Date: Fri, 3 Sep 1999 10:43:11 -0700 (PDT) From: Brian <bri@sonicboom.org> To: akhar <jolicom@videotron.ca> Cc: misc@openbsd.org, questions@FreeBSD.ORG Subject: Re: Network doesn't work anymore! Message-ID: <Pine.BSF.4.10.9909031042260.30801-100000@adsl-216-102-203-44.dsl.snfc21.pacbell.net> In-Reply-To: <37C98B4D.C976F4E7@videotron.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
In a case where a trace takes a few minutes but shows sane times, the cause of this is almost always dns. Is named starting on bootup?? Bri On Sun, 29 Aug 1999, akhar wrote: > I have OpenBSD setup as my gateway and server for my networkit > interrfaces with the internet via cable modem on xl0 and with the > intranet on ne3. I have already inquired help from the different > mailling lists and for an hour my network worked! Until I rebooted. Now > I'm stuck I don't know what is wrong! all I can say is that I can do a > tracert from an NT box to my ISP in 3 minutes with two hops: my gateway > and the ISP. here are listed some of my different files in /etc > resolv.conf > domain videotron.ca > nameserver 127.0.0.1 > nameserver 205.... (I can't quite remenber) > nameserver 205.... (samething) > > hosts: > 127.0.0.1 localhost > 127.0.0.1 sphinx.home.foo sphinx > 192.168.0.1 sphinx.home.foo sphinx > 192.168.0.2 tetis.home.foo sphinx #NT box > > mygate: > 192.168.0.1 > > myname: > sphinx > > sphinx# netstat -nr > Routing tables > > Internet: > Destination Gateway Flags Refs Use > Mtu Interface > default 24.200.141.1 UGS 0 44 > - xl0 > 24.200.141/24 link#2 UC 0 0 > - xl0 > 24.200.141.1 8:0:3e:16:1b:59 UHL 1 4 - > xl0 > 24.200.141.104 127.0.0.1 UGHS 0 0 - lo0 > > 127/8 127.0.0.1 UGRS 0 0 > - lo0 > 127.0.0.1 127.0.0.1 UH 3 24 > - lo0 > 192.168.0/24 link#1 UC 0 0 > - ne3 => > 192.168/16 127.0.0.0 URS 0 0 - > lo0 > 192.168.0.2 0:e0:29:39:19:db UHL 2 1408 - ne3 > 224/4 127.0.0.1 URS 0 > 0 - lo0 > > Encap: > Source address/netmask Port Destination address/netmask > Port Prot > o SA(Address/SPI/Proto) > > sphinx# ifconfig -a > lo0: flags=8009<UP,LOOPBACK,MULTICAST> > inet 127.0.0.1 netmask 0xff000000 > lo1: flags=8008<LOOPBACK,MULTICAST> > ne3: flags=8863<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST> > media: Ethernet autoselect (10baseT) > inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 > xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> > media: Ethernet 10baseT (10baseT half-duplex) > inet 24.200.141.104 netmask 0xffffff00 broadcast 255.255.255.255 > > sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> > sl1: flags=c010<POINTOPOINT,LINK2,MULTICAST> > ppp0: flags=8010<POINTOPOINT,MULTICAST> > ppp1: flags=8010<POINTOPOINT,MULTICAST> > tun0: flags=10<POINTOPOINT> > tun1: flags=10<POINTOPOINT> > enc0: flags=8<LOOPBACK> > bridge0: flags=0<> > bridge1: flags=0<> > > What is wrong?? If possible could some give me an exemple of the content > of the different files related to networking and/or a checklist of what > to configure. > Thank you in advance > Akhar > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.9909031042260.30801-100000>