f mem 0xfeac0000-0xfeadffff irq 10 at device 7.0 on pci3 >>em0: Speed:N/A Duplex:N/A >>em1: <Intel(R) PRO/1000 Network Connection, Version - 1.4.7> port >>0x2000-0x203f mem 0xfeae0000-0xfeafffff irq 10 at device 7.1 on pci3 >>em1: Speed:N/A Duplex:N/A >>pci0: <unknown> at device 3.1 (no driver attached) >>pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 >>pci1: <ACPI PCI bus> on pcib4 >>atapci0: <Promise TX2 ATA133 controller> port >>0x1420-0x142f,0x140c-0x140f,0x1410-0x1417,0x1408-0x140b,0x1400-0x1407 >>mem 0xfe9e0000-0xfe9e3fff irq 9 at device 2.0 on pci1 >>ata2: at 0x1400 on atapci0 >>ata3: at 0x1410 on atapci0 >>pci1: <display, VGA> at device 12.0 (no driver attached) >>isab0: <PCI-ISA bridge> at device 31.0 on pci0 >>isa0: <ISA bus> on isab0 >>atapci1: <Intel ICH3 ATA100 controller> port >>0x3a0-0x3af,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 >>ata0: at 0x1f0 irq 14 on atapci1 >>ata1: at 0x170 irq 15 on atapci1 >>pci0: <serial bus, SMBus> at device 31.3 (no driver attached) >>atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 >>atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 >>kbd0 at atkbd0 >>acpi_ec0: <embedded controller> port 0xca7,0xca6 on acpi0 >>fdc0: cmd 3 failed at out byte 1 of 3 >>sio0 port 0x3f8-0x3ff irq 4 on acpi0 >>sio0: type 16550A >>sio1 port 0x2f8-0x2ff irq 3 on acpi0 >>sio1: type 16550A >>fdc0: cmd 3 failed at out byte 1 of 3 >>orm0: <Option ROMs> at iomem >>0xd3000-0xd47ff,0xd1800-0xd2fff,0xc8000-0xd17ff,0xc0000-0xc7fff on isa0 >>pmtimer0 on isa0 >>fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port >>0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 >>fdc0: FIFO enabled, 8 bytes threshold >>fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >>ppc0: parallel port not found. >>sc0: <System console> at flags 0x100 on isa0 >>sc0: VGA <16 virtual consoles, flags=0x300> >>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >>Timecounters tick every 10.000 msec >>acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4 >>ar0: 76319MB <ATA SPAN array> [9729/255/63] status: READY subdisks: >> 0 READY ad4: 76319MB <ST380021A> [155061/16/63] at ata2-master UDMA100 >>ar1: 78533MB <ATA SPAN array> [10011/255/63] status: READY subdisks: >> 0 READY ad6: 78533MB <IC35L080AVVA07-0> [159560/16/63] at ata3-master >>UDMA100 >>Opened disk ad4 -> 16 >>Opened disk ad4 -> 16 >>Opened disk ad4 -> 16 >>Opened disk ad4 -> 16 >>Opened disk ad6 -> 16 >>Opened disk ad6 -> 16 >>Mounting root from ufs:/dev/ar0s1a >> >> >> >>To Unsubscribe: send mail to majordomo@FreeBSD.org >>with "unsubscribe freebsd-smp" in the body of the message >> >> To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3E415325.9040108>