Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 15 Dec 2004 07:26:01 -0800
From:      sp0ng3b0b <sp0ng3b0b@sbcglobal.net>
To:        sp0ng3b0b <sp0ng3b0b@sbcglobal.net>
Cc:        questions@freebsd.org
Subject:   Re: FreeBSD 5.3: panic page fault with nge driver
Message-ID:  <41C05789.3050300@sbcglobal.net>
In-Reply-To: <41BF5A4C.2000203@sbcglobal.net>
References:  <41BF5A4C.2000203@sbcglobal.net>

next in thread | previous in thread | raw e-mail | index | archive | help
I've been told that this might be fixed in CURRENT. That's nice, but I 
am trying to run a production quality server and CURRENT is not 
recommended for that purpose. Any recommendations?

By the way, is Questions the wrong list for my problem?

sp0ng3b0b wrote:
> I am getting a page fault with a new install of FreeBSD 5.3 Release. 
> Something changed with the nge driver in FreeBSD 5.3. I did not have 
> this problem with 5.2.1. I just performed a clean install on a box that 
> had been running 5.2.1 RELEASE for a few months.
> 
> The box is an Instrusion Detection System. I have fiber taps in place on 
> the network and use the rx ports of the nic to monitor the traffic.
> 
> In 5.2.1, i would do this to bond ports and monitor them:
> 
> # ifconfig nge0 media 1000baseSX mediaopt full-duplex promisc -arp up
> # ifconfig nge1 media 1000baseSX mediaopt full-duplex promisc -arp up
> # ngctl mkpeer fec dummy fec
> # ngctl msg fec0: add_iface '"nge0"'
> # ngctl msg fec0: add_iface '"nge1"'
> # ngctl msg fec0: set_mode_inet
> # ifconfig fec0 promisc -arp up
> 
> However, when i set the media options for nge0, the machine panics and 
> dies. The panic message is hand typed below.
> 
> FreeBSD 5.3 RELEASE.
> Intel Pentium 4 3.06GHz CPU
> 1GB RAM
> 80GB Maxtor HD
> (1x) Intel 82801DB (ICH4) Pro/100 Ethernet
> (6x) NetGear GA621 fiber 1GB NIC
> 
> 
> Fatal trap 12: page fault while in kernel mode
> fault virtual address    = 0x8
> fault code        = supervisor read, page not present
> instruction pointer    = 0x8:0xc055a002
> stack pointer        = 0x10:0xe32a2c9c
> frame pointer        = 0x10:0xe32a2cac
> code segment        = base 0x0, limit 0xfffff, type 0x1b
>             = DPL 0, pres 1, def 2 1, gran 1
> processor eflags    = interrupt enabled, resuep, IOPL = 0
> current process        = 27 (irq17: nge0)
> trap number        = 12
> panic: page fault
> _______________________________________________
> freebsd-questions@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to 
> "freebsd-questions-unsubscribe@freebsd.org"
> 



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?41C05789.3050300>