Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 22 May 2013 00:05:31 -0300
From:      Giorgio Emanuel <giorgiolago@gmail.com>
To:        freebsd-net@freebsd.org
Subject:   em2: watchdog timeout - resetting
Message-ID:  <CAJAYy1gqC%2BFQYDdOO=j1AYqeew=XHdKA1=H9M1-piaLiMjnksw@mail.gmail.com>

next in thread | raw e-mail | index | archive | help
Hello, I have a server pfsense in bridge mode to function as transparent
FW, the problem is that once I connect the pfsense between my router core
and my core switch catalyst a few seconds begin to appear several messages
like these:

em2: watchdog timeout - resetting
em2: watchdog timeout - resetting
em2: watchdog timeout - resetting
em2: watchdog timeout - resetting

And the connection falls back repeatedly and indefinitely.
Searching on google did some tweaks:

hw.em.rxd =3D "4096"
hw.em.txd =3D "4096"
hw.em.tx_int_delay =3D "250"
hw.em.rx_int_delay =3D "250"
hw.em.tx_abs_int_delay =3D "250"
hw.em.rx_abs_int_delay =3D "250"
hw.em.enable_msix =3D "0"
hw.em.msix_queues =3D "2"
hw.em.rx_process_limit =3D "-1"
hw.em.fc_setting =3D "0"
hw.em.num_queues =3D 1

I tried several variations, but also without success.

My infrastructure:

(7301 cisco router) ------ em1 (pfsense bridge0) em2 ------ sw core cisco
catalyst

I tried also a fresh installation of pfsense 2.0.3 without success.
My network card is an Intel =AE PRO/1000 MT Dual Port Server Adapter PCI-X =
on
a 32-bit PCI slot, operating bridge in 1 <-> em2.
Motherboard ASUS P8H61-V and CPU corei5, I tried disabling all onboard
devices, also without success.
I have 4 nics identical, tested one per one  all without success also.
I am using the latest bios from ASUS site, I tried various combinations of
bios, also without success.
I tried to activate the device polling unsuccessfully to solve the problem.
I tried disable acpi on boot menu but the ser without acpi wont boot.
I tried disable TOE, FLOW CONTROL, no sucess.

This is a link to a troughput 60 Mbits with multiple VLANs (more than 200)
Wisp provider.
I tested the same server same hardware but using linux (debian 6) did the
bridges, and everything worked properly!, so it is clear that this is a
problem software (in intel em driver?)
Tested on another server (P5VD2MX + Core2Duo) but with the same NIC, and
the problem occurs in the same way.
I realized that it generates a huge number of interruptions em2 over 200
thousand.

#vmstat -i
interrupt                          total       rate
irq16: em1                         12891         40
irq17: em2                        546630       1713
irq19: atapci0                      5181         16
irq23: ehci0 ehci1                  1049          3
cpu0: timer                       637069       1997
irq256: em0                         1557          4
cpu3: timer                       636939       1996
cpu2: timer                       636939       1996
cpu1: timer                       636938       1996
Total                            3115193       9765

Data for debug:

[2.0.3-RELEASE] [root@pfsense.localdomain] / root (1): sysctl hw.em
hw.em.eee_setting: 0
hw.em.rx_process_limit: 100
hw.em.enable_msix: 0
hw.em.sbp: 0
hw.em.smart_pwr_down: 0
hw.em.txd: 4096
hw.em.rxd: 4096
hw.em.rx_abs_int_delay: 66
hw.em.tx_abs_int_delay: 66
hw.em.rx_int_delay: 0
hw.em.tx_int_delay: 0

[2.0.3-RELEASE] [root@pfsense.localdomain] / root (3): sysctl dev.em.2
dev.em.2.% desc: Intel (R) PRO/1000 Legacy Network Connection 1.0.4
dev.em.2.% driver: in
dev.em.2.% location: slot =3D 0 function =3D 1
dev.em.2.% pnpinfo: vendor =3D 0x8086 device =3D 0x1079 subvendor =3D 0x808=
6
subdevice =3D 0x1179 class =3D 0x020000
dev.em.2.% parent: PCI4
dev.em.2.nvm: -1
dev.em.2.rx_int_delay: 0
dev.em.2.tx_int_delay: 0
dev.em.2.rx_abs_int_delay: 66
dev.em.2.tx_abs_int_delay: 66
dev.em.2.rx_processing_limit: 100
dev.em.2.flow_control: 0
dev.em.2.mbuf_alloc_fail: 0
dev.em.2.cluster_alloc_fail: 0
dev.em.2.dropped: 0
dev.em.2.tx_dma_fail: 0
dev.em.2.tx_desc_fail1: 0
dev.em.2.tx_desc_fail2: 0
dev.em.2.rx_overruns: 0
dev.em.2.watchdog_timeouts: 0
dev.em.2.device_control: 1076888137
dev.em.2.rx_control: 32794
dev.em.2.fc_high_water: 47104
dev.em.2.fc_low_water: 45604
dev.em.2.fifo_workaround: 0
dev.em.2.fifo_reset: 0
dev.em.2.txd_head: 243
dev.em.2.txd_tail: 243
dev.em.2.rxd_head: 1374
dev.em.2.rxd_tail: 1373
dev.em.2.mac_stats.excess_coll: 0
dev.em.2.mac_stats.single_coll: 0
dev.em.2.mac_stats.multiple_coll: 0
dev.em.2.mac_stats.late_coll: 0
dev.em.2.mac_stats.collision_count: 0
dev.em.2.mac_stats.symbol_errors: 0
dev.em.2.mac_stats.sequence_errors: 0
dev.em.2.mac_stats.defer_count: 0
dev.em.2.mac_stats.missed_packets: 0
dev.em.2.mac_stats.recv_no_buff: 0
dev.em.2.mac_stats.recv_undersize: 0
dev.em.2.mac_stats.recv_fragmented: 0
dev.em.2.mac_stats.recv_oversize: 0
dev.em.2.mac_stats.recv_jabber: 0
dev.em.2.mac_stats.recv_errs: 0
dev.em.2.mac_stats.crc_errs: 0
dev.em.2.mac_stats.alignment_errs: 0
dev.em.2.mac_stats.coll_ext_errs: 0
dev.em.2.mac_stats.xon_recvd: 0
dev.em.2.mac_stats.xon_txd: 0
dev.em.2.mac_stats.xoff_recvd: 0
dev.em.2.mac_stats.xoff_txd: 0
dev.em.2.mac_stats.total_pkts_recvd: 6681156
dev.em.2.mac_stats.good_pkts_recvd: 6681156
dev.em.2.mac_stats.bcast_pkts_recvd: 17313
dev.em.2.mac_stats.mcast_pkts_recvd: 156511
dev.em.2.mac_stats.rx_frames_64: 1199707
dev.em.2.mac_stats.rx_frames_65_127: 2110104
dev.em.2.mac_stats.rx_frames_128_255: 396 862
dev.em.2.mac_stats.rx_frames_256_511: 196001
dev.em.2.mac_stats.rx_frames_512_1023: 138581
dev.em.2.mac_stats.rx_frames_1024_1522: 2639901
dev.em.2.mac_stats.good_octets_recvd: 4439337234
dev.em.2.mac_stats.good_octets_txd: 15529
dev.em.2.mac_stats.total_pkts_txd: 143
dev.em.2.mac_stats.good_pkts_txd: 143
dev.em.2.mac_stats.bcast_pkts_txd: 104
dev.em.2.mac_stats.mcast_pkts_txd: 39
dev.em.2.mac_stats.tx_frames_64: 48
dev.em.2.mac_stats.tx_frames_65_127: 69
dev.em.2.mac_stats.tx_frames_128_255: 20
dev.em.2.mac_stats.tx_frames_256_511: 6
dev.em.2.mac_stats.tx_frames_512_1023: 0
dev.em.2.mac_stats.tx_frames_1024_1522: 0
dev.em.2.mac_stats.tso_txd: 0
dev.em.2.mac_stats.tso_ctx_fail: 0


#uname -a
FreeBSD pfsense.localdomain 8.1-RELEASE-p13 FreeBSD 8.1-RELEASE-p13 #1: Fri
Apr 12 10:58:43 EDT 2013
root@snapshots-8_1-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSenses=
rc/src/sys/pfSense_SMP.8
 amd64

# Pciconf-lvc:

em1 @ pci0: 4:0:0: class =3D 0x020000 card =3D 0x11798086 chip =3D 0x107980=
86 rev
=3D 0x03 hdr =3D 0x00
    class =3D network
    subclass =3D ethernet
    cap 01 [dc] =3D powerspec 2 supports D0 D3 current D0
    cap 07 [e4] =3D PCI-X 64-bit supports 133MHz, 2048 burst read, 1 split
transaction
em2 @ pci0: 4:0:1: class =3D 0x020000 card =3D 0x11798086 chip =3D 0x107980=
86 rev
=3D 0x03 hdr =3D 0x00
    class =3D network
    subclass =3D ethernet
    cap 01 [dc] =3D powerspec 2 supports D0 D3 current D0
    cap 07 [e4] =3D PCI-X 64-bit supports 133MHz, 2048 burst read, 1 split
transaction

dmesg
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p13 #1: Fri Apr 12 10:58:43 EDT 2013
    root@snapshots-8_1-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSe=
nsesrc/src/sys/pfSense_SMP.8
amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM) i5-2310 CPU @ 2.90GHz (2892.73-MHz K8-class CPU)
  Origin =3D "GenuineIntel"  Id =3D 0x206a7  Family =3D 6  Model =3D 2a  St=
epping =3D
7

Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,=
MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>

Features2=3D0x179ae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,C=
X16,xTPR,PDCM,<b17>,SSE4.1,SSE4.2,POPCNT,<b24>,AESNI,XSAVE,<b28>>
  AMD Features=3D0x28100800<SYSCALL,NX,RDTSCP,LM>
  AMD Features2=3D0x1<LAHF>
  TSC: P-state invariant
real memory  =3D 8589934592 (8192 MB)
avail memory =3D 7952838656 (7584 MB)
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  2
 cpu2 (AP): APIC ID:  4
 cpu3 (AP): APIC ID:  6
ioapic0 <Version 2.0> irqs 0-23 on motherboard
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <ALASKA A M I> on motherboard
acpi0: [ITHREAD]
ACPI Error (psargs-0464): [RAMB] Namespace lookup failure, AE_NOT_FOUND
ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW]
(Region) (20100331/nsinit-442)
acpi0: Power Button (fixed)
acpi0: reservation of 67, 1 (4) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem
0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7f04000-0xf7f043ff irq 23
at device 26.0 on pci0
ehci0: [ITHREAD]
usbus0: EHCI version 1.0
usbus0: <EHCI (generic) USB 2.0 controller> on ehci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0xe000-0xe01f mem
0xf7e20000-0xf7e3ffff,0xf7e00000-0xf7e1ffff irq 16 at device 0.0 on pci2
em0: Using an MSI interrupt
em0: [FILTER]
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci3
pci4: <ACPI PCI bus> on pcib4
em1: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xd040-0xd07f
mem 0xf7d20000-0xf7d3ffff,0xf7cc0000-0xf7cfffff irq 16 at device 0.0 on pci=
4
em1: [FILTER]
em2: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xd000-0xd03f
mem 0xf7d00000-0xf7d1ffff,0xf7c40000-0xf7c7ffff irq 17 at device 0.1 on pci=
4
em2: [FILTER]
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7f03000-0xf7f033ff irq 23
at device 29.0 on pci0
ehci1: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel AHCI controller> port
0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f mem
0xf7f02000-0xf7f027ff irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
atapci0: AHCI v1.30 controller with 4 3Gbps ports, PM not supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ad4: 476940MB <Seagate ST3500418AS CC35> at ata2-master UDMA100 SATA 3Gb/s
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
acd0: DVDR <ATAPI iHAS124 C/LL02> at ata3-master UDMA100 SATA 1.5Gb/s
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
Root mount waiting for: usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on
usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on
usbus1
Root mount waiting for: usbus1 usbus0
uhub2: 4 ports with 4 removable, self powered
uhub3: 6 ports with 6 removable, self powered
ugen0.3: <USB> at usbus0
ukbd0: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
kbd2 at ukbd0
uhid0: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
Trying to mount root from ufs:/dev/ad4s1a
pflog0: promiscuous mode enabled
em2: link state changed to UP
bridge0: promiscuous mode enabled
pflog0: promiscuous mode disabled
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 0 done
All buffers synced.
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p13 #1: Fri Apr 12 10:58:43 EDT 2013
    root@snapshots-8_1-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSe=
nsesrc/src/sys/pfSense_SMP.8
amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM) i5-2310 CPU @ 2.90GHz (2892.72-MHz K8-class CPU)
  Origin =3D "GenuineIntel"  Id =3D 0x206a7  Family =3D 6  Model =3D 2a  St=
epping =3D
7

Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,=
MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>

Features2=3D0x179ae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,C=
X16,xTPR,PDCM,<b17>,SSE4.1,SSE4.2,POPCNT,<b24>,AESNI,XSAVE,<b28>>
  AMD Features=3D0x28100800<SYSCALL,NX,RDTSCP,LM>
  AMD Features2=3D0x1<LAHF>
  TSC: P-state invariant
real memory  =3D 8589934592 (8192 MB)
avail memory =3D 7952838656 (7584 MB)
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  2
 cpu2 (AP): APIC ID:  4
 cpu3 (AP): APIC ID:  6
ioapic0 <Version 2.0> irqs 0-23 on motherboard
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <ALASKA A M I> on motherboard
acpi0: [ITHREAD]
ACPI Error (psargs-0464): [RAMB] Namespace lookup failure, AE_NOT_FOUND
ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW]
(Region) (20100331/nsinit-442)
acpi0: Power Button (fixed)
acpi0: reservation of 67, 1 (4) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem
0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7f04000-0xf7f043ff irq 23
at device 26.0 on pci0
ehci0: [ITHREAD]
usbus0: EHCI version 1.0
usbus0: <EHCI (generic) USB 2.0 controller> on ehci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0xe000-0xe01f mem
0xf7e20000-0xf7e3ffff,0xf7e00000-0xf7e1ffff irq 16 at device 0.0 on pci2
em0: Using an MSI interrupt
em0: [FILTER]
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci3
pci4: <ACPI PCI bus> on pcib4
em1: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xd040-0xd07f
mem 0xf7d20000-0xf7d3ffff,0xf7cc0000-0xf7cfffff irq 16 at device 0.0 on pci=
4
em1: [FILTER]
em2: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xd000-0xd03f
mem 0xf7d00000-0xf7d1ffff,0xf7c40000-0xf7c7ffff irq 17 at device 0.1 on pci=
4
em2: [FILTER]
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7f03000-0xf7f033ff irq 23
at device 29.0 on pci0
ehci1: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel AHCI controller> port
0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f mem
0xf7f02000-0xf7f027ff irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
atapci0: AHCI v1.30 controller with 4 3Gbps ports, PM not supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ad4: 476940MB <Seagate ST3500418AS CC35> at ata2-master UDMA100 SATA 3Gb/s
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
acd0: DVDR <ATAPI iHAS124 C/LL02> at ata3-master UDMA100 SATA 1.5Gb/s
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on
usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on
usbus1
uhub2: 4 ports with 4 removable, self powered
uhub3: 6 ports with 6 removable, self powered
Root mount waiting for: usbus0
ugen0.3: <USB> at usbus0
ukbd0: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
kbd2 at ukbd0
uhid0: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 3> on usbus0
Trying to mount root from ufs:/dev/ad4s1a
pflog0: promiscuous mode enabled
em2: link state changed to UP
bridge0: promiscuous mode enabled



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJAYy1gqC%2BFQYDdOO=j1AYqeew=XHdKA1=H9M1-piaLiMjnksw>