Date: Wed, 19 Nov 1997 01:51:19 +0000 From: Gianmarco Giovannelli <gmarco@giovannelli.it> To: mobile@freebsd.org Subject: Please help me on a Sundisk card... Message-ID: <34724617.5AFB15D@giovannelli.it>
next in thread | raw e-mail | index | archive | help
I am not able to get a SunDisk 15mb compactflash card working... My lucky experince with a 3com and an usr sportser 1626 is irrepetible so I need your help... ############################### Code 128 not found Code 128 not found code Unknown ignored Configuration data for card in slot 1 Tuple #1, code = 0x1 (Common memory descriptor), length = 4 000: df 72 01 ff Common memory device information: Device number 1, type Function specific, WPS = ON Speed = 7.0 x 100 ns, Memory block size = 2Kb, 1 units Tuple #2, code = 0x1c (Other conditions for common memory), length = 4 000: 03 d9 01 ff (MWAIT) (3V card) Tuple #3, code = 0x18 (JEDEC descr for common memory), length = 2 000: df 01 Tuple #4, code = 0x20 (Manufacturer ID), length = 4 000: 45 00 01 04 PCMCIA ID = 0x45, OEM ID = 0x401 Tuple #5, code = 0x15 (Version 1 info), length = 23 000: 04 01 53 75 6e 44 69 73 6b 00 53 44 50 00 35 2f 010: 33 20 30 2e 36 00 ff Version = 4.1, Manuf = [SunDisk],card vers = [SDP] Addit. info = [5/3 0.6],[ÿ] Tuple #6, code = 0x0 (Null tuple), length = 3 000: 14 08 00 Tuple #7, code = 0x21 (Functional ID), length = 2 000: 04 01 Fixed disk card - POST initialize Tuple #8, code = 0x22 (Functional EXT), length = 2 000: 01 01 Modem interface capabilities: Tuple #9, code = 0x22 (Functional EXT), length = 3 000: 02 0c 0f Data modem services available: Tuple #10, code = 0x1a (Configuration map), length = 5 000: 01 07 00 02 0f Reg len = 2, config register addr = 0x200, last config = 0x7 Registers: XXXX---- Tuple #11, code = 0x1b (Configuration entry), length = 11 000: c0 c0 a1 27 55 4d 5d 75 08 00 21 Config index = 0x0(default) Interface byte = 0xc0 (memory) +RDY/-BSY active, wait signal supported Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Max current average over 10 ms: 8 x 10mA Memory space length = 0x8 Max twin cards = 1 Misc attr: (Power down supported) Tuple #12, code = 0x1b (Configuration entry), length = 6 000: 00 01 21 b5 1e 4d Config index = 0x0 Vcc pwr: Nominal operating supply voltage: 3 x 1V, ext = 0x1e Max current average over 10 ms: 4.5 x 10mA Tuple #13, code = 0x1b (Configuration entry), length = 13 000: c1 41 99 27 55 4d 5d 75 64 f0 ff ff 21 Config index = 0x1(default) Interface byte = 0x41 (I/O) +RDY/-BSY active Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Max current average over 10 ms: 8 x 10mA Card decodes 4 address lines, full 8/16 Bit I/O IRQ modes: Level, Pulse IRQ level = 4 Max twin cards = 0 Misc attr: (Read-only) (Power down supported) (Ext byte = 0xff) Tuple #14, code = 0x1b (Configuration entry), length = 6 000: 01 01 21 b5 1e 4d Config index = 0x1 Vcc pwr: Nominal operating supply voltage: 3 x 1V, ext = 0x1e Max current average over 10 ms: 4.5 x 10mA Tuple #15, code = 0x1b (Configuration entry), length = 18 000: c2 41 99 27 55 4d 5d 75 ea 61 f0 01 07 f6 03 01 010: ee 21 Config index = 0x2(default) Interface byte = 0x41 (I/O) +RDY/-BSY active Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Max current average over 10 ms: 8 x 10mA Card decodes 10 address lines, full 8/16 Bit I/O I/O address # 1: block start = 0x1f0 block length = 0x8 I/O address # 2: block start = 0x3f6 block length = 0x2 IRQ modes: Level, Pulse, Shared IRQ level = 14 Max twin cards = 1 Misc attr: (Power down supported) Tuple #16, code = 0x1b (Configuration entry), length = 6 000: 02 01 21 b5 1e 4d Config index = 0x2 Vcc pwr: Nominal operating supply voltage: 3 x 1V, ext = 0x1e Max current average over 10 ms: 4.5 x 10mA Tuple #17, code = 0x1b (Configuration entry), length = 18 000: c3 41 99 27 55 4d 5d 75 ea 61 70 01 07 76 03 01 010: ee 21 Config index = 0x3(default) Interface byte = 0x41 (I/O) +RDY/-BSY active Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Max current average over 10 ms: 8 x 10mA Card decodes 10 address lines, full 8/16 Bit I/O I/O address # 1: block start = 0x170 block length = 0x8 I/O address # 2: block start = 0x376 block length = 0x2 IRQ modes: Level, Pulse, Shared IRQ level = 14 Max twin cards = 1 Misc attr: (Power down supported) Tuple #18, code = 0x1b (Configuration entry), length = 6 000: 03 01 21 b5 1e 4d Config index = 0x3 Vcc pwr: Nominal operating supply voltage: 3 x 1V, ext = 0x1e Max current average over 10 ms: 4.5 x 10mA Tuple #19, code = 0x1b (Configuration entry), length = 4 000: 07 00 28 d3 Config index = 0x7 Tuple #20, code = 0x14 (No link), length = 0 ############################ ################## kernel ## machine "i386" cpu "I586_CPU" ident ARTURO maxusers 10 options INET #InterNETworking options FFS #Berkeley Fast Filesystem options NFS #Network Filesystem options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options BOUNCE_BUFFERS #include support for DMA bounce buffers options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor options "VM86" options XSERVER options ATAPI options ATAPI_STATIC #Don't do it as an LKM options KTRACE #Kernel tracing options SYSVSHM # ---------------------------------------------- # config kernel root on wd0 controller isa0 controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr device wcd0 controller scbus0 device sd0 controller ppbus0 controller ppc0 at isa? port ? irq 7 vector ppcintr controller vpo0 at ppbus? # Zip Parallelo device nlpt0 at ppbus? # Stampante device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr device npx0 at isa? port "IO_NPX" irq 13 vector npxintr device apm0 at isa? flags 0x11 # PCCARD (PCMCIA) support controller card0 device pcic0 at card? device pcic1 at card? device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr device lpt0 at isa? disable port? tty irq 7 vector lptintr device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr #controller snd0 #device sb0 at isa? port 0x220 irq 5 drq 1 vector sbintr #device opl0 at isa? port 0x388 conflicts #options "SBC_IRQ=5" device ep0 at isa? port 0x300 net irq 10 vector epintr pseudo-device loop pseudo-device ether pseudo-device sl 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's pseudo-device bpfilter 4 ############# end kernel... This card requires a new hd entry ??? Thanks for any hints and cheats :-) -- Regards... Gianmarco "Unix expert since yesterday" http://www2.masternet.it
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?34724617.5AFB15D>