Date: Mon, 29 Mar 2004 16:17:26 -0800 (PST) From: Julian Elischer <julian@elischer.org> To: freebsd-stable@freebsd.org Subject: Re: USB2 device Message-ID: <Pine.BSF.4.21.0403291600580.29660-100000@InterJet.elischer.org> In-Reply-To: <1080603100.353.3.camel@fast.mmercer.com>
next in thread | previous in thread | raw e-mail | index | archive | help
here's mine:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 4.8-RELEASE-p15 #13: Mon Mar 29 13:34:08 PST 2004
root@teraserver.dev.vicor-nb.com:/usr/obj/usr/prod/system/VERS_4_8_BRANCH/src/sys/VICOR
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 2800107696 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.11-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf25 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073659904 (1048496K bytes)
avail memory = 1040945152 (1016548K bytes)
Preloaded elf kernel "k2" at 0xc0456000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f23c0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=2561)> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xd800-0xd81f
irq 5 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xd400-0xd41f
irq 9 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xd000-0xd01f
irq 9 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7000000-0xf70003ff irq
11 at device 29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
pci0
pci2: <PCI bus> on pcib2
bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xf6800000-0xf6801fff irq 10
at device 5.0 on pci2
bfe0: Ethernet address: 00:0e:a6:18:a4:72
miibus0: <MII bus> on bfe0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci2: <ATI Mach64-GR graphics accelerator> at 9.0 irq 9
ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xb400-0xb4ff mem
0xf4000000-0xf4000fff irq 9 at device 10.0 on pci2
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
pcm0: <Creative CT5880-E> port 0xb000-0xb03f irq 10 at device 12.0 on
pci2
pcm0: <unknown ac97 codec> (id=0x454d4328)
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa800-0xa83f mem
0xf3000000-0xf301ffff,0xf3800000-0xf3800fff irq 9 at device 13.0 on pci2
fxp0: Ethernet address 00:02:b3:ea:e7:d6
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=24c0)> at device 31.0 on
pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 ATA100 controller> port
0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0-0x7 irq 9 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcm1: <Intel 82801DB (ICH4)> port 0x9400-0x943f,0x9800-0x98ff mem
0xf2000000-0xf20000ff,0xf2800000-0xf28001ff irq 9 at device 31.5 on pci0
pcm1: <unknown ac97 codec> (id=0x41445370)
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc87ff,0xcc000-0xcd7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Polled port
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled, default to accept, logging disabled
IPsec: Initialized Security Association Processing.
ad0: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata0-master UDMA100
Waiting 4 seconds for SCSI devices to settle
uscanner0: at uhub0 port 2 (addr 2) disconnected
uscanner0: detached
uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2
Mounting root from ufs:/dev/ad0s1a
umass0: LEXAR MEDIA JUMPDRIVE PRO, rev 2.00/0.00, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <LEXAR JUMPDRIVE PRO 0> Removable Direct Access SCSI-2 device
da0: 650KB/s transfers
da0: 246MB (503808 512 byte sectors: 64H 32S/T 246C)
(da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not supported, increasing
minimum_cmd_size to 10.
jtest# usbdevs -v
Controller /dev/usb0:
addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 addr 2: low speed, self powered, config 1, HP ScanJet
6200C(0x0201), Hewlett-Packard(0x03f0), rev 1.00
Controller /dev/usb1:
addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb2:
addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb3:
addr 1: low speed, self powered, config 1, EHCI root hub(0x0000),
(0x8086)(0x0000), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
port 5 powered
port 6 addr 2: low speed, power 200 mA, config 1, JUMPDRIVE
PRO(0x0200), LEXAR MEDIA(0x05dc), rev 0.00
jtest#
jtest# dd if=/dev/da0 of=/dev/null bs=64k
Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not
supported, increasing minimum_cmd_size to 10.
Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not
supported, increasing minimum_cmd_size to 10.
3936+0 records in
3936+0 records out
257949696 bytes transferred in 47.199914 secs (5465046 bytes/sec)
jtest#
jtest# cat VICOR
machine i386
cpu I586_CPU
cpu I686_CPU
ident VICOR
maxusers 256
makeoptions DEBUG=-g
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Faster in large dirs (memory
tradeoff)
options MFS #Memory Filesystem
options NFS #Network Filesystem
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=4000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time
extensions
options _KPOSIX_PRIORITY_SCHEDULING
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options INCLUDE_CONFIG_FILE # Include this file in kernel
options DDB
#options DDB_UNATTENDED
options KTRACE #kernel tracing
options IPDIVERT #Divert sockets
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/
IPSEC)
options IPFIREWALL #Packet firewall
options IPFIREWALL_DEFAULT_TO_ACCEPT #Only block on firewall
machines
options IPFIREWALL_FORWARD
options MAXDSIZ=(2047*1024*1024)
#options SMP # Symmetric MultiProcessor
Kernel
#options APIC_IO # Symmetric (APIC) I/O
#options HTT # HyperThreading Technology
device isa
device pci
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
options ATA_STATIC_ID #Static device numbering
device ahc # AHA2940 and onboard AIC7xxx devices
device dpt # DPT Smartcache - See LINT for
options!
device mlx
device mly
device twe
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough dev (direct SCSI
access)
device pt
device ch
device ses
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
pseudo-device splash
device sc0 at isa? flags 0x100
device npx0 at nexus? port IO_NPX irq 13
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device ppc0 at isa?
device ppbus
device lpt
device em # Intel PRO/1000 adapter Gigabit
Ethernet Card (``Wiseman'')
device miibus
device bfe # Broadcom BCM440x
device bge # Broadcom BCM570x (``Tigon
III'')
device fxp
device pcm
device xdcp
device cy0
#options CY_PCI_FASTINTR # Use with cy_pci unless irq is
shared
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device bpf #Berkeley packet filter
pseudo-device vn
pseudo-device gif #IPv6 and IPv4 tunneling
pseudo-device speaker
# USB support
device ehci # EHCI PCI->USB interface
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
#device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires
scbus and da
device ums # Mouse
device uscanner # Scanners
device firewire # Generic
device fwe # Generic
device sbp # Generic
jtest#
ignore the xdcp entry... it's local.
I don;t see any mention of cam or SCSI in your config..
umass requires cam asn they implement SCSI-over-USB
to get the disk function.
This is not however perfect.. I get hangs on boot if the drive is
already inserted, and sometimes it doesn't notice that it is removed...
but it does give me 5.4MBytes/sec which is > than teh theoretical
maximum of about 1.5MB/sec for USB1.1
julian
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0403291600580.29660-100000>